Maxouttech RF-RDWS-345-NN User manual

Wireless Recessed Door/Window Sensor
RF-RDWS-345-NN Installation Instructions
RF-RDWS-345-NN IM V1 08042020
Description
The Recessed Door/Window Sensor is a
supervised, wireless sensor that detects the
opening and closing of doors or windows. The
sensor and magnet are recessed mounted
into the frame.
When activated, the sensor transmits an open
(trip) or close (restore) signal to the panel.
These are the signals the unit provides:
supervisory and low battery (as needed). The
sensor is powered by (1) replaceable 3-VDC,
lithium battery.
Mounting the Sensor
•Verify mounting location before drilling
any holes, the area must be able to
accept an 11/16” hole to a depth of 2
1/4” for the sensor and 5/8” for the
magnet
•The holes must be drilled directly
across from each other to ensure the
magnet and sensor operate properly
•Using an 11/16” drill bit drill the hole
for the magnet first, after drilling the
magnet hole mark the location directly
across for the sensor hole.
•The magnet and sensor are slightly
larger than the drilled hole to ensure a
snug fit, a small amount of routing the
hole may be required
•Push both magnet and sensor into
mounting holes
Programming
The following steps describe the general
guidelines for programming the sensor into
panel memory. Refer to the specific panel’s
documentation for complete programming
details.
1. Set the panel to the program mode.
2. Proceed to the SENSORS menu.
3. Select the appropriate sensor group and
sensor number assignments.
4. When prompted by the panel to trip the
sensor for learning:
•Remove the cap from the sensor by
using a screwdriver and twisting the
cap
•Pull the battery tab out to power the
sensor
•After the battery tab is pulled the
sensor will transmit “tampers” for the
first fives activations, the sensor
should be enrolled during one of these
first five trips. If the device is tripped
too many times before enrollment the
battery must be removed and re-
installed to activate the tamper trips
again.
5. Exit program mode.
Testing the Sensor
1. Set the panel to the sensor test mode.
2. Monitor the system after tripping the
sensor. Refer to the specific panel
documentation for interpretation of the results
to ensure desired signal strength is achieved.
Note: If a low battery alarm occurs, replace
the battery within 7 days.
CAUTION: Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in
fire.
Battery Replacement
•Remove the sensor cap and
carefully pull out the circuit board.
•Push out the old battery towards the
antennas and replace with a new
battery.
•Carefully slide board back into
housing, note the slot for alignment.
•Replace the cap and activate the
device at least five times.
Sp
Mount in top or
side of door

Wireless Recessed Door/Window Sensor
RF-RDWS-345-NN Installation Instructions
RF-RDWS-345-NN IM V1 08042020
Specifications
Model no.
RF-RDWS-345-NN
RF frequency
345 MHz
Compatibility
Interlogix Learn Mode Panels
and Receivers – Concord,
NetworX and Simon Series
Battery type
(1) 3-VDC, lithium battery
(Varta or Panasonic,
Battery
Panasonic CR2
Operating
temperature
range
32 to 120°F (0 to 49°C)
Storage
temperature
range
-30 to 140°F (-34 to 60°C)
Relative
humidity
95% non-condensing
Dimensions
2.25” L x .75” D
FCC / IC Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
Per FCC 15.19 (a) (3) and (a) (4), This device complies with
part 15 of the FCC Rules. Operation is subject to the
following conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may cause
undesirable operation.
Per FCC 15.21, The user manual or instruction manual for
an intentional or unintentional radiator shall caution the user
that changes or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Cet appareil est conforme avec Industrie Canada exempts
de licence standard RSS (s). Son fonctionnement est soumis
aux deux conditions suivantes: (1) cet appareil ne doit pas
provoquer d'interférences et (2) cet appareil doit accepter
toute interférence, y compris celles pouvant causer un
mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to
radio frequency fields, the radiating element shall be
installed such that a minimum separation distance of 20 cm
is maintained from the general population.
FCC: 2ABBZ-RF-RDWS-345
IC: 11817A-RFRDWS345
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation. Changes
or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This Class B digital apparatus complies with Canadian
ICES-3B.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
MANUFACTURER HEREBY DISCLAIMS ALL
WARRANTIES AND REPRESENTATIONS, WHETHER
EXPRESS, IMPLIED, STATUTORY OR OTHERWISE
INCLUDING (BUT NOT LIMITED TO) ANY WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO THESE
PRODUCTS AND ANY RELATED SOFTWARE.
MANUFACTURER FURTHER DISCLAIMS ANY OTHER
IMPLIED WARRANTY UNDER THE UNIFORM
COMPUTER INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY STATE.
(USA only) SOME STATES DO NOT ALLOW THE
EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE
EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER LEGAL RIGHTS THAT
VARY FROM STATE TO STATE.
MANUFACTURER MAKES NO REPRESENTATION,
WARRANTY, COVENANT OR PROMISE THAT ITS ALARM
PRODUCTS AND/OR RELATED SOFTWARE (I) WILL NOT
BE HACKED, COMPROMISED AND/OR CIRCUMVENTED;
(II) WILL PREVENT, OR PROVIDE ADEQUATE WARNING
OR PROTECTION FROM, BREAK-INS, BURGLARY,
ROBBERY, FIRE; OR (III) WILL WORK PROPERLY IN ALL