Maxxima M85427R-YCL User manual

M85427R-YCL Installation Manual
Maxxima M85427R-YCL 5.5" Round Flange Mount, Combination Stop/Turn/Tail (STT), Backup, Flashing
Warning, and Optional Amber Turn Signal.
1) 4” Round Red 12 LED Stop, Tail, and Optional Red Turn Signal.All DOT FMVSS108 compliant.
2) 9 LED White Back-Up Light. DOT FMVSS108 compliant.
3) Optional 9 LED Amber Turn Signal. DOT FMVSS108 compliant.
4) Flashing Warning Light: Single Color 9 LED or Dual-Color 18 LED. SAE Class 1 Compliant
Specifications:
LEDs 30 (12 Red/9 White/9Amber)
Voltage 12.8VDC
Amp Draw Tail 20mA, Back-Up 0.2A, Stop 0.2A, Amber Turn 0.1A, Warning 0.4A
Dimensions 5.5” Diameter x 0.5” Depth
Mounting 3 Hole Flange. Bolt circle diameter: 4.9”
Connector 9 Leads 18AWG Blunt Cut, 10.0”
IMPORTANT: Before starting the installation, it is recommended that the light is held in its desired
mounting position temporarily to ensure that the desired location is suitable for placement. Ensure that
proper clearance for the wires and hardware is achieved and that the lights LEDs are unobstructed.
Wiring Designations:
Black Ground (-)
Brown Tail (+VDC)
Blue Back-up (+VDC)
Red Stop & Turn (+VDC)
White Optional Amber Turn (+VDC)
Optional Warning ‘Mode 2’ (-GND)
Green Flashing Warning (+VDC)
Yellow Programming (+VDC)
~ 1 Second Next Flash Pattern
~ 3 –5 Sec. Toggle Color (Single Color Pattern)
~ 7+ Sec. Reset to Pattern # 1

Page 2of 4
Wiring Instructions
First, determine if the vehicle has a dedicated turn signal wire or uses a common wire for both stop light
and turn signal.
TABLE 1: 28 Flash Patterns
3-Wire Stop/Turn/Tail wiring (RED TURN SIGNAL)
If vehicle uses a common wire for both stop light and
turn signal, use the Red Turn Signal by connecting
the Red Wire.
4-Wire Stop/Turn/Tail wiring (AMBER TURN SIGNAL)
If vehicle has a dedicated Left & Right Turn Signal
wires, independent of the Stop Light, use the optional
Amber Turn Signal by connecting the White Wire
3-Wire STT Circuit
4-Wire STT Circuit
Step 1 Connect Black wire to vehicle Ground (- Negative)
Step 2 Connect Brown wire to vehicle Tail Light (+12V)
Step 3 Connect Red wire to vehicle Stop Light (+12V)
Step 4 (Optional) Connect White wire to vehicle Left or Right
Turn Signal (+12V)
Step 5 Connect Blue wire to vehicle Back-up Light (+12V)
Step 6 Connect Green wire “Flashing Warning Circuit” via a
user-supplied switch (+12V)
Step 7 Program Warning to the desired pattern with Yellow
wire.
While the Green wire is connected to +12V, Hold
Yellow wire to +12V for 1 to 2 seconds to scroll to the next
flash pattern (See Table 1). If on a Single-Color pattern, Hold
Yellow wire for 3 to 5 sec to toggle to the alternate color (i.e.
from Amber to White). To reset to Pattern # 1, Hold Yellow
wire to +12V for 7+ seconds.

Page 3of 4
Wiring Instructions (continued)
Step 8 “Simultaneous Flash” – or –“Alternate Flash”
To flash all lamps synchronously, join all yellow wires together. This allows the lights to communicate with
each other.
To use alternate or “wig-wag” flash, identify lamps in “Group 1” and “Group 2”; Connect White wires in
“Group 1” to +12V.
NOTE: Optional Amber Turn Signal is disabled when Flashing Warning light is on.
NOTE: Activating the Back-up will disable the Warning light.
Step 9 (Optional) To use the optional “Mode 2” Flashing Warning pattern, a DPDT (double-pole, double-
throw) switch is required. See below diagram.

Page 4of 4
To access Secondary Mode, or second flash pattern, Connect Green to +12V and White to (-)Ground.
While in Mode 2, use Yellow wire (+12V) to program the desired flash pattern (step 7).
Mounting Instructions:
The light comes with 3 mounting screws and 3 mounting screw covers.
Utilizing the proper tools, secure the light with the 3 screws into place. Before tightening the screws fully,
ensure that the light is mounted with the 'TOP' indicator at the top of the light. Once the proper alignment
is achieved, fully tighten the 3 screws. Use caution when tightening these mounting screws as over-
tightening may break the lamp. With the screws tightened, press the mounting screw covers onto the
screw holes.
Warning: The plastic screw cover inserts are provided to make this lamp "tamper-resistant". They cannot
be removed once they are inserted. Do not insert them until the lamp is installed on the vehicle and
operation of the lamp is completely verified.
Note: Maxxima (a division of Panor Corp.) reserves the right to change any specifications, information and
instructions in this manual without notice. Panor Corp. makes no warranty of any kind with regard to this manual,
including but not limited to the proper and legal use and the fitness of this product for a particular purpose. Panor
Corp. shall not be liable for errors contained herein or for any incidental or consequential damages in connection with
the installation or use of this product as described in thismanual.