Mayline Tiffany Industries PERISCOPE ADJUSTABLE... User manual

(1)
** Denotes Color Code
~~Denotes Size
* Individual Items, Order by part number.
CA M Y LA ENII G UOR P AMO P YN
COMPONENTS
REF# QTY. DESCRIPTION PART NO.
1 1 Top CALL ~~**
2 4 Adjustable Leg 700242
3 2 Metal Stiffener 411270C** (72" Model only)
4A 4 Levelers or 700243
4B 4 Locking Caster 700244
HARDWARE BAG (Part No. 610217)
REF# QTY. DESCRIPTION PART NO.
E1 24 Screw, 1/4-20 x 1/2 7005 *
E2 20 Screw, #12-8 x 3/4 710232 *
When ordering components, specific color and/or size information may be required.
Contact a Mayline Customer Service Representative. 1-800-822-8037
NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.
ASSEMBLY INSTRUCTIONS
PERISCOPE ADJUSTABLE TABLE (4 Legs)
P/N
REV 02 9/06

COMPONENTS
REF# QTY. DESCRIPTION PART NO.
1 1 Top CALL ~~**
2 3 Adjustable Legs 700242
3 -- Metal Stiffeners --
4 3 Levelers or 700243
Locking Casters 700244
HARDWARE BAG (Part No. 610217)
REF# QTY. DESCRIPTION PART NO.
E1 24 (18 Used) Screw, 1/4-20 x 1/2 7005 *
E2 20 (0 Used) Screw, #12-8 x 3/4 710232 *
** Denotes Color Code
~~Denotes Size
* Individual Items, Order by part number.
When ordering components, specific color and/or size information may be required.
Contact a Mayline Customer Service Representative. 1-800-822-8037
NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.
ASSEMBLY INSTRUCTIONS
PERISCOPE ADJUSTABLE TABLE (3 Legs)
(2)

Fig. #1 Fig. #2
1. Begin assembly by placing the Top (1) face down on a clean flat work surface. Attach Legs (2) onto Top
using six Screws (E1) per leg. NOTE: Align the legs so that the height indicator marks located on the chrome
inner leg face outward toward the edge of the worksurface. Install all six Screws before tightening. Tighten all
screws. See Fig #1
2. Depending on the model ordered install either the Levelers (4A) or the Casters (4B).
3. Prior to setting table to the upright position, adjust all legs to the lowest positions. See Fig. #2. Begin by
lifting the outer portion of the leg to the full extended position. At this point the leg can be pushed down to the
lowest position. Repeat for all legs.
For 72" Models
4. Locate and position the two Stiffeners (E1) as shown in Fig #3. Locate the Stiffeners to the inside of the
legs and centered along the length of the top. Attach using twenty Screws (E2).
Height Adjustment Instructions
5. To adjust table to final desired height, position yourself at one end of the table and with one hand
(positioned in the center of the table) lift the end of table to approximate desired height. At the same time push
the black portion of the leg to the floor with the opposite hand. Repeat for all four legs. Note there are
numbers stamped on the chrome portion of the leg to assist in proper positioning of each leg.
6. To lower the table, lift the table and adjust the legs to the full extended position. This will allow the table to
be forced down to the lowest position. See Fig #4 above.
(3)

Floor glides may be used as levelers to accommodate uneven floors. However, tables with floor glides
MUST NOT be pushed, pulled or anyway slid along the floor. ALWAYS REMOVE any items on the table
and LIFT the table off the floor while moving.
Tables with Casters are not designed to be moved while the legs are extended with material on the table.
Doing so will result in damage to the casters, legs and fasteners in the top and WILL NOT be covered by
warranty. ALWAYS REMOVE any items on the table and lower the legs to the lowest position prior to
relocating the table.
WARNING
WARRANTY PARTS IDENTIFICATION NOT INCLUDED IN ASSEMBLY
REF# QTY. DESCRIPTION PART NO. NOTES
5 2 Extension Spacer 700245 * Use only when two legs have casters for wheelbarrow mobility.
(4)