MAYSER RADIOBAND 3G User manual
RADIOBAND 3G
RB3 T868
RB3 R868
USER'S MANUAL
Index
Important safet instructions.............................................................3
S stem usage.......................................................................................................3
INTRODUCTION..............................................................................4
Function..............................................................................................................4
Receiver RB3 R868 ............................................................................................5
RB3 T868 transmitter...........................................................................................6
INSPECTION AND MAINTENANCE...................................................7
1 Connect devices.................................................................................................7
2 Connect the receiver to the motor control.............................................................9
2.1 Setting the receivers / operating modes..................................................................10
2.2 ATEST Signal........................................................................................................11
3 Connect the safet edge to the transmitter (connection examples)………………….12
PROGRAMMING………………………………………………………..…13
4 Programming..........................................................................................13
4.1 MODE 1: Sa ety edge connected to IN1 activates R1...............................................14
4.2 MODE 2: Sa ety edge connected to IN1 activates R2...............................................15
4.3 MODE 3: Sa ety edge connected to IN1 activates R1 and R2....................................16
4.4 MODE 4: Sa ety edge connected to IN1 activates R1 and sa ety edge connected to IN2
activates R2.................................................................................................................17
CHECKING AND MAINTENANCE....................................................18
5 Does the equipment work properl ?...........................................................18
6 CHECK function ...................................................................................19
7 Troubleshooting.......................................................................................20
8 Total reset...............................................................................................21
9 Batteries ...............................................................................................21
Technical data summar ......................................................................................22
EU Declaration of conformit ...............................................................................24
Important safet instructions
!"#$!!%&" #&$!#' %%##!#(
#%!%)
*#'" $#!%"%'#+&$#(#,'( (%%"
#-$#,.
/0#!#,%&'-$!,+%&1%',$1
#!#' 1%)
/ &,,$%&1%%'1&-$%('!# 2!#"
$,'#'3"%'( #%'#')
/ #$(#$( -$!,,$%"&#, !(
$#)
/ (#-$&( ''&,'#(#&"&" 454
67#,#%&,)
• Follow all recommendations given in this manual to prevent serious danger to
people.
S stem usage
'"'%!'(#$" #'#)*''(#'#
( #')
,$($#### # ,3 !(( '
" $!##"##)
INTRODUCTION
Operating
''&,''(#,+8,,#%'*'$#%'#'
!!%" #(&'$')
&,!#'"#%&,#!%!#%1%##& &,
!#' (&% '###%!%)
##$$%&,# $(#,#') &,
!#(#,,!%( -$!,+%$'#',,$+#&9
')
: &,&$$!!#4+;< ,(&''%!%%"!"#
&,)''%%&&$%3#!'"3'# 43!$)=
%"%%1#(##'1&#')
: 1%''+ ''&,$#$!$(&+
( ###%&)
! ##,#!#$!$1' ##) ##"
$!$ ## 1' #%!%43#8
>#,%%&%'?)
The s stem complies with EN ISO 13849-1:2015, categor 2, PLd. Certified b TÜV
NORD CERT GmbH.
Receiver RB3 R868
@
Transmitter RB3 T868
5
ASSEMBLY AND
INSTALLATION
1 Installation of the equipment
9
4
2 Connecting the receiver to the control panel
Connecting the safet outputs to control panel.
Example: connection to control panel with safet contact / STOP input
Example: connection to control panel with input for safet edge 8k2
-$!,1' #%!%" !$(#(&'43#
'#%&(&!$#,%%&%'("#! %%#!
%)
&2(#A'$!$)
B
2.1 Adjustment of the receiver / Operating modes
ON Any change to the configuration of the switches requires
reprogramming of the system (see point 4, page 12).
OFF
Interference detector
SW1 9 -$!," '(&(#9#5@,)
5@,
Operating mode with optical safet edges
SW2 %#" ((" ,#, %(&'+
#' 1')
R3 function
SW3 C"
1#&
*%"1#&','+ #%&%'"
&( #,# $((%%(1#&)
*C,'+ #%&%'' &(
(&'#' ###)
%#,
ATEST signal polarit (depends on the control panel)
SW4 . %(2'A#D%
#%!%D,3 &, 3)
!. % '' ' "
#%!%,3A#D%)
*(!#" $%+#&"#3!"&)*#'#,!%&
" *<A4BEA.4(&'#'+&$,$ % &,)
A
2.2 ATEST signal
In order to compl with EN ISO 13849-1: 2015 safet standard, a signal to test the
s stem must be connected.
%%"'<,'1$ &#!#,%&) #',,$
'#&9')
*:<;,'+ %$'!"#$!''" !%(&
') #',,$'<,''" !%%,
#!"#'$!''")
AA
3 Connecting the safet edge to the transmitter
(connection examples)
A
IMPORTANT
The position of the
selector must
correspond to the
t pe of safet edge
connected.
IN 2 onl supports
8k2 resistive safet
devices and
mechanical / contact
devices.
The selector 3 is not
applicable if nothing
is connected to IN2.
PROGRAMMING
4 Programming
Working with one safet edge, ,$1'*A( #,#)*
'"#3)
1'"#3A>,'A?#>,'?#,$%$%&
#%&>,'?)
Working with two safet edges (mode 4), (&''*A
A' (&'*')
**%&, %1'#431'%%"')
(#!##,,+!% !%# '#'!)&$1-$
"%%#-$####'#!##,,)
# <F1$' %'$% '#','%')CG(#AH
"%%(% -$% ##!#,')
##four programming modes+'!' !$&$" $(
#,#' $!$#-$#' ##)
-$!,#,!##,,,''$#51(#!##,, (#
#,#+' ,#(# ( (%%"#,#)
A
4.1 MO E 1: Safety edge connected to IN1 activates R1
(&''*A"%%A)
,!%&'##,,#&IA#,#
Programming sequence:
#<F1$ ##>A?$%AC% >?)
#<F1$ #,#>?)
1! "%%1 #' ## ' #,# !#!#%&
!##,,'>?)
2!##,,,'+"(#'#!#<F1$
##)"1!"%%1 #')
A
4.2 MO E 2: Safety edge connected to IN1 activates R2
(&''*A"%%)
,!%&'##,,#&IA#,#
Programming sequence:
#<F1$ ##>A?$%C% >?)
#<F1$ #,#>?)
1! "%%1 #' ## ' #,# !#!#%&
!##,,'>?)
2!##,,,'+"(#'#!#<F1$
##)"1!"%%1 #')
A@
4.3 MO E 3: Safety edge connected to IN1 activates R1
and R2
(&''*A"%%A')
,!%&'##,,#&I#,#
Programming sequence:
#<F1$ ##>A?$%AC'C% >?)
#<F1$ #,#>?)
1!"%%1 #' ##' #,#!#!#%&
!##,,'>?)
2!##,,,'+"(#'#!#<F1$
##)"1!"%%1 #')
A5
4.4 MO E 4: Safety edge connected to IN1 activates R1 and
safety edge connected to IN2 activates R2
(&''*A"%%A'*"%%)
,!%&'##,,#&I#,#
Programming sequence:
#<F1$ ##>A?$%AC'C(% >?)
#<F1$ #,#>?)
1!"%%1 #' ##' #,#!#!#%&
!##,,'>?)
2!##,,,'+"(#'#!#<F1$
##)"1!"%%1 #')
A9
CHECKING AND
MAINTENANCE
5 Does the equipment work properl ?
(# (&#!" 1' #,#*
A'*+ *" 1#' !('
#,# 1##%&$ ##+ C ##>A'
?'% #,# $%'1(&#!1(()*(1 #C
!#,%&+ 3 (&#!" )
,$(# %!#( <F1$+ #,#" #&E
,'' $ C,!%%&(()&!# <F1$+
C##')
*(#,# 1$ ##+ CA' ##
#,!#,%&' (&#$>#%&A'?#!)
*(A" '((' ',+ 3 1%1"
##' ,##%)%,3$# 1,'
##%&$'##%&A'),##%2!4);< ,%'
1% $%' 1'8A'A'8): ,
#,%%&%' 1"8AJ8A'8J8)
&$,$$ 3($ 3 #',,$-$%&
1" #,#'##)>!,E 3($?)
A4
6 CHECK function
Ideal to know the radio coverage of the installation.
# ##K868;1$(#%A'# 3,')
'#% "%%,'($#1!"%%1 #')
#(#,,!%'#!'%,$#)$# &, 3
1!"%%1 #'#&A+@')*(&$ #'& #$%
'( ,$#+ &,"#3!#!#%&)*('$# #(+
,,$" #,#(%# ,,$!#+ ##,
#$1!' ###$##')
#%% (&'%%''" (%')
C"%##1#&$,!)
28 3,'+!# 868;1$#"@,$)<2 3,'+
$1!"%%1 #'' '#% "%%(% $$%&
((%$#)
*#,,''!#(#,868;($ '( %%!#
$#!#!#&,!#)
AB
7 Troubleshooting
This manual suits for next models
2
Table of contents
Other MAYSER Safety Equipment manuals
Popular Safety Equipment manuals by other brands
Petzl
Petzl Laser TECHNICAL NOTICE
Guardian Fall Protection
Guardian Fall Protection Cable LE Lanyard instruction manual
WaterWarden
WaterWarden SAFETY COVER Installation & maintenance manual
Viraj
Viraj SF-FBH(WPB02)A-1057 User instructions
Guardian Fall Protection
Guardian Fall Protection GR11 Web SRL instruction manual
Wieland
Wieland SLX-COLM Series Mounting instructions
Cardinal Gates
Cardinal Gates Extra Tall Premier Pressure Gate XTPPG Assembly instructions
Scott
Scott PROFLOW FH22 Installation and use instructions
MSA
MSA PrimaX IR quick start guide
SECUMAR
SECUMAR MYSTIC 150 instructions
Millenium
Millenium M-007-SL LOCK-ON TREESTAND instruction manual
3M
3M Dustmaster 021-00-38P Care and maintenance