Maytronics Dolphin Classic 12 User manual

User Instructions
EN
8180030
Maytronics Dolphin robotic pool cleaner
CLASSIC 12 / CLASSIC 12+

1
CLASSIC 12 / CLASSIC 12+ |User Instructions
CLASSIC 12 / CLASSIC 12+
Robotic Pool Cleaner
User Instructions
EN
Contents
1. INTRODUCTION ......................................................................................................................................................2
2. SPECIFICATIONS .....................................................................................................................................................2
3. WARNINGS AND CAUTIONS ..............................................................................................................................2
4. ROBOTIC POOL CLEANER PARTS ................................................................................................................... 4
5. USE THE POOL CLEANER....................................................................................................................................5
5.1 Setup ..................................................................................................................................................................5
5.2 Place the Pool Cleaner in the water................................................................................................... 6
5.3 Robot Indicator Lights............................................................................................................................... 6
5.4 Remove the Pool Cleaner from the water .......................................................................................7
6. USE THE
MyDolphin™ Plus IOT MOBILE APP............................................................................................. 8
6.1
Getting Started with the MyDolphin™ Plus App ............................................................................... 8
6.2
Prepare the Pool Cleaner for Connection .......................................................................................... 8
6.3
Activate the Pool Cleaner Using your Mobile Smart Device ....................................................... 8
6.4
Led Lights ........................................................................................................................................................ 9
7. OFFSEASON STORAGE....................................................................................................................................... 9
8. CLEANING THE DUAL FILTER BASKET..........................................................................................................10
8.1
Cleaning after use - removing and cleaning the dual filter basket .........................................10
8.2
Periodic filter cleaning ...............................................................................................................................11
8.3
Clean the Impeller ...................................................................................................................................... 12
9. TROUBLESHOOTING ........................................................................................................................................... 13
10.
MyDolphin™ Plus - TROUBLESHOOTING....................................................................................................14

2CLASSIC 12 / CLASSIC 12+ |User Instructions
1. INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner.
We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and
cost-effective pool cleaning.
Its reliable filtration in all pool conditions, active brushing, and all-surface climbing brush enhance
maximum pool hygiene.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technology, long lasting
performance and easy maintenance. You and your family will be free to enjoy swimming with full
confidence that your pool is completely clean.
2. SPECIFICATIONS
Robot
Motor protection: IP 68
Minimum depth: 0.4m / 1.33ft
Maximum depth: 5m / 16.4ft
This product is in accordance with EU Regulation & Directive 2014/531EU.
For full information, please contact us at www.maytronics.com/contact-us-en and ask for the EC
declaration of conformity.
3. WARNINGS AND CAUTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
Please adhere strictly to the following WARNINGS:
Ensure the electrical outlet is protected by a Ground Fault Interrupter (GFI) or an Earth Leakage
Interrupter (ELI).
Keep the power supply out of standing water.
Position the power supply at least 3.5m/12ft away from the edge of the pool.
Do not enter the pool while the Pool Cleaner is in the water.
Unplug the power supply before servicing.
Take the Robot Pool Cleaner out of the pool before allowing people to enter the pool.
When examining the Robot Pool Cleaner, disconnect the main power supply.
Ensure that children do not attempt to access Robot Pool Cleaner while it is operating.
Digital switch-mode power supply
IP 54
Input: 100-125 AC Volt, 200-230 AC Volt, 50-60Hertz, 120 Watt
output: <30 VDC
Bluetooth®/Wifi® Max tras power 10mW EIRR, 2,4 GHz frequency
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING

3
CLASSIC 12 / CLASSIC 12+ |User Instructions
Keep the Robot Pool Cleaner out of the reach of children or persons with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction.
The unit must be connected only to a supply circuit that is protected by a ground-fault circuit
interrupter (GFCI). This GFCI should be tested on a routine basis. To test the GFCI, push the test
button. The GFCI should interrupt power. Push the reset button. Power should be restored. If
the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the
power unit without the test button being pushed, a ground current may be flowing, indicating
the possibility of an electric shock. Do not use the power unit. Disconnect the power unit and
contact the manufacturer for assistance.
Only an original power cable must be used, at all times. Replaced by a Robot Pool Cleaner
certified technician, in case of need to avoid hazard.
To reduce the risk of electric shock replace damaged cord immedietely.
Do not use extension cord to connect unit to electric supply; provide a properly located outlet.
Use the originally supplied power supply only
Please ensure that the following PRECAUTIONS are implemented:
Operator should keep hands away from driving belt mechanism.
Position the Caddy and power supply at least 3.5m/12ft from pool’s edge – during operation.
For continued protection against possible electric shock, the power supply unit should be placed
at least 11cm/4in above ground.
When lifting the Robot Pool Cleaner, take care to prevent back injury.
Do not bury cord – locate cord to minimize abuse from lawn mowers, hedge trimmers and other
equipment.
When not in use, store the Pool Cleaner on its Caddy in a shaded area. Use the Pool Cleaner in the following
water conditions only.
Chlorine Max 4 PPM
pH 7.0-7.8 PPM
Temperature 6-35°C / 43-95°F (below 15°C / 59°F climbing performance may be affected)
NaCl Maximum = 5000 PPM
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
WARNING
WARNING
WARNING
WARNING
WARNING

4CLASSIC 12 / CLASSIC 12+ |User Instructions
Caddy kit
Power supply
Robotic Pool Cleaner Model Classic 12 / Classic 12+
Filtration options
4. ROBOTIC POOL CLEANER PARTS

5
CLASSIC 12 / CLASSIC 12+ |User Instructions
5. USE THE POOL CLEANER
5.1 Setup
The Pool Cleaner is very simple to use. Simply place it in the pool and make sure that it is correctly
positioned on the floor of the pool.
Turn it ON and enable it to complete the task.
Before using the Pool Cleaner for the first time, perform the following steps:
Position the power supply
so that it is approximately in the
middle of the long side of the
pool at a distance of 3.5m/12ft.
Unwind the blue cable and stretch it out completely so that it
has no kinks.
3.5m/12ft
5.1.1 5.1.2
Attach the blue cable to the power supply by
inserting it with the notch on the connector (1) lined
up to the groove in the socket on the power supply.
Turn it clockwise (2).
Plug in the power supply
and leave it in the OFF position.
5.1.45.1.3
1
2

6CLASSIC 12 / CLASSIC 12+ |User Instructions
5.2 Place the Pool Cleaner in the Water
Place the Pool Cleaner into the pool.
Release the Pool Cleaner and let it sink to the
floor of the pool. Make sure that the blue cable is
free of any obstructions.
5.2.1
Turn the power supply ON.
The Pool Cleaner will now operate until it has
reached the end of the cleaning cycle.
5.2.2
Light Indication
Blue blinking Normal operation (additional options available in the App)
Green blinking Smartphone communication with Pool Cleaner – manual driving navigation
5.3 Robot Indicator Lights - For eligible models only
5.3.1
ON
Indicator lights.

7
CLASSIC 12 / CLASSIC 12+ |User Instructions
Using the blue cable, bring the Pool Cleaner to the pool edge.
Use the handle to remove the Pool Cleaner from the pool.
Place the Pool Cleaner on the edge of the pool to let the water drain out.
5.4.3
5.4.2
5.4 Remove the Pool Cleaner from the Water
5.4.1
Turn OFF the power supply.
Please use the cable to pull the robot to the surface, then use the handle.
WARNING
WARNING

8CLASSIC 12 / CLASSIC 12+ |User Instructions
6. USE THE MyDolphin™ Plus IOT MOBILE APP
Please download the Maytronics MyDolphin™ Plus app to your mobile smart device from either Google Play
for Android or the Appstore for iOS.
The Maytronics MyDolphin™ Plus app is cloud-connected, enabling control from anywhere at anytime,
with real-time connectivity.
6.1 Getting Started with the MyDolphin™ Plus App
The app is compatible with the following smart devices:
· Apple (iOS) – version 10 and up – iPhone, iPad, iPod
· Android – version 5 and up operating system
1. Make sure your mobile smart device (phone/tablet) is connected to your home/pool Wi-Fi® network.
2. Make sure you have your Wi-Fi® network name and password in reach.
3. Ensure Bluetooth® is enabled on your smart device.
4. Android users - please make sure your GPS and Location Services are ON.
5. For iOS 13 only - while the app is working, enable Bluetooth® & location.
6. Please make sure your router is on 2.4Ghz Wi-Fi® frequency only.
6.2 Prepare the Pool Cleaner for Connection
1. Connect the Pool Cleaner to the power supply.
2. The connectivity LED light indicator on your power supply will start flashing blue.
3. Place the Pool Cleaner in the water.
4. Press the ON button on your IoT power supply, to start the Pool Cleaner.
6.3 Activate the Pool Cleaner Using your Mobile Smart Device
1. Activate the MyDolphin™ Plus app.
2. Click Agree and allow all the required permissions.
3. Sign up by creating an account or use your Gmail/Facebook accounts.
4. Scan the QR code located on the side of the power supply.
5. Alternatively, press "Search for your robot manually" to pair with your Pool Cleaner.
The app will start pairing with your power supply.
6. Wait for the steady blue connectivity LED light and a success message in the app.
7. Connect to your home/pool Wi-Fi® network.
8. Enter the password of your home Wi-Fi® network, and press CONTINUE
After a short while, your power supply will flash green and blue.
9. Wait for the steady green connectivity LED light and a success message in the app.
NOTE: Please make sure to fill in the Warranty details and name your Dolphin Pool Cleaner.

9
CLASSIC 12 / CLASSIC 12+ |User Instructions
6.4 LED Lights
Connectivity LEDs
The connectivity LED light on the power supply has several modes:
1. Flashing blue light - waiting for Bluetooth® connection.
2. Steady blue light - connected via Bluetooth®.
3. Flashing green light - power supply is trying to connect to your home/pool Wi-Fi® network and
cloud, or a weak internet signal.
4. Steady green light - power supply is now connected to the Wi-Fi® network and to the cloud.
5. Alternating blue and green light - power supply is connected via Bluetooth® and trying to connect
to your home/pool Wi-Fi® network & cloud.
On/Off LEDs
1. Flashing green light - waiting for the next operation (delay mode or weekly timer).
2. Alternate blue/green/red lights – program updating remotely.
Please wait until process is completed.
3. Steady red light – fault. Refer to troubleshooting.
Tips
• If the app is stuck on the same screen for over 2 minutes, close the app and re-open it.
• To test your Wi-Fi® signal strength and quality, play a video via your smart device browser.
7. OFF SEASON STORAGE
If the Pool Cleaner will not be in use for an extended period, perform the following storage steps:
1. Make sure that no water is left in the Pool Cleaner.
2. Thoroughly clean the filter basket and insert them in place.
3. Roll up the cable so that it has no kinks and place on the Caddy.
4. Store the pool cleaner upright on the Caddy in a protected area out of direct sun/rain/frost at a
temperature of between 5˚-45˚C / 41˚-113˚F.