Maytronics Pulit E70 User manual

1English
8151148
by
Pulit E70 Robot Pool Cleaner by Maytronics
EN
FR
IT
User Instructions
Guide d’utilisation
Istruzioni per l’uso
Instrucciones para el Usuario
Bedienungsanweisungen
SP
DEU

3English
What You’ll Find Inside the Box
Part X Comment
Base frame for filter elements 2
Ultra-fine filter 4 filters
Bag for filters storage 1
Ultra-fine disposable filter with frames 1 set 10 disposable filters per set
Spring filter 4 filters
“S” clip 4
Power supply unit 1
Pulit E70 pool cleaner 1
Caddy kit 1
Optional components available on request from your Pulit E70 distributor
Section 1 - Description of Main Components
1. Filters
There are three types of filters.
Spring filter + base frame
For dirty pools with large debris such as
leaves etc. – Useful for beginning of season.
Ultra-fine filter cartridge + base frame
For day-to-day use.
Factory default.
Ultra-fine disposable filter + frame
For day-to-day use for up to 3 cycles.
2. Brushes
There are three types of optional brushes, each designed to provide optimal traction on different pool surfaces. Only one type set is
provided with your Pulit E70.
Standard Brush
For concrete, PVC, fiberglass and liner.
Combined Brush
For rough ceramic surface and mosaic tiles.
Wonder Brush
For smooth ceramics.
Power supply Unit
Pulit E70 pool cleaner
Filter and cartridges

4
English
3. Power supply unit
Digital, “Switch-Mode” power supply:
Input - 100-250 AC VoltsUÊ
50-60 HertzUÊ
180 WattUÊ
Output - 30 VDCUÊ
IP 54UÊ
Section 2 – Pulit E70 Operation
Part 1 – Preparing the Pulit E70 Pool Cleaner for Use
A. Assemble the Caddy kit – you will find the instructions in a separate document
B. Adjusting the handle float angle
The handle angel must be adjusted to determine the speed that the Pulit E70 advances along the water-line.
1. Lay the handle down at an angle of 180º to
the ground.
2. Push the base of the arm into the body of the
Pulit E70 and slide it towards the rear of the
Pulit E70 until it clicks into the required position.
Normal advance
More efficient cleaning action on water-line.
Fast advance
Fast speed – For faster but less efficient cleaning
action on water-line.
Push in here Slide here
Push in here
Slide here
ON
On/Off
switch

5English
C. Laying out the cable
Unwind minimal required cable to cover the entire pool size, straight the cable along the pool side.
Make sure there are no twists or kinks.
Part 2 - Into the water
Inserting the Pulit E70 into the pool.
Place the Pulit E70 into the pool and release the handle.
Note: When using the Combined brushes or Wonder brushes, gently squeeze the Wonder brush material until it is totally wet.
Only use the original supplied power supply unit.
The Power supply unit is splash proof – do not immerse it in water.
Unplug the power supply unit before any servicing activity.
Do not plug the power supply unit in before placing the pool cleaner in the water.
Ensure the mains outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI).
3 Meters
10 feet Swivel

6
English
Turning the Pulit E70 on
Part 3 - Taking the Pulit E70 out of the water
Unplug power supply before any servicing activity.
If the Pulit E70 has not finished its cycle, turn off the power supply1.
unit and unplug the mains.
Pull the floating cable gently until the Pulit E70 has risen to the2.
surface, then lift by the handle.
Plug the floating cable from the Pulit E701.
into the power supply unit.
Plug the electrical cable from the power2.
supply unit into the mains.
Press the ON/OFF switch3.
The Pulit E70 will now start to work.4.
Important: Do NOT lift the Dolphin from the water by its cable.
Floating cable
ON
On/Off
switch
Note : If your model includes the remote control unit, please refer to the included instruction leaflet.

7English
Section 3 - Routine Maintenance
Part 1 - Extracting and cleaning the filter elements
Unplug power supply before any servicing activity.
Reassembling the filter elements
Insert the locating tabs at the bottom of the
filter element into their groves on the base frame,
then close the “S” clip.
Opening the Ultra-fine disposable filters
1. Open the filter frames by unclipping the
fasteners at the sides.
2. Rinse out the cartridge base, then reassemble
the cartridges with a new disposable filter.
Filter frame
Cartridge base
Side fastener
Locating tab
Locating tab groove
Disposable
Ultra-fine filter element
23
1

8
English
Reinstall the filters according to the diagram
DO NOT FORCE THE FILTERS INTO PLACE.
Part 2 - Dismantling and cleaning the impeller
Unplug power supply before any servicing activity.
Dismantle the impeller cover and
clean around the impeller housing,
then reassemble.
Grooved end fitting Octagonal end fitting
Important: Where applicable, you must reset the full filter bag indicator on the power supply unit.
Important: When storing a Pulit E70 with Combined or Wonder brushes, please note to keep the brushes wet at all times.
Recommendation: Rinse all brushes with clean water after each cleaning cycle.
Coil the cable and store in dry cool area – preferably on the Caddy if available.
Do NOT store the Pulit E70 exposed to direct sunlight.
Do NOT store the Pulit E70 exposed to excessive heat.
Do NOT store the Pulit E70 exposed to frost.
Section 4 – Storage Advice
23
1

9English
Troubleshooting Guide
Before contacting your Pulit E70 distributor please read through this guide.
The pool water condition must be within the following parameters:
PH: 7.0 – 7.4 Salt: Max 5,000 ppm
Temperature: 12˚C(54˚F) to 32˚C(90˚F) Chlorine: Max 2 ppm
Symptom Solution
Cable twisting or cable coils up Check for any obstruction in the pool
Change handle diagonal position after each use
Remove excess cable from the pool
Make sure filter cartridge is clean
Straighten cable and lay it in the sun periodically
Pulit E70 is moving in circles or does not reach all pool areas or
the Pulit E70 is not traveling sideways on walls
Check for foreign objects in moving parts
Make sure Filter elements are clean and that the filter doors
are closed
Make sure that there is enough cable laid out to cover the
whole pool
Before using the Pulit E70 at the beginning of the season you
should brush any algae from the floor and walls of the pool
Adjust the diagonal angle of the handle
Pulit E70 does not climb walls Make sure the filter cartridge is clean
If using the Pulit E70 at the beginning of the season, use the
spring cartridge
If using the Pulit E70 at the beginning of the season you should
first brush any algae from the floor and walls of the pool
Check if brushes are suitable for pool coating and replace them
if necessary
Check if brushes are worn and replace them if necessary
Make sure the impeller area is clean
When applicable: Check that the RCU is set for climbing
Pulit E70 not sinking Make sure the Wonder brushes or the combined brushes are
soaked in water
Pulit E70 disengaging from wall at water line If Pulit E70 climbs too high consult your Pulit E70 distributor
RCU is not working When applicable: Check if the batteries need replacing
Motor is not working Check if the impeller is blocked
Check if the drive system is blocked
Electrical problem (power supply), check power source.
If power source is in order, please contact your Pulit E70
distributor
Additional troubleshooting is available at our Website:
http://www.maytronics.com

10
French
Liste des pièces fournies dans l’emballage
Pièces X Remarques
Châssis des composants du filtre 2
Filtre ultrafin 4 filtres
Poche de rangement des sacs filtres 1
Filtre jetable ultrafin avec châssis 1 lot 10 filtres jetables par lot
Filtre pour nettoyage de printemps 4 filtres
crochet en “S” 4
Bloc d’alimentation 1
Robot nettoyeur de piscine Pulit E70 1
Kit Caddy 1
Les éléments optionnels sont disponibles sur demande de la part de votre
distributeur Pulit E70
Chapitre 1 - Description des principaux composants
1. Filtres
Trois types de filtres sont disponibles.
Filtre Printemps (pour nettoyage de
printemps) + châssis
Pour piscines sales contenant des saletés de
grande taille, par ex. des feuilles – utile en
début de saison.
Cartouche de filtre ultrafin + châssis
A usage quotidien.
Réglage d’usine, défini par défaut.
Filtre jetable ultrafin + châssis
A usage quotidien, conçu pour 3 cycles.
2. Brosses
Trois types de brosses sont proposés en option, chacune d’elles étant conçue pour fournir une traction optimale sur différentes sur-
faces de piscine. Un seul ensemble brosse est fourni avec votre nettoyeur Pulit E70.
Brosse standard
pour surfaces en béton, PVC, fibre de verre
et à revêtement.
Brosse combinée
pour surface rugueuse en céramique et
pavés en mosaïque.
Brosse Wonder
pour sols en céramique lisse.
Bloc d’alimentation électrique
Robot nettoyeur de piscine
Pulit E70
Filtre et cartouches