McFarlane QUADRA-TILL 200 Series Guide

Operation and Parts
Manual
Version: 12256 — Serial Numbers 20309 - 20900
Read and understand the manual. This manual provides information
and procedures to safely operate and maintain the Quadra-Till.
SIZES, SHATTERS, MIXES, & LEVELS
MFG. CO.INC.
MADE IN THE USA
200 Series

888-627-8569 3 Quadra-Till from McFarlane Mfg.
Contents
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Contact Information . . . . . . . . . . . . . . . . 5
SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General . . . . . . . . . . . . . . . . . . . . . . 5
Safety Alert Symbols. . . . . . . . . . . . . . . . 6
Safety Icons Nomenclature . . . . . . . . . . . . 7
Personal Protection/Important Information . 7
Prohibited Actions . . . . . . . . . . . . . . 7
Hazard Avoidance . . . . . . . . . . . . . . 7
General Operating Safety . . . . . . . . . . . . . 8
Towing Safety . . . . . . . . . . . . . . . . . . . 8
Operation Safety . . . . . . . . . . . . . . . . . . 8
Assembly Safety . . . . . . . . . . . . . . . . . . 8
Maintenance Safety . . . . . . . . . . . . . . . . 8
COMPONENT NOMENCLATURE . . . . . . . . . . . . . . . 9
Component Locations . . . . . . . . . . . . . . . 9
Component Description . . . . . . . . . . . . . . 9
Disk Gangs (1) . . . . . . . . . . . . . . . 9
Chisel Shanks (2) . . . . . . . . . . . . . . 9
Rear Leveler Disk Attachment (3) . . . . . . 10
Four-Bar Harrow (4) . . . . . . . . . . . . . 10
QT-213F Disk Gang and Leveler Disk Toolbar. . . 10
QT-215F and QT-217F Disk Gang
and Leveler Disk Toolbar. . . . . . . . . . . . . . 11
Disk Gang Gauge Wheels (215F and 217F). . . . 11
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hydraulic Requirements . . . . . . . . . . . . . . 11
Number of Shanks. . . . . . . . . . . . . . 11
Horsepower Range . . . . . . . . . . . . . 11
Tillage Depths . . . . . . . . . . . . . . . . 11
Tongue Weight . . . . . . . . . . . . . . . 11
Overall Weight (GVWR) . . . . . . . . . . . 11
Transport Width . . . . . . . . . . . . . . . 11
Working Tillage Width (Cut Width) . . . . . 11
Towing Speed . . . . . . . . . . . . . . . . 11
Instructions for Display of Hazard
and Informational Signs . . . . . . . . . . . . . . 12
ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
TOWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Safety . . . . . . . . . . . . . . . . . . . 14
Safety Chain. . . . . . . . . . . . . . . . . 14
Bystanders . . . . . . . . . . . . . . . . . 14
Towing and Maximum Towing Speed . . . . 14
Highway and Transport Operations . . . . . . . . 14
Pre-towing Checklist . . . . . . . . . . . . . . . . 15
HOOK-UP TO TRACTOR . . . . . . . . . . . . . . . . . . . . . 16
Safety . . . . . . . . . . . . . . . . . . . . . . . 16
Prior to Connecting Unit . . . . . . . . . . . 16
Tow Chain . . . . . . . . . . . . . . . . . . 17
Connecting to the Tractor . . . . . . . . . . . . .17
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Safety . . . . . . . . . . . . . . . . . . . . . . . 20
Initial Setup . . . . . . . . . . . . . . . . . . . . 20
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Safety . . . . . . . . . . . . . . . . . . . . . . . 27
Tire and Lug Torque Specifi cations . . . . . . . . 28
Bolt Torque Chart . . . . . . . . . . . . . . . . . 28
Maintenance Schedule . . . . . . . . . . . . . . 28
Lubrication . . . . . . . . . . . . . . . . . . . . . 28
Wheel Bearings . . . . . . . . . . . . . . . 28
Lubrication Points . . . . . . . . . . . . . . 28
Hydraulic Components. . . . . . . . . . . . . . . 30
Safety . . . . . . . . . . . . . . . . . . . . 30
Wheel Lift Cylinders, Disk Gang,
and Leveler Disk Wing Cylinders . . . . . . 30
Rear Disk Leveler Cylinders. . . . . . . . . 30
Tire Safety . . . . . . . . . . . . . . . . . . . . . 30
Disk Gang Disks . . . . . . . . . . . . . . . . . . 31
Front Disk Gang Coil Spring System . . . . . . . 31
Chisel Shank Spring Replacement . . . . . . . . 32
Chisel Shank Point/Shovel Replacement . . . . . 32
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . 33
STORAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Safety . . . . . . . . . . . . . . . . . . . . . . . 34
Placing Into Storage (Disk Coatings) . . . . . . . 34
DISPOSAL OF EQUIPMENT AT END
OF USEFUL LIFE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PARTS SECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ordering Parts . . . . . . . . . . . . . . . . . . . 34
Dealer Contact Information . . . . . . . . . . . . 34
Decals . . . . . . . . . . . . . . . . . . . . . . . 34

Quadra-Till from McFarlane Mfg. 4 888-627-8569
PARTS DRAWINGS . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Hitch Frame Assembly . . . . . . . . . . . . . . . 36
Main Frame Assembly . . . . . . . . . . . . . . . 38
QT-215F and QT-217F Chisel Frame . . . . . . . 40
Disk Gang Frame Assembly (QT-207 - QT-213F) . 41
QT-215F and QT-217F Disk Frame . . . . . . . . 42
Disk Gang Mounting Hardware . . . . . . . . . . 43
Disk Gang Assembly (All Models) . . . . . . . . . 44
Folding Disk Mount Tube Assembly
(Model QT-213F Rear Only) . . . . . . . . . . . . 46
Independent Disk Blades . . . . . . . . . . . . . 47
Axle Frame Assembly . . . . . . . . . . . . . . .48
Spindle and Hub . . . . . . . . . . . . . . . . . . 50
Spindle and Hub (Continued) . . . . . . . . . . . 51
Chisel Shank Assembly . . . . . . . . . . . . . . 52
Leveler Disk Frame Arms . . . . . . . . . . . . . 53
Leveler Disk Assembly. . . . . . . . . . . . . . .54
Leveler Disk Frame (QT-207, 209, 211, and 213) . 55
Leveler Disk Frame
(QT-213F, QT-215F, and QT-217F) . . . . . . . . 56
4-Bar Harrow Lift Arm Assembly . . . . . . . . . . 58
4-Bar Harrow Sections. . . . . . . . . . . . . . .59
3-Bar Harrow Lift Arm Assembly . . . . . . . . . . 60
3-Bar Harrow Sections. . . . . . . . . . . . . . .61
Rolling Basket Assembly. . . . . . . . . . . . . . 62
Main Lift Depth Stop Assembly . . . . . . . . . . 63
Lighting and Wiring Harness. . . . . . . . . . . . 64
Wheel Cylinder Hydraulics. . . . . . . . . . . . . 65
Leveler Disk Hydraulics . . . . . . . . . . . . . . 66
Disk Gang Hydraulics . . . . . . . . . . . . . . . 67
Hydraulic Diagram for QT-213F
Wing Fold Cylinders . . . . . . . . . . . . . . . . 68
Hydraulic Diagram for QT-215Fand QT-217F
Wing Fold Cylinders . . . . . . . . . . . . . . . . 69
CHISEL SHANK LAYOUT DIAGRAM . . . . . . . . . . . 70
QT-207 - Shank Frame . . . . . . . . . . . . . . 70
QT-209 - Shank Frame . . . . . . . . . . . . . . 71
QT-211 - Shank Frame. . . . . . . . . . . . . . . 72
QT-213 - Shank Frame . . . . . . . . . . . . . . 73
QT-213F - Shank Frame . . . . . . . . . . . . . . 74
QT-215F - Shank Frame . . . . . . . . . . . . . . 75
QT-217F - Shank Frame . . . . . . . . . . . . . . 76
ROLLING BASKET LAYOUT DIAGRAM. . . . . . . . . 77
QT-207 - Rolling Basket Layout . . . . . . . . . . 77
QT-209 - Rolling Basket Layout . . . . . . . . . . 77
QT-211 - Rolling Basket Layout . . . . . . . . . . 78
QT-213F - Rolling Basket Layout . . . . . . . . . 78
QT-215F - Rolling Basket Layout . . . . . . . . . 79
QT-217F - Rolling Basket Layout . . . . . . . . . 79
INDEPENDENT DISK BLADE
LAYOUT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . 80
QT-209-I Layout . . . . . . . . . . . . . . . . . . 80
QT-211-I - Layout . . . . . . . . . . . . . . . . . 80
QT-213F-I Layout . . . . . . . . . . . . . . . . . 81
QT-215F-I Layout . . . . . . . . . . . . . . . . . 81
QT-217F-I Layout . . . . . . . . . . . . . . . . . 82
DEALER CONTACT INFORMATION . . . . . . . . . . . . 83
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Limited Warranty Statement . . . . . . . . . . . . 83
Serial Number Location . . . . . . . . . . . . . .83
Warranty Registration Form
and Inspection Report . . . . . . . . . . . . . . . 85

888-627-8569 5 Quadra-Till from McFarlane Mfg.
Introduction
Thank you for purchasing the McFarlane Quadra-Till
Primary Vertical Tillage System. We know that you
will get many years of dependable service because
McFarlane has been manufacturing quality agricultural
equipment since 1936.
A single pass in the fall with the Quadra-Till will leave the
soil and residue in a condition that requires only a light
pass with a Reel Disk or vertical tillage tool. Using both
implements will create the perfect seedbed, saving time,
expense, and preparing your fi elds for spring planting.
The Quadra-Till incorporates fi eld residue up to a ten inch
depth for quick breakdown and nutrient deposit. It also
prepares the soil so spring fi eld preparation and planting
can be done quicker and easier. The Quadra-Till also
prepares the ground to promote strong root growth for
higher yields.
Quadra-Till provides four tillage functions in a single fi eld
pass.
1. Size Residue – Cuts residue into small pieces for
faster breakdown.
2. Shatter Soil – Full width fracture of the soil to
eliminate compaction layers.
3. Mix Residue – Spreads residue uniformly throughout
the profi le, ensuring good seed to soil contact in the
spring.
4. Levels the Seedbed – Eliminating the need for
multiple fi eld fi nishing passes.
Contact Information
If you have questions not answered in this manual,
require additional copies, or the manual is damaged,
please contact your local dealer or:
McFarlane Mfg. Co., Inc.
1330 Dallas Street
P.O. Box 100
Sauk City, WI 53583
Phone: [phone]
Toll Free: [phone]
Fax: [phone]
E-mail: info@fl exharrow.com
Web: www.fl exharrow.com
Safety
General
Safety of the operator and bystanders is one of the main
concerns in designing and developing a new piece of
equipment. Designers and manufacturers build in as
many safety features as possible. However, every year
many accidents occur which could have been avoided by
a few seconds of thought and a more careful approach to
handling the equipment.
Most work related accidents are caused by failure to
observe basic safety rules or precautions. An accident
can often be avoided by recognizing potentially
hazardous situations before an accident occurs. As you
assemble, operate, tow, or maintain the Quadra-Till (unit),
you must be alert to potential hazards. You should also
have the necessary training, skills, and tools to perform
any assembly or maintenance procedures.
Improper operation and maintenance of this unit could
result in a dangerous situation that could cause injury or
death.
WARNING
Do not use or tow the unit until you read and
understand the information contained in this
manual.
Safety precautions and warnings are provided
in this manual and on the unit. If these hazard
warnings are not heeded, bodily injury or death
could occur to you or to other persons.
McFarlane cannot anticipate every possible circumstance
that might involve a potential hazard. The warnings
in this manual and on the product are, therefore, not
all-inclusive. If a method of operation not specifi cally
recommended by us is used, you must satisfy yourself
that it is safe for you and for others. You should also
ensure that the unit will not be damaged or be made
unsafe by the methods that you choose.
The information, specifi cations, and illustrations in this
manual are based on the information that was available
at the time this material was written and can change at
any time.

Quadra-Till from McFarlane Mfg. 6 888-627-8569
Safety Alert Symbols
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
This manual contains DANGERS, SAFETY
INSTRUCTIONS, CAUTIONS, IMPORTANT NOTICES,
and NOTES which must be followed to prevent the
possibility of improper service, damage to the equipment,
personal injury, or death. The following key words call the
readers attention to potential hazards.
Hazards are identifi ed by the “Safety Alert Symbol”
and followed by a signal word such as “DANGER”,
“WARNING”, or “CAUTION”.
DANGER
Indicates an imminently hazardous situation which,
if not avoided, will result in death or serious injury.
This signal word is limited to the most extreme
situations.
WARNING
Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
NOTICE
Indicates that equipment or property damage can result if
instructions are not followed.
SAFETY
INSTRUCTIONS
Safety instructions (or equivalent) signs indicate
specifi c safety-related instructions or procedures.
NOTE: Contains additional information important to
a procedure.

888-627-8569 7 Quadra-Till from McFarlane Mfg.
Safety Icons Nomenclature
This manual and the equipment
has numerous safety icons. These
safety icons provide important
operating instructions which alert
you to potential personal injury
hazards.
Personal Protection/Important
Information
Read the manual
Maintenance procedure
Crush hazard
Eye protection
Hand protection
Head protection
Hearing protection
Inspect equipment
OEM
OEM
OEM parts only
Place in neutral
Protective shoes
Remove key
Damaged hazard label
Set parking brake
Slow vehicle placard
STOP Stop engine
Support stand usage
Use proper tools
Visually inspect
Prohibited Actions
Do not alter or modify
Do not leave out tools
Do not weld
No alcohol
No children
No drugs
No open flame
No passengers
No riders
No smoking
Hazard Avoidance
Block wheels
Crushing hazard (body)
Crush hazard (foot)
Crush hazard (rolling over)
Defective or broken part
Entanglement hazard
Explosive separation hazard
Falling hazard
Fire hazard
High-pressure fluid hazard
Hose damage
Hot surface
Maintain safe distance
Overturn hazard
Pinch point hazard
Pressure alert / check
pressure
Projectile hazard
Safety alert symbol
Sharp object hazard
Slipping injury
Tripping injury
0Zero pressure

Quadra-Till from McFarlane Mfg. 8 888-627-8569
General Operating Safety
WARNING
Read And Understand Manual
To prevent personal injury or even death, be
sure you read and understand all of the
instructions in this manual and other related OEM
equipment manuals! This equipment is dangerous to
children and persons unfamiliar with its operation.
The operator should be a responsible adult familiar
with farm machinery and trained in this equipment’s
operations. Do not allow persons to operate or
assemble this unit until they have read this manual
and have developed a thorough understanding of the
safety precautions and how it works.
This unit was designed for a specifi c application; DO
NOT modify or use this unit for any application other
than which it was designed.
Units operated improperly or by untrained personnel
can be dangerous!
N
I
NG
AR Hazard And Information Signs
Replace any missing or hard-to-read decals.
Decal placement and part numbers can be
found in the Nomenclature section of this manual.
Damaged Parts Hazard
Do not use this unit if it is in need of repair.
If you believe the unit has a defect which
could cause damage, injury, or death, you should
immediately stop using the unit.
Fall Hazard
Do not use the unit as a work platform.
Do not stand on top of the unit at any
time. Do not ride on the unit or allow others to ride
on it.
Entanglement Hazard
Do not wear loose fi tting clothing which may
become entangled in moving parts.
STOP
Crush Hazard (Rolling Over)
When disconnecting the unit or leaving
the operator’s seat:
1. Stop the tractor or towing vehicle.
2. Shut off the engine and remove the ignition key.
3. Set the brakes.
4. Make sure wheel cylinder transport locks are
attached.
5. Relieve hydraulic fl uid pressure.
6. If parking the unit, make sure jack stand is
lowered and retaining pin is installed.
Injury Hazard
Do not permit children to play on or around the
stored unit.
WARNING
Impaired Operator Hazard
Do not attempt to operate this unit under
the infl uence of drugs or alcohol. Review
the safety instructions with all users annually.
Personal Protection Equipment
When working around or operating this unit, wear
appropriate personal protective equipment. This list
includes but is not limited to:
• A hard hat
• Protective shoes with slip resistant soles
• Protective goggles, glasses, or face shield
• Heavy gloves and protective clothing
Safe Distance
Keep all bystanders, especially children, away
from the unit while in operation.
SAFETY
INSTRUCTIONS
To prevent injury, use a tractor equipped with a
Roll Over Protective System (ROPS).
Visually Inspect
Visually inspect the unit for any loose bolts,
worn parts, or cracked welds, and make
necessary repairs before using the unit.
Towing Safety
For towing safety information, refer to the Towing section.
Operation Safety
For operating safety information, refer to the Operation
section.
Assembly Safety
For assembly safety information, refer to the separate
Assembly manual.
Maintenance Safety
For maintenance safety information, refer to the
Maintenance section.

888-627-8569 9 Quadra-Till from McFarlane Mfg.
Component Nomenclature
Component Locations
M200-0179
1 2
3 4
The Quadra-Till is comprised of four components: the
double disk gangs (1), the chisel shanks (2), the leveler
disks (3), and the four-bar harrow (4).
Component Description
Disk Gangs (1)
The disk gangs cut the residue, open the soil surface,
and begin the process of incorporating the residue into
the soil up to four inches deep. Adjusting the angle and
depth of the disk gangs is the fi rst step in sizing and
incorporating the residue.
The depth of the disk gang is adjusted hydraulically with a
cylinder. The disk gang depth ranges from 0 to 4 inches.
The depth of the disk is normally determined by the
amount of residue and the fi eld conditions. The deeper
the setting the more residue is incorporated into the soil.
The angle of the disk gang can be set in any one of three
settings. To incorporate the maximum amount of residue,
set the disk gang angle to the most aggressive setting of
#3. If residue and sizing are not an issue (like soybean
ground) then the disks should be set to the #1 setting and
the disks set as shallow as possible.
NOTICE
In high residue situations, maximum down pressure on
the disks is required to more completely cut the residue.
Make sure the C-spring stop does not constantly contact
the frame, as this will cause equipment damage.
Chisel Shanks (2)
The chisel shanks perform two tasks; they shatter the
soil and incorporate the residue. The chisel shanks
incorporate the residue evenly in the top of the profi le,
which is extremely important in vertical tillage. Too
much residue in the top two to three inches of the profi le
causes poor soil-to-seed contact, which results in uneven
germination.
The chisel shanks are also designed to shatter the soil
evenly across the profi le so any compaction layers are
broken up. The shank confi guration and spacing are set
to provide the best soil breakup and uniformity.
Depth adjustment for the chisel shanks uses a depth
stop which contacts a control valve located at the front
of the machine on the main frame. This valve controls
the position of the wheel lift cylinders. Since this moves
the whole machine up or down, the other components
need to be checked and possibly readjusted any time the
shank depth changes. The optimum working depth of the
chisel shanks is 6 to 12 inches.

Quadra-Till from McFarlane Mfg. 10 888-627-8569
Besides the depth setting, the operating characteristics of
the chisel shanks can be changed by the use of diff erent
points or shovels. The unit is shipped with three inch
twisted shovels as standard equipment. An optional four
inch twisted shovel is available which will move more dirt
and incorporate more residue. Also, an optional two inch
straight point is available which incorporates less residue
and requires less horsepower.
Spring Protection
Each chisel shank is equipped with a spring to protect it
from breaking in the event it hits something, such as a
rock. The spring tension is preset at the factory and no
adjustment is necessary.
Rear Leveler Disk Attachment (3)
The rear leveler disks are designed to level the ridges
left by the chisel shanks. They should be set low enough
to level the ridges, but not too deeply as they can create
furrows.
The rear leveler disks are adjusted with dual hydraulic
cylinders that move the rear section of the unit up or
down. Controls within the tractor cab allow the operator
to adjust the depth while moving across the fi eld.
Four-Bar Harrow (4)
The four-bar harrow is used to break up clods of soil and
disperse the residue evenly across the work area.
There are three attachment points for the pull chains on
the harrow section. Moving it up will cause the section
to lay more fl at (less aggressive) and moving it down
will cause the teeth to stand up more straight (more
aggressive).
In some situations that do not require the extra leveling
of the harrow section, such as heavy fall residue, the
sections can be removed.
QT-213F Disk Gang and Leveler Disk Toolbar
The model QT-213F is equipped with a fold-out disk gang
and leveler disk toolbar which decreases the transport
width to 16’4” (4.98 m).

888-627-8569 11 Quadra-Till from McFarlane Mfg.
QT-215F and QT-217F Disk Gang and Leveler
Disk Toolbar
The QT-215F and QT-217F models are equipped with
a fold-out disk gang and leveler disk toolbar which
decreases the transport width to 16’2” (4.93 m).
Disk Gang Gauge Wheels (215F and 217F)
The gauge wheels help to carry the weight of the chisel
frame wing. They are not designed to limit or set the
working depth of chisel.
Specifi cations
Hydraulic Requirements
This unit operates with hydraulic pressures of 2500 to
3000 psi (170 to 205 bars).
Number of Shanks
QT-207 — 7
QT-209 — 9
QT-211 — 11
QT-213 — 13
QT-213F — 13
QT-215F — 15
QT-217F — 17
Horsepower Range
QT-207 — 175 to 210
QT-209 — 225 to 270
QT-211 — 275 to 330
QT-213 — 325 to 390
QT-213F — 325 to 390
QT-215F — 375 to 450
QT-217F — 425 to 510
Tillage Depths
• Disk gang depth up to 4” (10.2 cm)
• Chisel shank depth 6 to 12” (15.2 to 30.5 cm)
• Rear Leveler disk depth is hydraulically adjustable to
match operating depth
Tongue Weight
Tongue weight of the unit is approximately 700 lbs. (318 kgs)
Overall Weight (GVWR)
QT-207 — 13,291 (6029 kg)
QT-209 — 14,497 (6576 kg)
QT-211 — 16,763 (7604 kg)
QT-213 — 18,309 (8305 kg)
QT-213F — 19,089 (8559 kg)
QT-215F — 24,840 (11,267 kg)
QT-217F — 26,500 (12,020 kg)
Transport Width
QT-207 — 12’8” (3.86 m)
QT-209 — 13’8” (4.17 m)
QT-211 — 17’3” (5.26 m)
QT-213 — 19’1” (5.82 m)
QT-213F — 16’4” (4.98 m)
QT-215F — 16’2” (4.93 m)
QT-217F — 16’2” (4.93 m)
Working Tillage Width (Cut Width)
QT-207 — 8’9” (2.67 m)
QT-209 — 11’3” (3.43 m)
QT-211 — 13’9” (4.19 m)
QT-213 — 16’3” (4.95 m)
QT-213F — 16’3” (4.95 m)
QT-215F — 18’9” (5.72 m)
QT-217F — 21’3” (6.48 m)
Towing Speed
Towing speeds should not exceed 20 MPH (32 KPH)
Field operating speeds should be 5 to 6-1/2 MPH (8 KPH
to 10-1/2 KPH)

Quadra-Till from McFarlane Mfg. 12 888-627-8569
Instructions for Display of Hazard and Infor-
mational Signs
• It is the responsibility of the customer to know the
lighting and marking requirements of the local
highway authorities and to install and maintain
the equipment to provide compliance with the
regulations. Add extra lights when transporting at
night or during periods of limited visibility.
• Keep safety signs clean and legible at all times.
Replace safety signs that are missing or have
become illegible.
• Do not paint over, remove, or deface any safety signs
or warning decals on your equipment. Observe all
safety signs and practice the instructions on them.
• Replacement parts that display a safety sign should
display the same sign.
• Make sure the hazard warning labels or other
information decals are legible and attached to the
unit before use.
• Safety signs are available from your Distributor,
Dealer Parts Department, or the factory.
M200-0130
5 Turns = 1”
Deeper
NOTICE DOWN
READ AND UNDERSTAND THE OPERATOR’S
MANUAL BEFORE USING.
TRANSPORT LOCKUPS MUST BE USED
DURING TRANSPORT.
DO NOT RUN THE DISK GANGS WITH THE
SPRING INDICATOR IN THE BLACK ZONE.
MAXIMUM FIELD TRAVEL SPEED IS 6.5 MPH.

888-627-8569 13 Quadra-Till from McFarlane Mfg.
NOTICE
READ AND UNDERSTAND THE OPERATOR’S
MANUAL BEFORE USING.
TRANSPORT LOCKUPS MUST BE USED
DURING TRANSPORT.
DO NOT RUN THE DISK GANGS WITH THE
SPRING INDICATOR IN THE BLACK ZONE.
MAXIMUM FIELD TRAVEL SPEED IS 6.5 MPH.
DC230b
Assembly
Refer to the Quadra-Till Assembly manual for complete
instructions.
Assembly
Manual
Version: MM-0903
Read and understand the manual.This manual provides information
and procedures to safely operate and maintain the Quadra-Till.
200 Series
SIZES, SHATTERS, MIXES, & LEVELS
MFG.CO.INC.
MADE IN THE USA

Quadra-Till from McFarlane Mfg. 14 888-627-8569
Towing
General Safety
SAFETY
INSTRUCTIONS
Towing the Quadra-Till requires care! Both the
unit and tow vehicle must be in good working
condition. Securely attach to towing unit. Use a
high strength, appropriately sized hitch pin with a
mechanical retainer and attach safety chain.
Make sure the hitch and coupling on the towing
vehicle are rated equal to, or greater than, the
unit’s “gross vehicle weight rating” (GVWR).
Refer to the specifi cation section.
Make sure the safety chain is securely fastened
to the tow vehicle.
Check the tires for tread wear, infl ation
pressure, and overall condition.
Inspect the hitch and coupling for wear or
damage. DO NOT tow the unit using a defective
hitch or coupling!
Make sure directional, brake, and running lights
are connected and working properly.
Make sure the lug nuts holding the wheels are
tight (torque to specifi cations) and that none
are missing.
When towing the unit on the highway, make
sure the “Slow Moving Vehicle” placard is
clearly visible.
Do not allow anyone to stand between the
tongue or hitch and the towing vehicle when
backing up to the equipment.
Make sure that the area is clear of children,
animals, and other obstacles before using.
Safety Chain
SAFETY
INSTRUCTIONS
• If the unit will be transported on a public highway, the
safety chain must be attached to the tow vehicle.
• Always follow state and local regulations
regarding a safety chain when towing farm
equipment on a public highway.
• Be sure to check with local law enforcement
agencies for any local regulations or
restrictions.
• Do not use any device other than the safety chain
that was supplied with the unit. Only a safety chain
(not an elastic or nylon/plastic tow strap) should
be used to retain the connection between the tow
vehicle and the unit in the event of separation of the
primary attaching system.
Bystanders
SAFETY
INSTRUCTIONS
• Beware of physical surroundings and
especially bystanders, particularly children,
before moving the unit! This is particularly
important with higher noise levels and quiet
cabs, as you may not hear people shouting.
• NO PASSENGERS ALLOWED - Do
not carry passengers anywhere on or
in the tractor, except as required for
operation.
• Do not allow anyone to ride on the unit while it
is moving.
Towing and Maximum Towing Speed
SAFETY
INSTRUCTIONS
• Operate the towing vehicle from the operator’s seat
only.
• Do not exceed a towing speed of more than 20 mph
(0.5 KPH) on a public roadway.
• Remember, tires supplied by the manufacturer
are designed to operate LESS THAN 20 mph.
Do not exceed or tire failure may occur.
Highway and Transport Operations
SAFETY
INSTRUCTIONS
• Make sure the wheel cylinder transport locks are
installed and the jack stand is in its storage position
before transporting the unit.

888-627-8569 15 Quadra-Till from McFarlane Mfg.
SAFETY
INSTRUCTIONS
• Never use independent braking with unit in tow as
loss of control and/or upset of unit may result.
• Always drive at a safe speed relative to local
conditions and ensure that your speed is low enough
for an emergency stop to be safe and secure. Keep
speed to a minimum.
• Reduce speed prior to turns to avoid the risk of
overturning.
• Avoid sudden uphill turns on steep slopes.
• Always keep the tractor or towing vehicle in gear to
provide engine braking when going downhill. Do not
coast.
• Use approved accessory lighting fl ags and necessary
warning devices to protect operators of other vehicles
on the highway during daylight and nighttime
transport. Various safety lights and devices are
available from your dealer.
• The use of fl ashing amber lights is acceptable in
most localities. However, some localities prohibit their
use. Local laws should be checked for all highway
lighting and marking requirements.
• When driving the tractor and equipment on the road
or highway, use fl ashing amber warning lights and a
slow moving vehicle (SMV) identifi cation emblem.
• Be a safe and courteous driver. Always yield to
oncoming traffi c in all situations, including narrow
bridges, intersections, etc. Plan your route to avoid
heavy traffi c.
• Be observant of bridge loading ratings. Do not cross
bridges rated lower than the gross weight at which
you are operating.
• Watch for obstructions overhead and to the side while
transporting.
• Always operate equipment in a position to provide
maximum visibility at all times. Make allowances for
increased length and weight of the equipment when
making turns, stopping, etc.
Pre-towing Checklist
1. Before towing, make sure the maintenance on the
tractor and the unit are current. This is very important
because towing puts additional stress on the tow
vehicle.
2. Check and correct the tire pressures on the tow
vehicle and the unit. Refer to the Tire and Lug Torque
specifi cation chart in the manual.
3. Make sure the hitch, coupler, and any other equipment
that connects the unit and the tow vehicle are properly
secured and adjusted. Always inspect the hitch and
tongue for cracks when hooking up.
WARNING
Substandard Parts Hazard
If towing the unit with a draw bar, use only an
OEM certifi ed, hardened drawbar pin with a
retainer clip. Do not use homemade pins, bolts, or
any other type of retaining device. Always install the
retainer clip, making sure the hitch and unit are
securely fastened to the tow vehicle.
Using a pin not intended for this type of towing, can
result in unexpected separation of the unit from the
tow vehicle resulting in equipment damage and
personal injury.
4. Verify the appropriate Category 3 (7 shank) or
Category 4 (9, 11, 13, 15, 17 shank) hitch is installed.
Model 207 Models 209 - 217F

Quadra-Till from McFarlane Mfg. 16 888-627-8569
WARNING
Unexpected Separation Hazard
If the safety chains do not have a current
certifi cation tag, do not use the unit until
properly certifi ed chains are installed. Substandard
safety chains could allow the unit to separate from
the tow vehicle resulting in equipment damage and
personal injury.
5. Attach the safety chain from the unit to the tow vehicle.
The safety chain should be long enough for tight
turns. Don’t allow the chain to drag on the pavement
because it will wear the chain links causing an unsafe
condition.
6. Make sure the electrical wiring harness for the running
and taillights is properly connected and not touching
the road, but loose enough to make turns without
disconnecting or damaging the wires.
7. Have an observer confi rm all running lights, brake
lights, turn signals, and hazard lights are working on
both the tow vehicle and the unit.
8. Verify the brakes on the tow vehicle are operating
correctly.
9. Make sure transport locks are securely fastened to the
cylinders and the hydraulic lock valve is in the closed
position.
10. Make sure the jack stand is raised and locked in the
storage position.
11. Check mirrors of the tow vehicle to make sure you
have good visibility.
12. Check routes and restrictions on bridges and tunnels.
Hook-Up to Tractor
Safety
SAFETY
INSTRUCTIONS
Make sure that anyone who will be operating
the unit or working on or around the unit reads
and understands all the operating,
maintenance, and safety information in the
operator’s manual and other related OEM
equipment manuals before using or towing the
unit.
Prior to Connecting Unit
Make sure the unit is resting on the ground or the
transport locks are securely installed over the wheel
cylinders before attaching the unit to the tractor.
SAFETY
INSTRUCTIONS
If the unit is not resting on the ground, make
sure wheel chocks are securely fi tted on both
sides of each wheel.

888-627-8569 17 Quadra-Till from McFarlane Mfg.
WARNING
Crush Hazard
The tongue weight of the unit is
approximately 700 lbs. (318 kgs.). Use
care when lifting or attaching the unit to the tractor.
Never place any part of your body under the tongue
or hitch assembly.
Hydraulic Pressure
This unit operates with hydraulic pressures of
2500 to 3000 psi (170 to 205 bars).
High-Pressure Fluids
1. Check or tighten all connections BEFORE
pressurizing system.
0
2. Release all pressure before removing hoses
and/or valves by:
a. Stopping engine.
b. Holding hydraulic control levers in fl oat or
neutral position.
3. DO NOT use your bare hand to check for
potential leaks. Always use a board or
cardboard when checking for a leak.
Escaping hydraulic fl uid under pressure, even a
pinhole size leak, can penetrate body tissue, causing
serious injury and possible death. If fl uid is injected
into your skin, it must be treated immediately by a
doctor familiar with this type of injury.
Tow Chain
A certifi ed tow chain is supplied with each unit. This
chain must be attached to the tractor during towing or
operation of the unit.
SAFETY
INSTRUCTIONS
Inspect the chain annually for wear or damage.
OEM
OEM
Do not replace the chain with anything other
than an OEM certifi ed replacement.
Connecting to the Tractor
1. Raise the jack stand and connect the tongue to the
tractor. The tongue weight of the unit is approximately
700 lbs. (318 kgs).
Note: If a drawbar pin is used, it should be an OEM
certifi ed pin and retainer clip. On Model QT-207,
category 3 pintle hitch use a 1-1/2” (38 mm) pin.
On Model QT-207, category 3 clevis hitch use
a 1-1/4” (32 mm) pin. On Models QT-209, QT-
211, QT-213, QT-213F, QT-215F, and QT-217F
category 4 pintle hitch use a 2” (51 mm) pin.
Model 207 Models 209 - 217F
2. Connect the hitch of the unit to the tractor. Attach the
tow chain to the tractor’s draw bar cage.

Quadra-Till from McFarlane Mfg. 18 888-627-8569
Note: When connected, make sure the retaining plate
securely locks the chain link in place.
3. Remove the jack stand in place it in its storage
position inside the frame, as shown.
4. Remove the six hydraulic hoses from their storage
position.
5. Connect the six hydraulic hoses to the tractor.
Note: The most commonly used function of the unit is
the “main lift” cylinders, which raises and lowers
the wheels. Connect the hydraulic hoses for this
function into the port (control lever) used most
commonly.

888-627-8569 19 Quadra-Till from McFarlane Mfg.
6. Disconnect the electrical connection for the rear lights
from the storage socket.
a. Rotate the plug.
b. Push the plug upward and slightly rotate it again to
release it from the socket.
c. Pull the plug downward.
d. Connect the plug into the tractor’s electrical socket.
7. Make sure all the hydraulic cylinders are functioning
properly.
8. Make sure the amber and red indicator lights are
working properly.
9. Move the unit to the desired location and position it
for operation following the towing recommendation
provided in this manual and/or any other local, State,
or Federal regulations that may apply.

Quadra-Till from McFarlane Mfg. 20 888-627-8569
Operation
Safety
WARNING
To prevent serious injury or death, follow these
safety instructions
Entanglement Hazard
Keep hands and clothing clear of moving parts.
Crush Hazard (Rolling Over)
Do not clean, lubricate, or make adjustments
while the unit is moving.
STOP
Crush Hazard (Rolling Over)
When making adjustments to the
unit or leaving the operator’s seat:
1. Stop the tractor.
2. Shut off the engine and remove the ignition key.
3. Set the brakes.
Overturn Hazard
Pick the levelest possible route when
transporting across fi elds. Avoid the edges of
ditches or gullies and steep hillsides.
Safe Distance
Keep all bystanders, pets, and livestock clear of
the work area, particularly when raising or
lowering the unit.
SAFETY
INSTRUCTIONS
Periodically clear the unit of brush, twigs, or
other materials to prevent buildup of dry,
combustible materials.
NOTICE
DO NOT turn while the unit is in the ground.
DO NOT operate the unit in frozen ground.
Initial Setup
The McFarlane Quadra-Till is a tool that is designed
to handle a wide variety of fi eld conditions. It has
many adjustments that can be made to change the
performance of each component on the unit as well as its
overall performance. Achieving the best results over the
widest range of circumstances can be accomplished by
making adjustments to match the fi eld conditions.
Note: It is important to make one adjustment at a time in
order to see the results of each change. If several
adjustments are made at the same time, the
operation of the machine can change dramatically,
creating confusion and frustration.
1. If necessary, remove the transport locks from both
wheel cylinders. Store the transport locks in their
storage positions on the frame, as shown.