Medeli DD620 User manual

1Check the include items
Setup Guide
CYMBAL PADS BOX
Cymbal Pad for Hi-Hat Cymbal Pad for Crash(with Choke)
DRUM PADS BOX DRUM MODULE BOX
ACCESSORIES BOX
KICK PEDAL BOX
STAND AND CYMBAL HOLDER BOX
HI-HAT PEDAL BOX
WARNING:
Drum key can be pinched when adjusting clamps with drum key. Operate carefully.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.
Cymbal Pad for Ride
(with Chock)
(Dual Zone)
Pad Mount X 4 Drumsticks
Drum Key
Hi-Hat Holder
AC Adaptor
Owner’s Manual Setup GuideConnection Cable X 9
Screw X 3
Cymbal Holder x 3
Pillar (R1) Pillar (M1)
Pillar (L1)
Center Pipe (1)
Right Cross P ipe
Center Pipe (2)
Left Cross Pipe
Cymbal Rod Clamp
AFI
Foot Pedal
Beater
0
5
25
75
95
100
aw_DD620_Setup Manual_G01_150923_with kick peda
2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:47:56

2Set Up the Stand
Wing N ut 1
Wing N ut 2
78
7.Attach the pad mounts to the mount h olders on
the Center Pipe (1), Right Cross Pipe, and firmly
tighten the respective wing nuts 1.
8.Insert the two cymbal holders into the holders on
the Center Pipe (1) Clamp, attach the hi-hat holder
to mount holders on the Cymbal Rod Clamp, and
firmly tighten the respective wing nuts .
Note:
Loose n o r tighten the wing nuts on the mount
holder as shown partial enlargement.
Move the moun t holder s as needed, and firmly
tighten the respective wing nuts 2.
Note:
Loosen or tighten the wing nuts on the mount
holder as shown partial enlargement.
Right C ross P ipe
Cymbal R od C lamp
Center P ipe (1)
Wing N ut
5
6
4
Left C ross P ipe
Pillar (L1)
3
2
1
1.Attach the Center Pipe (2) to the clamp on the Pillar (L1) & (R1)
2.Attach the Left Cross Pipe to the clamp on the Pillar (M1)
3.Attach the Left Cross Pipe to the clamp on the Pillar (L1)
4.Attach the Right Cross Pipe to the clamp on the Pillar (R1) & (M1)
5.Attach the Cymbal Rod clamp on the Pillar (L1)
6.Attach the Center Pipe (1) to the clamp on the Pillar (L1) & (R1)
Note:
Loosen or tighten the screws on the clamp with drum key as shown partial enlargement.
A djust the height of the Right Cross Pipe and Center Pipe (1) with Wing Nuts as needed.
Pillar (R1)
Center Pipe (2)
Pillar (M1)
Wing N ut 1
Wing N ut 2
Wing N ut
0
5
25
75
95
100
aw_DD620_Setup Manual_G01_150923_with kick peda
2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:47:57

3Attach the Parts
Attach the Pads
1.Loosen the wing nuts on the drum pads.
2.Attach the drum pads to the pad mounts,
and firmly tighten the wing nuts on the
drum pads.
Wing Nut
Wing Nut 1
Tom 1 Tom 2
Snare Tom3
Wing Nut 1
Wing Nut 2
Attach the Cymbal Pads
Wing Nut 3
Felt Washer
Wing Nut 4
Cymbal Tilter
12
Attach the AFI
Insert the AFI position as shown.
1.Remove the wing nut and felt
washer from the cymbal tilter.
2.Place the cymbal pad, felt
washer, wing nut 3 assembly as
shown, and tighten the wing nut
3 to obtain an appropriate
amount of sway.
3.Adjust the cymbal pad position
with the wing nut 4.
Note:
Put the cymbal on the cymbal
adapter and locate the tap of
the adapter in the slot of the
cymbal bottom.
Hi-Hat
Crash
Ride
AFI
Attach the Drum Module
1.Push the cable into the mount holder slot on as shown.
2.Connect cable to the DB25 Jack on the back of drum module.
3.Attach the module to the mount holder on the , and
firmly tighten with the screws.
Center Pipe (1)
Center Pipe (1)
Note:
Adjust the drum module position by moving the mount holders as
needed, and firmly tighten the relevant wing nut.
3
12
AFI
0
5
25
75
95
100
aw_DD620_Setup Manual_G01_150923_with kick peda
2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:47:59

DD620_G01
Connection Procedure
1.Place the kick on the floor in the center of the rack as shown.
2.Place the hi-hat pedal on the floor on your left side.
3.Connect the pads to the drum module with the marked cables.
Are you ready? Let's enjoy playing it.
Make connections as shown in the illustration.
AFI AFI
Drum M odule
Tom 1 Tom2
Snare Tom3
Ride
Crash
Hi-Hat
HI-HAT C ontrol Kick P ad
Tom3
Snare
Tom2
Tom1
Ride
Crash
Drum
Module
Hi-Hat
Hi-Hat
Pedal
Kick
Pad
AFI AFI
Tom3
4Connect the Pads to the Drum Module
Folding Drum Rack
5Folding Drum Rack
Drum rack through five steps can be completed folding.
1.Adjust the snare position as shown in figure 1.
2.Loosen 4 wing nut as shown in figure 1, push pillar (M) in the direction
o f arrow to folde as shown in figure 2.
3.Push down S nare/TOM3 in the direction of arrow down to as shown in figure 3.
4.Turn back HI-HAT Cymbal in the arrow direction as shown in figure 3、4.
5.Push down T OM1/TOM2 in the direction of arrow down to as shown in
figure 5,Drum rack be completed folding.
345
2
Snare Tom3
Tom1 Tom2
Crash Ride
HI-HAT
Drum Module
AFI AFI
Wing N ut 1
Wing N ut 2
Wing N ut 3
Wing N ut 4
1.Loosen t he wing Nut 1 ~ 4 ,Pillar (M)
in the direction of arrow to
appropriate location
2.Clamp turn to position as shown in
figure 2 , Complete the drum rack
Unfolding D rum R ack
Wing N ut 1
Wing Nut 3
Wing Nut 4
Wing Nut 2
1
0
5
25
75
95
100
aw_DD620_Setup Manual_G01_150923_with kick peda
2015󾾠󾾠9󾾠󾾠23󾾠󾾠 11:48:02