Medic Therapeutics NA-T1811B User manual

HEATED THROW
Manual
Please Read Manual Prior to Use

Control button
Indictor light
SET UP PROCEDURES
When setting up your heated product, be sure to follow these steps in order:
1. Locate cord connector on the product near the care instructions label.
2. Do not plug into the wall outlet until you have connected the controller cord to the product.
3
To connect the cable to the connector, align the connector and cable arrows and push gently until it locks.
CAUTION: The cable must be fully plugged in. A loose connection could cause a fire hazard.
4. Plug the power cord into a 110-120 wall outlet.
5. Make sure all cords are tangle free and not trapped or pinched in any way, including but not limited to
between mattress and box spring, sofa cushions, against wall, chairs, or other furniture.
6. Do not wrap the controller in the throw while in use.
7. Do not use with generator power.
8. To disconnect the controller, first unplug the cord from the outlet, then pinch sides of the connector
and pull apart.
CONTROLLER FEATURES
AUTO SHUT OFF FEATURE Each controller will automatically shut
off 4 hours after the controller is turned on. This is designed to
provide added safety and conserve energy. To reactivate the heating
feature simply press the power button. To restart after a power
outage simply press the power button.
To use:
1. Push the control button to turn on. The controller will default to
the lowest setting. Continue to press the button to adjust heat
setting up. A light will illuminate the selected heat setting.
2. To turn the control off, press the center button until no light is
seen on the controller. Caution: Always turn off the heated throw
and disconnect the power cord from the outlet when not in use.
3. Use for more than 30 minutes for better heat sensation.
ELECTRICAL SPECIFICATIONS
TROUBLESHOOTING
Q: The indicator light on my controller is flashing. What should I do?
A: Turn the controller off. Unplug the controller from the wall outlet. Unplug the controller cord from the
product. Wait 30 seconds and reconnect, making sure the arrows are properly aligned. Now plug into
the 110-120 volt wall outlet. Push control button until the temperature is on high. If you still have
issues, contact QUALITY IMPORTS USA INC customer service.
Locate connector
Connector
Locate and align arrows Plug into wall outlet
Label
Model No Voltage Frequency Wattage
NA-T1811B 120 V AC 60 Hz 115 W

Q: The controller is lit but the product does not heat up.
A: Test the product by folding the textile over on itself and turning the setting to high. Ensure that the
indicator light is on. After approximately five minutes, carefully feel between the layers. Caution: Never
leave the product turned on and folded up for more than 5-7 minutes.
Q: I feel some warmth but not a lot. How warm should this product get?
A: This product will provide enough warmth to keep you quite comfortable even in a very cold room. This
product is not like a heating pad. In normal operation, it does not feel hot to the touch, however the
warmth is evident when in use.
Q: Why is my controller warm?
A: A small amount of heat is produced when transferring power from the wall to the product. This warmth
is completely normal and is nothing to be concerned about.
IMPORTANT INSTRUCTIONS
To operate this warming product properly and safely, there are some critical safety precautions you need to
follow. As with all electrical appliances, there is an inherent danger of overheating, fire or personal injury if
the product is not used correctly. Please carefully read what follows before using the warming product.
Never use this warming product with;
• Infants or very small children;
• People with disabilities;
• Anyone who is immobile or cannot operate the controls properly;
• Anyone who is insensitive to heat (e.g. a person with poor circulation);
• Anyone who cannot or will not understand these directions.
SAFETY ESSENTIALS
Setting up
• NEVER trap or pinch any of the electrical cords in any way. Make sure the cords are NEVER rested
between the mattress and box springs.
• The heated area should always lie flat to prevent overheating.
• If the plug does not fit into your outlet, contact a qualified electrician.
• Be sure that the power supply is used only on 120V, 60 HZ current supply.
• Make sure the cord from the controller to your heated product is connected and locked tightly.
• You may use this electric product with any sheets, mattress pads or other blankets but NEVER in
combination with any other electric blankets or electric mattress pads.
• The warming product should never be folded, balled up or bunched in any way when in use. May result in
overheating and/or permanent wrinkling of the fabric.
Care and Maintenance
• Do not use with generators, power converters, or inverters.
• NEVER use pins in and around the warming product.
• Cats, dogs and other pets should always be kept away from the product, as a sharp claw may result in
damage to the heating element.
• Keep the controls away from drafty areas that may become damp or wet, such as an open window.
• Always turn off the electric current when the warming product is not in use, either by turning off the
controller or unplugging from the wall outlet.
• Wrapping of the cord around the controls may damage the cord. Loop loosely when storing.
• NEVER iron your warming product.
• NEVER use dry cleaning fluid on this product. Cleaning solvents may damage the wiring insulation.
• Do not tuck in the wired area of this bedding
• Do not route electrical cords between the mattress and box spring.
• Do not allow the cords to be pinched.
• Keep the control away from drafty areas that may become damp or wet such as an open window. Do not
use pins -They may damage the electric wiring.
• Be sure that this bedding is used on an alternating-current supply circuit of the proper voltage.
• Turn off or unplug when not in use.
• Excessive heating may result from folding bedding, other than a mattress, when in actual use.
• If improper operation of this bedding is observed, discontinue its use immediately and consult the
manufacturer or the dealer regarding its repair.

• For throw blankets only: Do not use with rocking chairs, recliners, chairs with casters or wheels, or
other furniture subject to movement.
• Do not tuck the blanket or supply cord in a sofa or other furniture.
• All portions of the blanket or controller should be visible at all times.
• Wrapping of cord around the controller may damage the cord.
• Loop loosely when storing.
CARE INSTRUCTIONS
WASHING INSTRUCTIONS
NEVER DRY CLEAN OR USE BLEACH. BEFORE WASHING, DISCONNECT ALL CORDS.
MACHINE WASHING
NEVER submerge cords or control unit. Place textile portion without cords in the washing machine.
Machine wash warm on gentle or delicate cycle.
HANDWASHING
Washing your warming product by hand is the best way to make it last. To do this, disconnect all cord(s).
Wash your textile separately by hand in a tub of lukewarm (100°F) water using a small amount of mild
laundry soap or detergent. Soak for 5 minutes. Next, gently work the textile up and down for five
more minutes. NEVER rub or scrub. Rinse thoroughly in cool water until all traces of soap or detergent are
gone. Squeeze excess water out by hand, NEVER twist. Do not use a wringer.
DRYING INSTRUCTIONS
NEVER USE COMMERCIAL DRYERS ATTHE LAUNDROMAT THEY MAY BE EXTRA HOT AND COULD
DAMAGETHE WIRING. DO NOT IRON. DO NOT PLUG IN UNTIL COMPLETELY DRY.
MACHINE DRY
To machine dry, put your product into a dryer on low heat and allow to tumble until dry. Ensure that the
textile has enough room to tumble freely. If product draws in during washing, while still damp gently
stretch until it returns to its original size.
LINE DRY
You can line dry, simply by draping over two parallel clotheslines or a shower rod with the head and foot
ends down. Do not reconnect warming products until they are completely dry. Do not use clothes pins that
can pinch wires.
STORAGE
Store as you would any other bedding, folded in a dry place.
LIMITED LIFETIME WARRANTY
Your Medic Therapeutics Heated Throw is backed by a limited lifetime manufacturer’s warranty. Medic
Therapeutics will repair or replace your device at any time should it fail due to a defect in material or
workmanship, subject to the certain limitations.
This limited warranty does not cover any damage that results from unauthorized or improper use, service,
or repair. Further, it does not cover damage caused by accident, impact, negligence, or normal wear and
tear. Should you discover your Medic Therapeutics Heated Throw is not functioning properly, please send
your device to our repair center for evaluation. If your product cannot be repaired or serviced we will
reserve the right to change it for a similar or newer model.
Please note that a flat rate of $35.00 will be charged to cover a service evaluation fee and return shipping
of your device. All warranty claims must be accompanied by a copy of your proof of purchase from an
authorized retailer. Please send your device, proof of purchase, and a check or money order in the amount
of $35.00 made out to Medic Therapeutics to:
Medic Therapeutics Service Center
3069 Taft Street
Hollywood, FL 33009
Contact: warr[email protected]
Table of contents
Other Medic Therapeutics Accessories manuals
Popular Accessories manuals by other brands

Velleman
Velleman VMA314 user manual

QUAD
QUAD 7741 instruction manual

First Alert
First Alert MOTION SENSING M08-0222-000 user manual

Siko
Siko LE100/1 Translation of the original installation instructions

Big Daishowa
Big Daishowa BASE MASTER BM-50 Operation manual

Honeywell
Honeywell PEHA 940 RS Installation and operating instructions

elsner elektronik
elsner elektronik KNX AQS/TH-B-UP Technical specifications and installation instructions

PCB Piezotronics
PCB Piezotronics 117B66 Installation and operating manual

Eldes
Eldes EWM1 user guide

triOS
triOS eCHEM 90S220000 operating instructions

Siemens
Siemens Wireless Room Sensor Solution user guide

Denon
Denon DHT-T110 manual