Medion MD 81485 User manual

MD 81485 1
CONTENTS
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
What’s in the box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fit the installation frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Inserting the car radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Removing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Explanation for using the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Radio functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Playing Audio CDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Playing MP3 CDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
WMA files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
USB connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Card reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Disposal information . . . . . . . . . . . . . . . . . . . . . . . . . 23
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CarRadio MD 81485_AUS.fm Seite 1 Donnerstag, 17. August 2006 7:50 07

2
OVERVIEW
1. PWR: turn device on/off (the device can also be turned on with any other key
except OPEN)
2. VOL–/VOL+: Turn to control volume;
Audio setting:
SEL: Press repeatedly to call up the following audio settings: volume, bass,
treble, balance, fader; turn to adjust selected audio setting;
Volume default; time setting, sound effect:
Press and hold SEL:
VOL 17: Volume default; turn to adjust the volume default;
ADJ 00:00 ( TIME SETTING): turn clockwise to adjust the hour; turn
anticlockwise to adjust the minutes;
DSP NONE: turn to select the desired sound effect FLAT, CLASSIC, ROCK and
POP.
CD/MP3 mode:
in search mode, select track or character [see SCH key (9)].
3. Display
4. LOU: loudness/BND: band selector/ENTER: confirm selection.
5. LOC: select local or distance reception.
LOC ON: recommended setting in areas with strong signals;
LOC OFF: recommended setting in areas with weak signals.
6. MO/ST: Select mono or stereo reception in radio FM mode.
7. REL : Open control panel
8. A/PS and SCH
Radio mode:
– Press and hold A/PS for more than 1 second: the radio will search for six
stations and store them into the preset memory 16 (there are 18 FM stations
and 12 AM stations).
– Press A/PS for less than 1 second: the radio will scan the six preset stations
and stop for 5 seconds at each station.
CD/MP3/ MMC/SD/USB mode:
Press SCH once to enter into search mode; then turn the VOL knob to select
the desired track number; then press ENTER (19) for playback.
Only MP3 MODE:
Press SCH twice to enter into FILE EDIT mode (searching for names of titles) or
ROOT SEARCH (accessing the directories of the MP3 CD);
– FILE EDIT – example: searching for the name „Duo“:
Press SCH twice to enter the file edit mode; the current track number is
displayed; then rotate the VOL knob to select the character „D“; the display
shows „DXX“; press SEL (VOL knob) to confirm; rotate the VOL knob to select
„U“, press SEL; the display shows DUX; press SEL to confirm; rotate the VOL
knob to select „O“;
CarRadio MD 81485_AUS.fm Seite 2 Donnerstag, 17. August 2006 7:50 07

Overview
MD 81485 3
press ENTER (19) to confirm and press again to playback the title.
– ROOT SEARCH: Press SCH twice to enter the file edit mode; press SEL (VOL
knob) three times to enter the root search mode; the first directory will be
displayed; rotate the VOL knob or press the SKIP keys (10) repeatedly to
select the directory; press ENTER (19) for playback of the directory.
9. SKIP
In radio mode:
press slightly repeatedly to search for a specific frequency manually;
press and hold for more than two seconds to start an automatic
search; the search will stop at the first found channel;
In CD/SD/MMC mode:
press slightly to skip to the previous/next track;
press and hold to start a fast search.
10. SCAN: Automatic station search in radio mode.
Press SCAN to start the search. If the unit receives a radio signal, the display
will flash ten times to show the frequency; then it will continue to seek another
signal until you press SCAN again or you store the station into the preset
memory (press and hold M1-6 for more than one second).
11 . MUTE: Press to mute the sound output.
12.  17. M1 - M6, in radio mode:
Preset memory keys. To store the current station, press and hold one of the
M keys for more than one second).
Press briefly to recall the stored station.
12. (M1): Play/Pause function in CD/SD/MMC/USB mode.
13. RPT (M2): Repeat current track in CD/SD/MMC/USB mode.
14. INT (M3): Intro function in CD/SD/MMC/USB mode; press to play each track
for 10 seconds . Press again to stop the intro function.
15. RDM (M4): Random playback in CD/SD/MMC/USB mode. Press to playback
the track in random order.
16. –10 (M5): Press in CD/SD/MMC/USB mode to search the –10 track.
17. +10 (M5): Press in CD/SD/MMC/USB mode to search the +10 track.
18. DISP
In radio mode: press repeatedly to display frequency or clock time;
In any other mode:press repeatedly to display playback time, frequency or
clock time.
19. BAND/ENTER
In radio mode: Press BAND repeatedly to select the radio frequency: FM1 >
FM2 > FM3 > AM1 > AM2
Other function modes (e. g. track search): Press ENTER to confirm selection.
20. MODE: Press repeatedly to select the mode: Radio > CD (and MP3) > USB >
SD/MMC.
21. Flip cover to protect card slots (see 2527)
CarRadio MD 81485_AUS.fm Seite 3 Donnerstag, 17. August 2006 7:50 07

Overview
4
CD player/card reader/USB (behind control panel and
flap cover)
22. EJECT: eject CD
23. RESET opening: reset to factory settings
24. CD compartment
25. SD/MMC slot (card reader); plug SD/MMC card in for playback. The operation
is identical with MP3 discs.
26. USB plug
27. Red LED as antitheft function
CarRadio MD 81485_AUS.fm Seite 4 Donnerstag, 17. August 2006 7:50 07

MD 81485 5
SAFETY INSTRUCTIONS
Keep electrical equipment out of reach of children
The appliance is not intended for use by young children or infirm persons without
supervision.
Young children should be supervised to ensure that they do not play with the
appliance.
Road safety
Road safety should be your top priority. Use your car radio only in
suitable traffic conditions. Please ensure that you are familiar with
the radio before setting off.
You should always be able to hear police, fire and other emergency
service sirens immediately while you are in your vehicle. For this
reason, please play your radio at an appropriate volume while
driving.
Never undertake your own repairs
Under no circumstances should you attempt to open and/or repair
this unit on your own. Refer all servicing to MEDION Help Desk on
1300 884 987.
CD player
The CD player is a Class 1 laser product. The device has a safety
system that prevents dangerous laser rays escaping from the
device during normal use. In order to avoid injury to the eyes,
never interfere with or damage the unit's security system.
About these instructions
Please read these instructions carefully before using the device.
Note the warnings on the device and in the operating instructions
Store the operating instructions in the car. If you sell
or give the car
radio away, please ensure that you also pass on these instructions.
CarRadio MD 81485_AUS.fm Seite 5 Donnerstag, 17. August 2006 7:50 07

Safety instructions
6
Using the CD player
Never place any objects other than CDs into the disc compartment. Otherwise
you might damage the precisely engineered pullin mechanism.
Moisture and high humidity may cause the CD player to malfunction. If this
occurs, switch on the vehicle's heater to evaporate the moisture before use.
Do not expose the CD player to extremely high or low temperatures.
Installation
Before installation, disconnect the battery first. There is a risk of short-
circuit and electric shock!
Please use the car radio's ISO block for installation. Never disconnect the ISO
block. Disconnecting the cables voids the guarantee!
Avoid installing the set in the following circumstances:
high temperatures (e.g. caused by strong sunlight or direct heated air)
dust, dirt
and vibrations.
This can damage the device.
Cleaning the device
Use a soft, dry cloth to clean the device. Avoid the use of chemical solutions and
cleaning products, because these may damage the unit's surface and/or the
labels on it.
IMPORTANT!
We recommend that you have this product installed by a qualified
installer. The supplier will not be liable for any damages caused to this
product or to other devices in the car as a result of incorrect installation.
CarRadio MD 81485_AUS.fm Seite 6 Donnerstag, 17. August 2006 7:50 07

MD 81485 7
WHAT’SIN THE BOX?
The following are included in the delivery pack:
INSTALLATION
Before installation, disconnect the car battery! There is a risk of short-
circuit and electric shock!
The car radio is designed to be fitted in a
standard ISO installation slot. The
dimensions of this slot are 182 mm x 53 mm.
It has two ISO plugs and an antenna plug.
If your vehicle has no ISO slot, please consult a specialist garage, dealer,
or the specialist department of a large store.
Installation instructions
• Place the set in the ISO slot provided for it.
• If changes have to be made to the vehicle, consult your vehicle dealer/
specialist garage.
• If the unit is installed at an angle of over 30° off
the horizontal, this may reduce its optimal
output capacity.
• Avoid installing the unit near strong heat (e.g.
direct sunlight or heated air), dust, dirt or strong
vibrations. This can damage the set.
Car radio Control panel
Mounting frame (clipped on) Control panel case
Frame (clipped on) ISO connector with blank wires
2 fitting wrenches Operating instructions and warranty card
Maximal installation angle
CarRadio MD 81485_AUS.fm Seite 7 Donnerstag, 17. August 2006 7:50 07

Installation
8
Fit the installation frame
• Before installation, always use a phillips
head screwdriver to remove the two
transport safety screws in the top part of the
radio casing (marked with red flags)!
• The car radio is delivered with the
installation frame fitted over it. Firstly
remove the mounting frame from the car
radio casing. To do this, push down the two
clips on the sides of the car radio (1) and
push the mounting frame off the radio from
behind (2).
• Insert the mounting frame in the ISO
installation slot.
• In order to fix the mounting frame in the
installation slot, use a screwdriver to bend
out as many clips as possible. Choose the
clips which fit tightly against the installation
slot casing.
Next, check that the frame fits tightly. The frame must be tightly fitted, to
prevent it from coming loose if the driver brakes sharply.
CarRadio MD 81485_AUS.fm Seite 8 Donnerstag, 17. August 2006 7:50 07

Installation
MD 81485 9
Cable connections
A general view of the back of the car radio:
Connect up the cables
• Pull out the connections in your car's ISO slot far enough for you to join them
to the ones from the car radio.
Please use the car radio's ISO block for installation. Never disconnect the ISO
block  If your car's ISO plugs do not fit the car radio's ISO sockets, you can buy
suitable adapters in specialist garages, from dealers and the specialist
departments of large stores.
Secure, proper electrical connections are provided by your car' s two ISO
plugs (for the loudspeakers and the power connections). In case you still
wish to lay the cables yourself, we explain in detail the uses of the cables
at the end of this chapter.
[A] Connect the vehicle's antenna plug to the radio's antenna socket.
[B] If you use an external amplifier, you can connect it to the red/white RCA
audio sockets. Please also refer to your instructions for the amplifier.
[C] Connect the vehicle's two ISO plugs (one ISO plug for ISO Block A and one
for ISOBlock B) to the car radio's ISO block.
CarRadio MD 81485_AUS.fm Seite 9 Donnerstag, 17. August 2006 7:50 07

Installation
10
Test station memory
In some vehicle models the standard arrangement for the
standard plus and permanent plus cables has been switched in
the factory (see“Arrangement of the ISO block” on page 13). This
can lead to the station memory not working.
Before you finally install the car radio, try the following to find out if you have
saved the stations.
• Reconnect the car battery.
• Turn on the ignition.
• Switch the radio on.
• Go through the automatic station saving process, holding down the A/PS/SCH
[8]key for approx. two seconds (see also“Automatic saving” on page 16).
• Switch the ignition off.
• Switch on the ignition again and find out if the stations have been saved (press
the station buttons 1bis 6 [12-17]).
• If the stations have been saved, you can install the radio.
• If the stations are no longer in the memory, you should use an adapter,
obtainable from the specialist store, or have the cable adapted in a specialist
garage. If this is the case, refer to Chapter “Explanation for using the cables”
on page 12.
Inserting the car radio
• Push the car radio carefully into the slot until it
clicks into place.
While pushing the radio in, be careful how you fit
the cables; they should not be kinked, crushed or
stretched.
CarRadio MD 81485_AUS.fm Seite 10 Donnerstag, 17. August 2006 7:50 07

Installation
MD 81485 11
Control panel
Inserting the control panel
• First place the right side of the
control unit with its lower right
corner on the pin in the lower
right corner of the frame.
• Then press the lower left side
until it clicks into place.
• Flip the control panel upwards.
Check that the control panel is
properly in place and secure. If the
control panel is not fitted properly,
error messages appear in the
display and/or several keys will not function properly.
Removing the control unit
• Press the REL button [7].
• Push the control unit slightly to
the right and pull down first the
lefthand side and then the right.
If the control unit has not been inserted in the frame, the antitheft LED will
flash on the unit.
For protection, always keep the control unit in its case.
RESET
In order to start the radio working, press the RESET [23]
button with the point of a ballpoint pen or something else
sharp.
Removing the unit
• Remove the control unit.
• Pull out the frame.
• Insert the right and left keys in the slots
on the sides of the set. The flaps will be
bent back and you can remove the set.
CarRadio MD 81485_AUS.fm Seite 11 Donnerstag, 17. August 2006 7:50 07

Installation
12
Explanation for using the cables
The explanatory notes for using the cables are intended for when the
cables have to be fitted individually. Consult a specialist garage and pass
on the information contained in this chapter.
To connect the radio to your vehicle's ISO plugs, you do not need these
explanatory notes.
Overview of the cables:
Notes on fitting cables.
Memory back-up (yellow)
The yellow memory backup cable needs to be connected to the permanent plus.
Otherwise the station memory will not work (see “Arrangement of the ISO block” on
page 13).
Antenna relay cable (blue)
The blue cable is available for a relaycontrolled antenna. The relay extends the
antenna automatically when the radio is switched on. When it is switched off, the
antenna is retracted.
This relay cable can also be used to control an external amplifier. Please refer to
the amplifier's operating instructions for the correct connections.
Never connect the blue cable to the engine cable; this could damage the
radio!
Colour Function
Red 12 V Plus
Black Ground
Yellow Power Antenna
Pink Memory 12 V +
Green Front LSpeaker (+)
Green/Black Front LSpeaker ()
White RearRSpeaker (+)
White/Black RearRSpeaker ()
Grey FrontRSpeaker (+)
Grey/Black FrontRSpeaker ()
Blue RearLSpeaker (+)
Blue/Black RearLSpeaker ()
CarRadio MD 81485_AUS.fm Seite 12 Donnerstag, 17. August 2006 7:50 07

Installation
MD 81485 13
Arrangement of the ISO block
Problems due to switched cables
In some vehicle models, the standard arrangement of cables [4] and [7] in the
ISO block A (see above, "ARRANGEMENT OF THE ISO BLOCK") are switched at
the factory.
If this is the case in your vehicle, certain functions may be impaired: stations may
not be stored properly, for example.
To solve this, the red cable (switched plus) and the yellow cable (permanent
plus) will need to be reversed in the ISO block.
BLOCK B – speakers BLOCK A – electricity supply
1 right rear + 1
2 right rear  2
3rightfront+ 3
4 right front  4 Permanent plus (permanent
12V supply from main
electrical system)
5 left front + 5 Car antenna (also for
external amplifiers, etc.)
6 left front  6
7 left rear + 7 Switched plus (switched 12V
voltage, via ignition)
8 left rear  8 Earth
CarRadio MD 81485_AUS.fm Seite 13 Donnerstag, 17. August 2006 7:50 07

14
OPERATION
Basic operation
Switching on/off
Press the PWR button (1) to switch the radio on or off.
Volume
• Turn the volume control knob (2) to turn the volume up or down.
Always set the volume so that you can still clearly hear the sirens from
emergency vehicles!
Functions when pressing the volume knob
• Press SEL button to change the mode in the sequence of
VOLUME > BASS > TREBLE > BALANCE > FADER.
• Press once. When " VOL" is displayed, you can adjust the sound level by
rotating the VOL+/ VOL knob.
• Press twice. When "BAS" is displayed, you can adjust the bass effect by
rotating the VOL+/ VOL knob.
• Press three times. When "TRE" is displayed, you can adjust the treble effect
by rotating the VOL+/ VOL knob.
• Press four times. When "BAL" is displayed, you can rotate VOL+ to decrease
the sound level of left speakers or rotate VOL to decrease the sound level of
right speakers.
• Press five times. When"FAD" is displayed, you can rotate VOL+ to decrease
the sound level of rear speakers or rotate VOL to decrease the sound level of
front speakers.
Functions when holding the volume knob
• Press and hold SEL button, you can rotate VOL+/VOL to adjust the setting of
VOL 17; ADJ 00:00; DSP NONE.
• Press once. IN VOL 17 is indicated: The volume output default setting can be
adjusted. When power is on, the output level can be returned to default setting
if the output level is over the default setting. Conversely, it will maintain the
level if the output level is below the default setting.
• Press twice. ADJ 00:00 is indicated: TIMING SETTING. For time setting, hold
the SEL button until the clock display is blinking. You can rotate the volume
CarRadio MD 81485_AUS.fm Seite 14 Donnerstag, 17. August 2006 7:50 07

Operation
MD 81485 15
clockwise to adjust "HOUR", and then rotate the volume anticlockwise to
adjust "MINUTE".
• Press three times.  DSP NONE is indicated: To select the desired sound
effect among FLAT, CLASSIC, ROCK and POP. Choose the setting DSP
NONE to turn the sound effect off.
Loudness
• Press the LOUD button (4) to strengthen the bass.
Display
By pressing the DISP button (18) you can change the screen display as follows:
• Radio Mode: press this button to display the radio frequency or clock time.
• CD/MP3 Mode: Press this button to display playback time, frequency or clock
time.
MODE
• Press the MOD button (20) to switch between radio reception, CD/MP3
operation, USB connection and card reader.
RESET
• To reset the car radio to the factory settings, press the
RESET button (23) with a pointed object, such as a pen.
• Press RESET (23)
 before first use, after connecting the cable,
 if not all function keys are working,
 when an error message appears in the display.
CarRadio MD 81485_AUS.fm Seite 15 Donnerstag, 17. August 2006 7:50 07

Operation
16
Radio functions
Selecting the radio frequency
• Press the BAND/ENTER button (19) to switch between FM (FM1, FM2 & FM3)
and AM (AM1 & AM2). You can store up to 6 stations in each band.
Searching for a station
• Briefly press the TUN/TRK 8(17) or TUN/TRK 9 (18) scan buttons. The set will
search for the next station.
• Switch to manual station search by pressing one of the two buttons for two
seconds. The display shows MANUAL.
Save station
• After the search function has found a station, press one of the 1-6 (1015)
station buttons for around three seconds. A beep will sound to indicate that
the station has been stored.
The radio will switch back into automatic search mode after a few seconds.
Selecting stations
• Select the radio frequency by pressing BAND/ENTER (19).
• You can open one of the saved stations by pressing one of the station buttons
1-6 (1015).
Automatic saving
• Press the A/PS/SCH button (8) until you hear a beep. The display shows
SEARCH. The scan stops for five seconds each time a station is found. The
number flashing on the display is the number of the button which saves the
station. The search continues automatically on weak stations.
Running through saved stations
• You can call up the saved stations for the current transmission areas.
• Select the radio frequency by pressing BAND/ENTER (19).
• Press the A/PS/SCH button (8) briefly. All stations are now briefly selected.
• When you hear the station you require press the A/PS/SCH button (8) briefly.
CarRadio MD 81485_AUS.fm Seite 16 Donnerstag, 17. August 2006 7:50 07

Operation
MD 81485 17
Playing Audio CDs
Inserting and removing CDs
• Fold down the control panel (Button 1).
• Insert the CD into the slot with the labelled side upwards (25).
• Then close the control panel again. The CD will start to play. The display shows
[S-CDP].
• To remove the CD open the control panel again. Press the EJECT (22) button.
The CD will be ejected. The car radio will change back to radio mode.
Do not drive with a CD sticking out of the player. Remove the CD right away.
Skipping tracks
• By pressing the SKIP (9) buttons, you can select the previous or next track on
the CD. The track number is shown on the display.
Pausing the CD
• You can pause the CD by pressing the button (12). Pressing the button
again will restart CD playback.
Fast forward/rewind
• Hold down the SKIP (9) buttons for longer, to start fast forward or fast rewind.
Preview tracks
• Press the INT button (14). All tracks are played for around 10 seconds each.
Pressing the button again will change the playback mode back to normal.
ESP  Electric Shock Protection
The device is equipped with an antishock function. This function
compensates for vibrations, for instance, from a bumpy road, and ensures
playback without interruption, even if the player is moving around.. When the
player is switched on, the memory is automatically filled with data:
 with audio CDs it is for 12 seconds;
 with MP3 CDs it is for 120 seconds;
Further information on playing CDs
Moisture and high humidity may cause the CD player to malfunction. If this
occurs, switch on the vehicle's heater to evaporate the moisture before use.
Do not expose the CD player to extremely high or low temperatures.
CarRadio MD 81485_AUS.fm Seite 17 Donnerstag, 17. August 2006 7:50 07

Operation
18
Repeat a track
• Press the RPT button (13) to repeat the current track. Pressing the button
again will change the playback mode back to normal.
Random track playback
• Press the RDM button (15). The player will "shuffle" through the tracks,
playing them in random order. Pressing the button again will change the
playback mode back to normal.
Playing MP3 CDs
The basic functions are the same as those for audio CDs (refer to previous
chapter). However, for MP3 CDs you can select the track and artist directly. The
use of this function and other MP3specific functions will depend to some
degree on the MP3 CD itself. Please bear this in mind when producing this type
of CD (refer to next chapter).
All common encodings can be played back.
Producing MP3 CDs; ID3 tags
As with data CDs, MP3 CDROMs may contain individual tracks or folders.
When producing an MP3 CD, please ensure that you do not save tracks on
the same level as directories but only inside the directories. Mixing tracks
and directories at the same level may produce playback problems.
When producing an MP3 CD you can also save socalled "ID3 tags" (we
recommend using an ID3 tag editor for entries). This is a block of information
stored on an MP3 CD lying "behind" the actual music information of the MP3.
This may include such items as the artist, track, album name, year of publication
and a short comment. The car radio can read this information block and show it
on the display.
CarRadio MD 81485_AUS.fm Seite 18 Donnerstag, 17. August 2006 7:50 07

Operation
MD 81485 19
Searching for tracks (numbers)
Search for track numbers
• When A/PS/SCH button (8) is pressed at MP3 play mode, FILE EDIT and
ROOT SEARCH become possible:
File Edit Example
How to edit for the file name "DUO":
• Press A/PS/SCH (8) key twice to go into the file edit mode. The current
playback track number is displayed, then rotate the VOL button once to select
"D".
• At this time, the display shows "DXX"
• Press the SEL button again, then rotate the VOL button to select "U" At this
time, the display shows "DUX"
• Press the SEL button again, then rotate the VOL button to select "O" At this
time, the display shows "DUO".
• Press BAND/ENTER once to confirm, then press BAND/ENTER again to play
the selected file.
ROOT SEARCH EXAMPLE
If the structure of MP3 disc is as follows:
Total directories: 4, Total songs: 7, Directories with MP3 songs: 3 (A,C,D)
A. We can regard directory as MP3 folder.
B. In sequence, it is located as: A C D A ...
C. To listen a MP3 song
• Press SEL button three times to go into the root search mode, " A" directory
is displayed.
• Rotate the VOL button or press / button to select "D" directory.
• Press ENTER button to playback first songs in "D" directory "e.mp3" file.
WMA files
This player can also play WMA files. The operation functions in the same way as
for MP3 files.
CarRadio MD 81485_AUS.fm Seite 19 Donnerstag, 17. August 2006 7:50 07

20
USB CONNECTION
Playback
You can connect an MP3 player or another data medium to the USB connection
on the front of the unit.
Your car radio can process USB data media up to 1GB.
The directory structure may contain up to 1024 folders, 4096 files and a
directory depth of 8 levels.
• Remove the protective cover from the USB connection (7).
• Connect your USB device to the socket. The radio will search for MP3 or WMA
files on the storage medium and USB will appear on the display.
• Search and playback functions for files on an external storage medium work
in the same way as for MP3 CDs.
• If the device is in another mode (CD or card reader), you can select the card
reader with the MODE (20) button.
• Replace the protective cover on the USB connection when no USB device is
attached to prevent dirt from getting into the system.
CarRadio MD 81485_AUS.fm Seite 20 Donnerstag, 17. August 2006 7:50 07