MegaLite 7000-Drama LED W User manual

USER MANUAL
Table of Contents
Safety Information……………………………………………………………………………………3
Specifications……………………………………………………………………………….………..4
Main Power Connection………………………………………………………………………….....5
DMX-512 Connection……………………………………………………………...……………......5
DMX Profile.............................................................................................................................6
Main Control Menu..................................................................................................................7
Rigging the Fixture…………………………………………………………..……………………….8
Cleaning & Maintenance..........................................................................................................8
Parts List..................................................................................................................................8

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured away from unit movement.
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
5. Unit must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

Technical Information
4
Part Numbers
Fixture
7000-Drama LED W
Mechanical Specifications
Fixture Packaged for Shipping
Size: 23”L x 13.75”W x 19”H
Weight: 11 lbs
Size: 24.5”X 10.5” X 10.5
Weight: 13 lbs
DMX Connectors: 3-pin XLR connectors in/out
Power Connections: Nema 5-15 cable mounted connection
Thermal: Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Display:Digital
Fastening System: Mounting Yoke
Electrical Specifications
LED Type: 1 Wafer LED
LED Watts: 120
Color Temp: 6200K
LED Lifetime: 60,000 to 100,000 hours
Lens Options:19°,26°,36° and 50°
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Watts: 295
Amps: 2.46
Protocol: DMX 512
DMX Channels: 3 Mode of operation
Mode A 1 Channel On/Off
Mode P 1 Channel Dimmer
Mode F 2 Channel Dimmer/Strobe
Operating mode: Stand alone 15 step Dimmer setting via display
Control & Programming
23”
13.75” Open 10.5”
19” Open
17.5” Closed

5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
2
1
3
1
3
2
DMX-512 Connection
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a
shielded twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller
with the fixture or the fixture with another.
DMX—Input DMX—Output
1. Shield
2. Signal (-)
3. Signal (+)
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a
120 Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it
in to the last fixture on the signal run. Pre-manufactured terminator plugs are availa-
ble for purchase from your Mega-Lite dealer (HOS-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
LN
110V—Connection LL 220V—Connection