MegaLite NOVA-LITE Q200 User manual

USER MANUAL
Table of Contents
Safety Information…………………………………………………………..…………………….3
Specifications……………………………………………………………………………………...4
Main Power Connection………………………………………………………………………….5
DMX-512 Connection…………………………………………………………………...………..5
Main Control Menu..............................................................................................................6
DMX Profile.........................................................................................................................8
Rigging the Fixture………………………………………………………………………………..9
Cleaning & Maintenance....................................................................................................10
Parts List............................................................................................................................10

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 113º.
Protection Against Electrical Shock
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. This unit is IP 22 rated (do not expose unit to rain or moisture )
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

4
4450-Nova-Lite Q200
Mechanical Specifications
Fixture Packaging
Size: 10.25” x 8” x 16.87”
Weight: 10.25lb
Size: 20” x 12” x 11”
Weight: 13lb
Electrical Specifications
Protocol: DMX 512
DMX Modes: Mode 3 Channels R,G,B
Mode 4 Channels R,G,B,W
Mode 5 Channels Dimmer, R,G,B,W
Mode 7 Channels Dimmer, R,G,B,W, Strobe, Macro
Mode 8 Channel Dimmer, R,G,B,W, Strobe, Macro, Dim Speed
Control Options: Display preset setting
Control & Programming
DMX Connectors: Neutrik 3 & 5 pin
Power connection: Neutrik Power Con to Nema 5-15 (cable mounted)
Thermal: Maximum ambient temperature 105°
Maximum surface temperature 113°
Fastening System: Dual Yoke
Display: Digital
Lens Angles: 55º reflector,
30º and 15º degree lens (included)
60º Beam 80º Field angle diffusion lens (accessory)
LED Quantity: 1 COB LED’s Red, Green, Blue and White
LED Watts: 200W
LED Lifetime: 40 to 80 thousand hours average
Refresh Rate: 6000 Hz
Power Input Voltage: 110V-240 50/60 Hz
Ballast: Electronic auto switching
Power Consumption: Watts: 160
Amps: 1.35
Part Numbers
10.25”
Technical Information
16.87”
7.36”
8”
12.75”

5
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 240V automatically
3. This unit must be earthed. (electronically grounded)
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz
The fixture is equipped with 3 and 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only
use a shielded twisted pair cable designed for RS-485 and 3 or 5 pin XLR plugs and connectors in order to connect the
controller with the fixture or the fixture with another.
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-
sistor between the (-) and the (+) signal into a 3 or 5 pin XLR plug and plug it in to the last fixture
on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (P-DMX-T).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
DMX-512 Connection
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
LN
Main Power Connection
DMX—Input DMX—Output
1. Shield
2. Signal (-)
3. Signal (+)
4. N/A
5. N/A
2
3
15
3
4
2
11
2
3
1
2
3
4
5

Display Menu
6
DMX Address
Press Set Up to select the DMX start channel use the up/down keys, Press Set Up to confirm the setting
DMX Mode
This function allows you to select the mode in witch you want to control the fixture. Press Set Up use the up/down keys
to select desired DMX mode settings. Press Set Up to confirm the settings.
3 CH
4 CH
5 CH
Red, Green, Blue
Red, Green, Blue, White
Dimmer, Red, Green, Blue, White
Color Dimmer
This function allows you to dim up or down the LED’s . Press Set Up use the up/down keys to select desired color to ad-
just settings.
Mode Set Up Up Down
CONTROL BOARD
MegaLite
NovaQ200
DMX
Address
Channel Mode
7 CH
8 CH
Dimmer, Red, Green, Blue, White, Strobe, Macro
Dimmer, Red, Green, Blue, White, Strobe, Macro, Dim Speed
Dimmer
Red
Dimmer
Green
Dimmer
Blue
Dimmer
White
Dimmer
Use the up/down keys to select desired color to adjust. Press Set Up to confirm.
(note; Last set color will return when in Color Dimmer mode.)

7
Fade
This function allows you to select a preprogrammed fade sequences speed. Press Set Up use the up/down keys to se-
lect desired fade program speed (15 options). Press Set Up to confirm the settings.
Strobe
Dimming Speed
Press Set Up to select the desired dimming speed when used with a DMX controller. Use the up/down keys to select
from 1= Linear 2=Square 3=Inv Squa 4=S Type . Press Set Up to select Fast or Smooth option. Press Set Up to confirm
the setting.
This function allows you to select a preprogrammed strobe sequences. Press Set Up use the up/down keys to select
desired strobe program (15 options). Press Enter to set the desired sped use the up/down keys (15 options). Press Set
Up to confirm the settings. (note; Dimmer of selected color must be dimmed prior in Dimmer option)
Strobe Mode
Fade Mode
Dimming Curve
Settings
Settings
LCD
Back Light
DMX
Fail
DMX
Synchronous
Factory
Reset
Use the up/down keys to select desired wait time before auto turn off of the display or
on for always on display. Press Set Up to confirm.
Use the up/down keys to select the function of the light if DMX signal is removed. Off
will turn the dimmer off. Hold will hold the last DMX command. Press Set Up to Con-
firm
Use the up/down keys to select to return the fixture to original factory settings
When using a low frequency refresh controller select no (factory setting is yes)

8
DMX Profile
Nova-Lite Q200 3CH Mode
DMX Chanel Function Description Value
1LED Color Red LED intensity 0-255
2LED Color Green LED Intensity 0-255
3LED Color Blue LED Intensity 0-255
Nova-Lite Q200 4CH Mode
DMX Chanel Function Description Value
1LED Color Red LED intensity 0-255
2LED Color Green LED Intensity 0-255
3LED Color Blue LED Intensity 0-255
4LED Color White LED Intensity 0-255
Nova-Lite Q200 5CH Mode
DMX Chanel Function Description Value
1Dimmer Dimmer 0-255
1LED Color Red LED intensity 0-255
2LED Color Green LED Intensity 0-255
3LED Color Blue LED Intensity 0-255
4LED Color White LED Intensity 0-255
Nova-Lite Q200 7CH Mode
DMX Chanel Function Description Value
1Dimmer Dimmer Off to Full 0-255
2LED Color Red LED intensity 0-255
3LED Color Green LED Intensity 0-255
4LED Color Blue LED Intensity 0-255
5LED Color White LED Intensity 0-255
No Function 0-1
6Strobe Strobe (slow to fast) 2-196
Random Strobe (slow to fast) 197-255
No Function 0-1
Color fade All (slow to fast) 2-19
Color Snap All (slow to fast) 20-39
Random Color Snap (slow to fast) 40-59
Red fade (slow to fast) 60-79
Green fade (slow to fast) 80-99
7Macro Blue fade (slow to fast) 100-119
White fade (slow to fast) 120-139
Macro Effect 1 140-159
Macro Effect 2 160-179
Macro Effect 3 180-199
Macro Effect 4 200-219
Macro Effect 5 220-229
Macro Effect 6 230-249
Macro Effect 7 250-255

Nova-Lite Q200 8CH Mode
DMX Chanel Function Description Value
1Dimmer Dimmer Off to Full 0-255
2LED Color Red LED intensity 0-255
3LED Color Green LED Intensity 0-255
4LED Color Blue LED Intensity 0-255
5LED Color White LED Intensity 0-255
No Function 0-1
6Strobe Strobe (slow to fast) 2-196
Random Strobe (slow to fast) 197-255
No Function 0-1
Color fade All (slow to fast) 2-19
Color Snap All (slow to fast) 20-39
Random Color Snap (slow to fast) 40-59
Red fade (slow to fast) 60-79
Green fade (slow to fast) 80-99
7Macro Blue fade (slow to fast) 100-119
White fade (slow to fast) 120-139
Macro Effect 1 140-159
Macro Effect 2 160-179
Macro Effect 3 180-199
Macro Effect 4 200-219
Macro Effect 5 220-229
Macro Effect 6 230-249
Macro Effect 7 250-255
No Function 0-15
Curve 1 Linear Smooth 16-45
Curve 2 Square Law Smooth 46-75
8Dimming Curve 3 Inv Square Law Smooth 76-105
Curve Curve 4 S-Type Smooth 106-135
Curve 1 Linear Fast 136-165
Curve 2 Square Law Fast 166-195
Curve 3 Inv Square Law Fast 196-225
Curve 4 S-Type Fast 226-255
9
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
Rigging the fixture

10
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installa-
tions and electronics checked by an expert every year.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are
to be carried out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating. (Line Fuse is located inside the fixture)
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by author-
ized dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
4450-DRI LED Driver card
4450-PS Power Supply
4450-DIS Display
4450-KN Knob Set
4450-LED Replacement LED
4450-FP Frontal Plastic
4450-KNS Small Knob Set
Cleaning and Maintenance
4450-DIF60 60 Degree Diffusion Lens
4450-BD Barn Door
4450-CT Ceiling Tile Holders (set)
4450-DIF15 15 Degree Lens
4450-DIF30 30Degree Lens
4450-BD Barn Door
4450-HPM Hanging Point Metric (10mm)
Accessories
4450-DT Decorative Trim (Custom Color)
4450-HPS Hanging Point Standard ( 1/2 inch)
Pendant Mount: When using pendant and treaded mount
consider the following
1) Remove the yoke as it will no longer be used.
2) Using a standard 1/2 bolt you can hang the fixture by thread-
ing directly into the top. ( a metric 10mm version is also
available part #4450-HPM)
3) Using a steel cable you can hang the fixture by running a
steel cable throw the side hole
4) It is very important that you secure the fixture with a second-
ary safety .

Mega-Lite
18668 Highway 16N
Helotes, TX 78023
Ph 210-684-2600 Fax [phone]
www.mega-lite.com / [e-mail]
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LEDs are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice and Return Authorization Number given by MSI.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.