MegaLite Tiltbot TRIO User manual

Table of Contents
Safety Information 3
Specifications 4
Main Power Connection 5
DMX-512 Connection 5
Size and Weight 6
Main Control Menu 7
DMX Profile 9
Parts List 8
Rigging the Fixture 12
Cleaning & Maintenance 13
USER MANUAL

3
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 140º.
Protection Against Electrical Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. This fixture must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
Ingress Protection
IP 65
Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 140º.
Protection Against Electrical Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 6.
3. This unit must be earthed. (electronically grounded)
4. This fixture must not be left on for long periods of time.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
The IP rating is commonly expressed as IP (Ingress Protection) is followed by 2 numbers (i.e. 65)
where the numbers define the fixture rating. The first number indicates the size of a particle that can
enter the fixture.. The second number indicates the extent of protection against water entering the
fixture. An IP65 rating in this fixture indicates that dust particles can not enter the fixture. And there is
protection against powerful water spray from entering the fixture from any direction.

Technical Information
4
Part Numbers
Fixture Road Case
1310-Tiltbot Trio CAS-1310-4 4 Unit Road Case
Mechanical Specifications
DMX Connectors: Panel Mounted IP67 5-pin XLR connectors in/out
Power Connections: Panel Mounted Seetronic IP Rated Power in/out connection (Nema 5-15 to Seetronic power Female cable included)
Thermal: Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Display:Digital
Fastening System: 2 Quick Release Clamp Mount
Lens Angle: N/A°
Ip Rating: IP64
Electrical Specifications
LED Type: 572 RGB 1W and 144 White 8W
CRI: 90 on White
LED Lifetime: 50,000 to 80,000 hours (Average)
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Watts: 713W
Amps: 6.22A
PF: .99
Protocol: DMX 512
RDM: Yes
DMX Channels: 6 Mode of Operation
Mode 3 Ch: Tilt, Fine Tilt, Strobe
Mode 12 Ch: Tilt, Fine Tilt, Dimmer, RGB Intensity, Red, Green, Blue, Duration RGB, Strobe RGB, White, Duration White, Strobe
White
Mode 14 Ch: Tilt , Fine Tilt, Dimmer, Red, Green, Blue, Macro, Macro Speed, RGB Strobe, White, Macro, Macro Speed, White
Strobe, White Dim
Mode 23 Ch: Tilt, Fine Tilt, White, W Duration, W Strobe, Macro, Control, RGB intensity, RGB Duration, RGB Strobe, Macro, Red,
Green, Blue, FX Fade, Color FX, Color Select, White FX, White Select, Color Back, Intensity, Red back, Green Back, Blue Back
Mode 50 Ch: Tilt, Fine Tilt, RGB X 12, White X 12
Mode 62 Ch: Tilt , Fine Tilt, Dimmer, Red, Green, Blue, Macro, Macro Speed, RGB Strobe, White, Macro, Macro Speed, White
Strobe, White Dim, RGB X 12, White X 12
Operating Mode: Stand alone 255 step dimmer setting via display
Auto preprogram via display
Control & Programming

5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 240V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
5. Power Link 2 units at 110V and 4 units at 220V
The occupation of the connection-cable is as follows:
DMX-512 Connection
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-
sistor between the (-) and the (+) signal into a 5 pin XLR plug and plug it in to the last fixture on the
signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-Lite
dealer (P-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
LN
110V—Connection
LL
220V—Connection
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
5
3
4
2
11
2
3
4
5
4. N/A
5. N/A
The fixture is equipped with 5 pin XLR cable mounted sockets for DMX input and output. The sockets are wired in paral-
lel. Only use a shielded twisted pair cable designed for RS-485 and 5 pin XLR plugs and connectors in order to connect
the controller with the fixture or the fixture with another.

Size and Weight
6
Size 22.12" X 13.12" X 5.5"
Weight 23lb
Packaged 27.36" X 9" X 17.25" 25lb
22.12”
13.12”
7”
7.75”
5.5”
5”
4.86”

Main Control Menu
The control board on the fixture is your interface to access and control
all the functions on the unit. Its digital display gives you a code view of
the options and functions. The following will explain each function and
its options.
7
ESC DOWN UP ENTER
CONTROL BOARD
Mega Lite
Tiltbot Trio
DMX Address
Press Enter to select the DMX start channel. Use the up/down keys (001 to 512) , Press
Enter to confirm the setting. Press ESC to return to Main Menu.
(Notes: Display must be on Main Menu for fixture to operate on DMX Mode)
Address
001
DMX On
Press Enter to select the DMX Channel mode of operation. Use the up/down
keys to select Channel mode from. Press Enter to confirm the setting. Press ESC
to return to Main Menu
Channel Mode
Main Menu
>Channel Mode
Led Dimmer
Strobe Mode
LED Dimmer
Main Menu
Channel Mode
>Led Dimmer
Strobe Mode
For LED Dimmer control press Enter. Select from 255 steps. Of the 50 ch. Press ESC to
return to Main Menu.
Auto Mode
Main Menu
>Auto Mode
Auto Speed
Fan Test
Press Enter. Select from 6 modes Press ESC to return to Main Menu.
(Note: If you want to have fixture remain on Auto Test do not press ESC and just power off
and on fixture to return to last setting)
Strobe Mode
This function allows you to select a preprogrammed strobe sequences. Press Enter use
the up/down keys to select desired strobe program (15 options). Press Enter to set the
desired sped use the up/down keys (15 options). Press Enter to confirm the settings.
(note; Dimmer of selected intensity must be dimmed prior in Dimmer option)
Main Menu
Channel Mode
Led Dimmer
>Strobe Mode
14 CH Tilt , Fine Tilt, Dimmer, Red, Green, Blue, Macro, Macro Speed, RGB Strobe, White, Macro, Macro Speed, White Strobe, White
Dim
12 CH Tilt, Fine Tilt, Dimmer, RGB Intensity, Red, Green, Blue, Duration RGB, Strobe RGB, White, Duration White, Strobe White
3 CH Tilt, Fine Tilt, Strobe
23 CH Tilt, Fine Tilt, White, W Duration, W Strobe, Macro, Control, RGB intensity, RGB Duration, RGB Strobe, Macro, Red, Green,
Blue, FX Fade, Color FX, Color Select, White FX, White Select, Color Back Intensity, Red back, Green Back, Blue Back
50 CH Tilt, Fine Tilt, RGB X 12, White X 12
62 CH Tilt , Fine Tilt, Dimmer, Red, Green, Blue, Macro, Macro Speed, RGB Strobe, White, Macro, Macro Speed, White Strobe, White
Dim, RGB X 12, White X 12

8
Auto Speed
Main Menu
Auto Mode
>Auto Speed
Fan Test
Press Enter. Select from 6 modes Press ESC to return to Main Menu.
(Note: If you want to have fixture remain on Auto Test do not press ESC and just power off
and on fixture to return to last setting)
Setting
Setting Control Options
Main Menu
Temperature
>Setting
Config Menu
>LCD Back Light
DMX Fail
RDM
To turn off LCD Screen after 2 minutes of no use select Disable. To enable screen
to remain on when in use select Enable.
Config Menu
LCD Back Light
>DMX Fail
RDM
To hold the last DMX command is case of DMX Signal loss select Enable. To have
the fixture DMX Setting at 0 if DMX signal is loss use Disable option.
Config Menu
Fan Speed
>Dimmer Setting
Factory Rese
Select Dimmer Setting to be used for dimming type when used in Ch13 / 62mode.
Applies only to White LED’s
Linear
Square Law
Config Menu
Fan Speed
Dimmer Setting
>Factory Reset
Restore fixture to original factory display settings
Temperature
This fixture is equipped with internal temperature sensors. Once head reaches a tempera-
ture of 96°the IP rated fan will engage
Main Menu
Auto Mode
Auto Speed
>Fan Test
Config Menu
LCD Back Light
DMX Fail
>RDM
RDM Status You can Enable or Disable the RDM feature
RDM UID 6342774B9875
RDM ID 0001
Config Menu
>Fan Speed
Dimmer Setting
Factory Reset
Fan Speed Option include
Standard=
Low=
High=

9
DMX Profile
Tiltbot Trio 3 Ch Mode
DMX Channel Function Description Value Init
1Tilt Tilt 0-255 127
2Tilt Fine Tilt Fine 0-255 127
3Strobe No Function 0-10 0
Strobe (slow to fast) 11-255
Tiltbot Trio 12 Ch Mode
DMX Channel Function Description Value Init
1Tilt Tilt 0-255 127
2Tilt Fine Tilt Fine 0-255 127
3Dimmer Dimmer (off to full) 0-255 255
4RGB Intensity RGB Intensity 0-255 255
5LED Color Red LED Intensity 0-255 255
6LED Color Green LED Intensity 0-255 255
7LED Color Blue LED Intensity 0-255 255
8Duration Duration RGB 0-255 255
9Strobe Strobe RGB 0-255 255
10 LED Color White LED Intensity 0-255 255
11 Duration Duration White 0-255 255
12 Strobe Strobe White 0-255 255

10
Tiltbot Trio 14 Ch Mode
DMX Channel Function Description Value Init
1Tilt Tilt 0-255 127
2Tilt Fine Tilt Fine 0-255 127
3Dimmer Dimmer (off to full) 0-255 255
4LED Color Red LED Intensity 0-255 255
5LED Color Green LED Intensity 0-255 255
6LED Color Blue LED Intensity 0-255 255
No Function 0-1
Fade 1,2,3,4,5,6,12,11,10,9,8,7 2-17
Fade 12,11,10,9,8,7,1,2,3,4,5,6 18-35
Snap 1,2,3,4,5,6,12,11,10,9,8,7 36-53
7RGB Snap 12,11,10,9,8,7,1,2,3,4,5,6 54-71 0
Macro Fade 1+2+3+4+5+6 then 7+8+9+10+11+12 72-89
(Select Color) Snap 1+2+3+4+5+6 then 7+8+9+10+11+12 90-107
Bounce 1+7,2+8,3+9,4+10,5+11,6+12 108-125
Bounce 6+12, 5+11,4+10,3+9,2+8,1+7 126-143
Fade 1+7,2+8,3+9,4+10,5+11,6+12 144-161
Fade 3+4+9+10, 2+8+5+11,1+7+6+12 162-179
Snap 1+12,2+11,3+10,4+9,5+8,6+7 180-197
Bounce 1+12,2+11,3+10,4+9,5+8,6+7 198-215
Snap 3+10, 4+9, 2+11, 5+8,1+12, 6+7 216-233
Fade Random 234-244
Snap Random 245-255
8Macro Speed Macro Speed 0-255 0
No Function 0-1
Strobe (slow to fast) 2-127
9RGB Strobe Pulse (slow to fast) 128-170 0
Strobe Random Strobe All (slow to fast) 171-213
Random 1-12 Strobe (slow to fast) 214-255
10 LED Color White LED Intensity 0-255 255
No Function 0-1
Fade 1,2,3,4,5,6,78,9,10,11,12 2-17
Fade 12,11,10,9,8,7,65,4,3,2,1 18-35
Snap 1,2,3,4,5,6,7,8,9,10,11,12 36-53
11 White Snap 12,11,10,9,8,7,65,4,3,2,1 54-71 0
Macro Fade 1+2+3+4+5+6 then 7+8+9+10+11+12 72-89
(Select Intensity) Snap 1+2+3+4+5+6 then 7+8+9+10+11+12 90-107
Bounce 1,2,3,4,5,6,7,8,9,10,11,12 108-125
Bounce 12,11,10,9,8,7,6,5,4,3,2,1 126-143
Bounce 6+7,5+8,4+9,3+10,2+11,1+12 144-161
Fade 6+7,5+8,4+9,3+10,2+11,1+12 162-179
Snap 6+7,5+8,4+9,3+10,2+11,1+12 180-197
Bounce 1+12,2+11,3+10,4+9,5+8,6+7 198-215
Snap 1+2+3+4+9+10+11+12 then 5+6+7+8 216-233
Fade Random 234-244
Snap Random 245-255
12 Macro Speed Macro Speed 0-255 0
No Function 0-1
Strobe (slow to fast) 2-127
13 White Strobe Pulse (slow to fast) 128-170 0
Strobe Random Strobe All (slow to fast) 171-213
Random 1-12 Strobe (slow to fast) 214-255
No Function 0-50
14 White Dim Curve Linear 51-100 0
Square Law 101-150
Slow Burn Out (slow to fast) 151-255

Tiltbot Trio 23 Ch Mode
DMX Channel Function Description Value Init
1Tilt Tilt 0-255 127
2Tilt Fine Tilt Fine 0-255 127
3White Dimmer Dimmer (off to full) 0-255 0
4White Duration Duration 0-255 255
5White Strobe Strobe (slow to fast) 0-255 255
No Function 0-36
Ramp Up 37-40
Ramp Up Random 41-44
Ramp Down 45-48
Ramp Down Random 49-52
Ramp Up Down 53-56
Ramp Up Down Random 57-60
Random White Beam 61-64
Random Single Pixel White 65-68
Lighting 69-72
Spikes (flash over light) 73-76
White Beam (left to right) 77-80
White Beam (left to right random) 81-84
White Beam (right to left) 85-88
White Beam (right to left random) 89-92
White Beam (left to right bounce) 93-96
White Beam (left to right random) 97-100
White Beam (left to right bounce) 101-104
White Beam (right to left bounce random) 105-108
6Macro Zig (6 steps) 109-112 0
Zig (6 steps random) 113-116
Zig (6 steps out to center pixel) 117-120
Zig (6steps out to center pixel random) 121-124
Zigzag (10 steps) 125-128
Zigzag (10 steps random) 129-132
Reserved 133-179
Double Flash 180-183
Double Flash (random) 184-187
Double Flash (beam color) 188-191
Double Flash (beam color random) 192-195
Double Flash (color beam) 196-199
Double Flash (color beam random) 200-203
Triple Flash 204-207
Triple Flash (random) 208-211
Triple Flash (bcb) 212-215
Triple Flash (bcb random) 216-219
Triple Flash (cbc) 220-223
Triple Flash (cbc random) 224-227
Quad Flash 228-231
Quad Flash (random) 232-235
Quad Flash (bcb) 236-239
Quad Flash (bcb random) 240-243
Quad Flash (cbc) 244-247
Quad Flash (cbc random) 248-251
Reserved 252-255
11

No Function 0-49
FX / Pattern Color Priority On 50-54
FX / Pattern Color Priority Off 55-59
No Function 60-69
Normal Tilt Control 70-74
Invert Tilt Control 75-79
Normal Pixel Orientation 80-84
7Control Invert Pixel Orientation 85-89 0
No Function 90-209
Duration Percentage Mode On 210-214
Duration Percentage Mode Off 215-219
No Function 220-229
FX / Plate Color Priority On 230-234
FX / Plate Color Priority Off 235-239
No Function 240-247
Reset 248-255
8Color Intensity Color Intensity (off to full) 0-255 0
9Color Duration 7-650 Ms 0-255 255
10 Color Strobe Strobe (slow to fast) 0-255 255
No Function 0-36
Ramp Up 37-40
Ramp Up (random) 41-44
Ramp Down 45-48
Ramp Down (random) 49-52
Ramp Up / Down 53-56
Ramp Up / Down (random) 57-60
Random White Beam 61-64
Single White (random) 65-68
11 Color Macro Lighting 69-72 0
Spikes (flash over low) 73-76
Reserved 77-179
Double Flash 180-191
Double Flash (random) 192-203
Triple Flash 204-215
Triple Flash (random) 216-227
Quad Flash 228-239
Quad Flash (random) 240-251
No Function 252-255
12 LED Color Red Intensity 0-255 255
13 LED Color Green Intensity 0-255 255
14 LED Color Blue Intensity 0-255 255
15 FX Cross Fade FX Cross Fade Duration 0-255 0
16 Color FX Movement (slow to fast) 0-255 0
17 Color Select Color Pattern Select 0-255 0
18 White FX Movement (slow to fast) 0-255 0
19 White Select White Pattern Select 0-255 0
20 Color Back Background Color Intensity 0-255 0
21 Background Color Red Background Intensity 0-255 255
22 Background Color Green Background Intensity 0-255 255
23 Background Color Blue Background Intensity 0-255 255
12

Tiltbot Trio 50 Ch Mode
DMX Channel Function Description Value Init
1Tilt Tilt 0-255 127
2Tilt Fine Tilt Fine 0-255 127
3LED Color 1 Red LED Intensity 0-255 255
4LED Color 1 Green LED Intensity 0-255 255
5LED Color 1 Blue LED Intensity 0-255 255
6LED Color 2 Red LED Intensity 0-255 255
7LED Color 2 Green LED Intensity 0-255 255
8LED Color 2 Blue LED Intensity 0-255 255
9LED Color 3 Red LED Intensity 0-255 255
10 LED Color 3 Green LED Intensity 0-255 255
11 LED Color 3 Blue LED Intensity 0-255 255
12 LED Color 4 Red LED Intensity 0-255 255
13 LED Color 4 Green LED Intensity 0-255 255
14 LED Color 4 Blue LED Intensity 0-255 255
15 LED Color 5 Red LED Intensity 0-255 255
16 LED Color 5 Green LED Intensity 0-255 255
17 LED Color 5 Blue LED Intensity 0-255 255
18 LED Color 6 Red LED Intensity 0-255 255
19 LED Color 6 Green LED Intensity 0-255 255
20 LED Color 6 Blue LED Intensity 0-255 255
21 LED Color 7 Red LED Intensity 0-255 255
22 LED Color 7 Green LED Intensity 0-255 255
23 LED Color 7 Blue LED Intensity 0-255 255
24 LED Color 8 Red LED Intensity 0-255 255
25 LED Color 8 Green LED Intensity 0-255 255
26 LED Color 8 Blue LED Intensity 0-255 255
27 LED Color 9 Red LED Intensity 0-255 255
28 LED Color 9 Green LED Intensity 0-255 255
29 LED Color 9 Blue LED Intensity 0-255 255
30 LED Color 10 Red LED Intensity 0-255 255
31 LED Color 10 Green LED Intensity 0-255 255
32 LED Color 10 Blue LED Intensity 0-255 255
33 LED Color 11 Red LED Intensity 0-255 255
34 LED Color 11 Green LED Intensity 0-255 255
35 LED Color 11 Blue LED Intensity 0-255 255
36 LED Color 12 Red LED Intensity 0-255 255
37 LED Color 12 Green LED Intensity 0-255 255
38 LED Color 12 Blue LED Intensity 0-255 255
39 LED Color 1 White LED Intensity 0-255 255
40 LED Color 2 White LED Intensity 0-255 255
41 LED Color 3 White LED Intensity 0-255 255
42 LED Color 4 White LED Intensity 0-255 255
43 LED Color 5 White LED Intensity 0-255 255
44 LED Color 6 White LED Intensity 0-255 255
45 LED Color 7 White LED Intensity 0-255 255
46 LED Color 8 White LED Intensity 0-255 255
47 LED Color 9 White LED Intensity 0-255 255
48 LED Color 10 White LED Intensity 0-255 255
49 LED Color 11 White LED Intensity 0-255 255
50 LED Color 12 White LED Intensity 0-255 255
13

Tiltbot Trio 62 Ch Mode
DMX Channel Function Description Value Init
1Tilt Tilt 0-255 127
2Tilt Fine Tilt Fine 0-255 127
3Dimmer Dimmer (off to full) 0-255 255
4LED Color Red LED Intensity 0-255 255
5LED Color Green LED Intensity 0-255 255
6LED Color Blue LED Intensity 0-255 255
No Function 0-1
Fade 1,2,3,4,5,6,12,11,10,9,8,7 2-17
Fade 12,11,10,9,8,7,1,2,3,4,5,6 18-35
Snap 1,2,3,4,5,6,12,11,10,9,8,7 36-53
7RGB Snap 12,11,10,9,8,7,1,2,3,4,5,6 54-71 0
Macro Fade 1+2+3+4+5+6 then 7+8+9+10+11+12 72-89
(Select Color) Snap 1+2+3+4+5+6 then 7+8+9+10+11+12 90-107
Bounce 1+7,2+8,3+9,4+10,5+11,6+12 108-125
Bounce 6+12, 5+11,4+10,3+9,2+8,1+7 126-143
Fade 1+7,2+8,3+9,4+10,5+11,6+12 144-161
Fade 3+4+9+10, 2+8+5+11,1+7+6+12 162-179
Snap 1+12,2+11,3+10,4+9,5+8,6+7 180-197
Bounce 1+12,2+11,3+10,4+9,5+8,6+7 198-215
Snap 3+10, 4+9, 2+11, 5+8,1+12, 6+7 216-233
Fade Random 234-244
Snap Random 245-255
8Macro Speed Macro Speed 0-255 0
No Function 0-1
Strobe (slow to fast) 2-127
9RGB Strobe Pulse (slow to fast) 128-170 0
Strobe Random Strobe All (slow to fast) 171-213
Random 1-12 Strobe (slow to fast) 214-255
10 LED Color White LED Intensity 0-255 255
No Function 0-1
Fade 1,2,3,4,5,6,78,9,10,11,12 2-17
Fade 12,11,10,9,8,7,65,4,3,2,1 18-35
Snap 1,2,3,4,5,6,7,8,9,10,11,12 36-53
11 White Snap 12,11,10,9,8,7,65,4,3,2,1 54-71 0
Macro Fade 1+2+3+4+5+6 then 7+8+9+10+11+12 72-89
(Select Intensity) Snap 1+2+3+4+5+6 then 7+8+9+10+11+12 90-107
Bounce 1,2,3,4,5,6,7,8,9,10,11,12 108-125
Bounce 12,11,10,9,8,7,6,5,4,3,2,1 126-143
Bounce 6+7,5+8,4+9,3+10,2+11,1+12 144-161
Fade 6+7,5+8,4+9,3+10,2+11,1+12 162-179
Snap 6+7,5+8,4+9,3+10,2+11,1+12 180-197
Bounce 1+12,2+11,3+10,4+9,5+8,6+7 198-215
Snap 1+2+3+4+9+10+11+12 then 5+6+7+8 216-233
Fade Random 234-244
Snap Random 245-255
12 Macro Speed Macro Speed 0-255 0
No Function 0-1
Strobe (slow to fast) 2-127
13 White Strobe Pulse (slow to fast) 128-170 0
Strobe Random Strobe All (slow to fast) 171-213
Random 1-12 Strobe (slow to fast) 214-255
No Function 0-50
14 White Dim Curve Linear 51-100 0
Square Law 101-150
Slow Burn Out (slow to fast) 151-255
14

15 LED Color 1 Red LED Intensity 0-255 0
16 LED Color 1 Green LED Intensity 0-255 0
17 LED Color 1 Blue LED Intensity 0-255 0
18 LED Color 2 Red LED Intensity 0-255 0
19 LED Color 2 Green LED Intensity 0-255 0
20 LED Color 2 Blue LED Intensity 0-255 0
21 LED Color 3 Red LED Intensity 0-255 0
22 LED Color 3 Green LED Intensity 0-255 0
23 LED Color 3 Blue LED Intensity 0-255 0
24 LED Color 4 Red LED Intensity 0-255 0
25 LED Color 4 Green LED Intensity 0-255 0
26 LED Color 4 Blue LED Intensity 0-255 0
27 LED Color 5 Red LED Intensity 0-255 0
28 LED Color 5 Green LED Intensity 0-255 0
29 LED Color 5 Blue LED Intensity 0-255 0
30 LED Color 6 Red LED Intensity 0-255 0
31 LED Color 6 Green LED Intensity 0-255 0
32 LED Color 6 Blue LED Intensity 0-255 0
33 LED Color 7 Red LED Intensity 0-255 0
34 LED Color 7 Green LED Intensity 0-255 0
35 LED Color 7 Blue LED Intensity 0-255 0
36 LED Color 8 Red LED Intensity 0-255 0
37 LED Color 8 Green LED Intensity 0-255 0
38 LED Color 8 Blue LED Intensity 0-255 0
39 LED Color 9 Red LED Intensity 0-255 0
40 LED Color 9 Green LED Intensity 0-255 0
41 LED Color 9 Blue LED Intensity 0-255 0
42 LED Color 10 Red LED Intensity 0-255 0
43 LED Color 10 Green LED Intensity 0-255 0
44 LED Color 10 Blue LED Intensity 0-255 0
45 LED Color 11 Red LED Intensity 0-255 0
46 LED Color 11 Green LED Intensity 0-255 0
47 LED Color 11 Blue LED Intensity 0-255 0
48 LED Color 12 Red LED Intensity 0-255 0
49 LED Color 12 Green LED Intensity 0-255 0
50 LED Color 12 Blue LED Intensity 0-255 0
51 LED Color 1 White LED Intensity 0-255 0
52 LED Color 2 White LED Intensity 0-255 0
53 LED Color 3 White LED Intensity 0-255 0
54 LED Color 4 White LED Intensity 0-255 0
55 LED Color 5 White LED Intensity 0-255 0
56 LED Color 6 White LED Intensity 0-255 0
57 LED Color 7 White LED Intensity 0-255 0
58 LED Color 8 White LED Intensity 0-255 0
59 LED Color 9 White LED Intensity 0-255 0
60 LED Color 10 White LED Intensity 0-255 0
61 LED Color 11 White LED Intensity 0-255 0
62 LED Color 12 White LED Intensity 0-255 0
15

Tiltbot Trio
Part Number Descripon
1310PCBLEDMOD COMPLETE LED MODULE
1310PCBDRIA LED DRIVER A
1310PCBDRIB LED DRIVER B
1310PCBDISMAI MAIN PCB AND DISPLAY
1310PCBPOW POWER RELAY PCB
1310FAN FAN
1310POW POWER SUPPLY
1310LEDRGB SINGLE RGB LED
1310LEDWHI SINGLE WHITE LED
1310HOUSTI OVERLAY STICKER
1310HOUYOK HOUSING YOKE
1310HOUFAN METAL FAN HOUSING HOLDER
1310BEZARM PLASTIC ARM BEZEL
1310BEZFAN PLASTIC FAN COVER BEZEL
1310GLAFRO FRONT COVER GLASS
1310HOUGUI1 TILT YOKE ARM LOCATION RING
1310HOUMOT TILT MOTOR GEAR
1310CONPOW SEETRONIC POWER IN&OUT PANEL CON
1310CONSIG5 SEETRONIC SIGNAL IN&OUT 5PIN PANEL CON
1310CONSIG3 SEETRONIC SIGNAL IN&OUT 3PIN PANEL CON
1310MOTTIL TILT MOTOR
1310SEAFRO FRONT GLASS FRONT WEATHER SEAL
1310SEABACK FRONT GLASS BACK WEATHER SEAL
1310SEADIS DISPLAY WEATHER SEAL
Item List
16

Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to
be carried out by authorized dealers.
Replacing the fuse: When possible only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized
dealers or trained professional only.
Should you have further questions , please contact your dealer.
17
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector
has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
When mounting the fixture must be mounted in a way water will not sit on the panel
power or signal connections.

Mega-Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [email protected]g
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LED’s and LAMPS are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]
Document
Version Date Fixture Soware Notes
1.1 03/28/2020 V1.1
Manual Version
Please Visit www.mega.lighting for the most up to date manual version