MegaLite Drama LED Z50 WW User manual

USER MANUAL
Table of Contents
Safety Information 3
Specifications 4
Photometrics 5
Main Power Connection 6
DMX-512 Connection 6
Mounting Controller 7
DMX Profile 7
Main Control Menu 8
Rigging the Fixture 9
Cleaning & Maintenance 9

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured away from unit movement.
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. This unit must not remain on for long periods of time.
5. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

Technical Information
4
Part Numbers
Fixture
7058-Drama LED Z50 WW
Mechanical Specifications
Fixture Packaged for Shipping
Size: 16.5”L x 8”W x 12.5”H
Weight: 7.5 lb
Size: 19.25”X 7.5” X 7.5”
Weight: 9 lb
DMX Connectors: 3 or 5-pin XLR connectors in/out (specified at ordering)
Power Connections: Nema 5-15 to screw type base connector cable mounted
Thermal: Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Display:Digital
Fastening System: Single Mounting Yoke
Gobo Diameter: 45mm
Image Diameter: 25mm
Barrel Rotation: 90°
Electrical Specifications
LED Type: 1 COB LED
Color Temp: 3136K
CRI: 94.6
LED Watts: 50
LED Lifetime: 60,000 to 100,000 hours
Lens Options:19° to 36°
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Watts: 49
Amps: .65
PF: .63
Protocol: DMX 512
DMX Channels: 3 Mode of operation
Mode A 1 Channel On/Off
Mode P 1 Channel Dimmer
Mode F 2 Channel Dimmer/Strobe
Operating mode: Stand alone 255 step Dimmer setting via display on DMX controlled fixtures
Control & Programming
12.5”
8” (framing out)
16.5” (w/controller)

Photometrics
Output at Full
Lens Lumens at Full Output Eciency
18°1611 33lm/W
36° 1561 32lm/W
Lumens at Full Beam Angle 18°
Distance Foot Candles Beam Diameter
5' 810fc 1.6'
10' 203fc 3.1'
15' 90fc 4.7'
20' 51fc 6.3'
Lumens at Full Beam Angle 36°
Distance Foot Candles Beam Diameter
5' 239fc 3'
10' 60c 6.1'
15' 27fc 9.1'
20' 15fc 12.1'
5

6
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
DMX-512 Connection
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to
If you did not purchase the DMX controller 7057-CON-3 or 7057-CON-5 then this fixture will only turn off and on using
the switch on the rear of the fixture. You require a separate DMX controller to operate this fixture with DMX Signal. The
7057-CON-3 is equipped with a 3 pin In and Out Connection and the 7057-CON-5 is equipped with a 5 pin In and Out
Connection. You must specify when ordering that type of connection you require. The sockets are wired in parallel.
Only use a shielded twisted pair cable designed for RS-485 and 3 or 5 pin XLR plugs and connectors in order to connect
the controller with the fixture or the fixture with another.
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120 Ohm re-
sistor between the (-) and the (+) signal into a 3 or 5 pin XLR plug and plug it in to the last fixture
on the signal run. Pre-manufactured terminator plugs are available for purchase from your Mega-
Lite dealer (P-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
LN
110V—Connection LL 220V—Connection
1
2
3
2
3
1
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
5
3
4
2
11
2
3
4
5
4. N/A
5. N/A

7
Drama Z 50 Mode A
DMX Chanel Function Description Value
1On/Off LED off 0% 0-250
LED on 100% 251-255
Drama Z 50 Mode P
DMX Chanel Function Description Value
1Dimmer LED intensity (off to on) 0-255
Drama Z 50 Mode F
DMX Chanel Function Description Value
1Dimmer LED intensity 0-255
No Function 0-1
2Strobe Strobe (slow to fast) 2-196
Random Strobe (slow to fast) 197-242
Dimmer Full On 243-255
Mounting DMX Controller
DMX Profile
The mounting of the DMX controller should be mounted on the rear of the body. There is male USB Connection that
needs to align with the female base connection. The 2 thumb screws need to be tightened to secure the controller with
the fixture.

7
Main Control
If fixture was purchased with 7057-CON you will have Dimmer and DMX
Control over the fixture . The control board on the fixture is your inter-
face to access and control all the functions on the unit. Its digital display
gives you a code view of the options and functions. The following will
explain each function and its options.
ESC Up
Down
Enter
CONTROL BOARD
DMX Address
Press Enter to select the DMX start channel.
Use the up/down keys to select the required DMX start chan-
DMX Address Flash
1-512 0-255
Flash
This function allows you to strobe the LED’s in White color. Press Enter use the up/down keys to select desired flash
sped settings. Press Enter to confirm the settings.
Channel Mode
A-P-F
Mode A (1 Channels) Off/On
Mode P (1 Channels) Dimmer
Mode F (2 Channels) Dimmer, Strobe
Channel Mode
Press Enter to select the mode of operation.
Use the up/down keys to select the mode .
Dimming Curve
0-3
Dimming Curve
This function allows you to control the fade speed of the LED. Press Enter use the up/down keys to select desired fade
speed settings from 0 to 3. Press Enter to confirm the settings. (4 Steps) 0 will have no fade time 4 will be the slowest.
Display Control
This function allows you to control the display . Press Enter use the up/down keys to select on for the display to stay on
or off for the display to turn off after 10 second of no use . Press Enter to confirm the settings.
Display
On-Off
8
7
Control Knob
On the side of the control unit you will find a knob this knob is used to control the intensity of the LED. You can adjust the
value from Min to Max. (note knob will not work if DMX signal is active) If DMX signal is lost the knob control will take
over.

Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and
electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to
be carried out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized
dealers or trained professional only.
Should you have further questions , please contact your dealer.
9
Parts List
7057-PCB-MAI Main PCB card
7050-POW Power Supply
7050-CON-POW Male Power Head
7050-FAN Replacement fan
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector
has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
7057-KNO Knob Set
7057-CON-3DMX Controller 3 Pin
7057-CON-5DMX Controller 5 Pin
7050-ACC-GOB Gobo Holder
7050-ACC-GEL Gel Holder
Accessories ( included )
7058-LED LED
7058-PCB-DRI LED Driver
Accessories
7050-IRIS Removable Iris
7050-CAB- Power Cable

Mega-Lite
18668 Highway 16N
Helotes, Texas 78023
Ph 210-684-2600 Fax [phone]
www.mega.lighting / [email protected]g
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LED’s and LAMPS are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Customer Support
Mega Lite has a customer support line to provide set up help and to answer any question should you encounter a prob-
lem. Please visit our website for any other related technical documents. For service related issue please contact our
service dept.
Monday—Friday 9am to 6pm CST
Voice: 210-684-2600
E-mail: [e-mail]