MegaLite VAZT LED P100 User manual

USER MANUAL
Table of Contents
Safety Information……………………………………………………………………………………………. 3
Specifications……………………………………………………………………………………………………..4
Main Power Connection…………………………………………………………………………………..5
DMX-512 Connection…………………………………………………………………...……………...... 5
Main Control Menu.......................................................................................................... 6
DMX Profile......................................................................................................................... 8
Rigging the Fixture…………………………………………………………………………………………….9
Cleaning & Maintenance................................................................................................9
Parts List...............................................................................................................................9

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 140º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

4
4400–Vazt P100
Mechanical Specifications
Fixture Packaging
Size: 11” x 10.75” x 8.68
Weight: 6lb
Size: 10” x 10” x 14.6”
Weight: 7lb
Electrical Specifications
DMX 512 Protocol
DMX Modes: Mode A 3 Channels R,G,B
Mode P 5 Channels R,G,B,W,A
Mode H 8 Channels Dimmer R,G,B,W,A, Strobe, Macro
Control Options: Display preset setting
Control & Programming
DMX Connectors: 3 pin XLR connectors in and out
Thermal: Maximum ambient temperature 104°
Maximum surface temperature 140°
Fastening System: Double Mounting Yoke
Display: Digital
Power connection: Cable Mounted nema 5-15
LED Quantity: 1 Penta LED Red, Green, Blue, White, Amber
LED Watts: 100W
LED Lifetime: 60 to 100 thousand hours
LED Angle: 60°
Diffusion Angel: 80°
Refresh Rate: 1200 Hz
Power Input Voltage: 110V-240 50/60 Hz
Ballast: Electronic auto switching
Power Consumption: Watts: 115
Amps: 1.58
Part Numbers
10.75”
8.68”
11”
Technical Information

5
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
DMX-512 Connection
This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 240V from 50Hz to 60Hz
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded
twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or
the fixture with another.
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120
Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the
last fixture on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (HOS-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
1
2
3
2
3
1
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
LN
Main Power Connection

Display Menu
6
The control board on the fixture base is your interface to access and control
all the functions on the unit. Its digital display gives you a code view of the
options and functions. The following will explain each function and its options.
Press Enter to access the menu.
Menu Up Down
Enter
DMX Address
Red Dimmer Green Dimmer Blue Dimmer
Flash
Effects
0-255 0-255 0-255
White Dimmer
0-255
Amber Dimmer
0-255
Introduction
Dimming Speed
0
1
2
3
Set Color Menu
Red Fade Up
0-15
Green Fade Up
0-15
Blue Fade Up
0-15
White Fade Up
0-15
Amber Fade Up
0-15
Red Fade Down
0-15
Green Fade Down
0-15 0-15 0-15
Blue Fade Down White Fade Down
Amber Fade Down
0-15
Color Fade Up-Down
0-15
Color Fade
0-15
Color Fade+White
0-15 0-15
Color Snap
0-15
Color Snap Mix
Red Strobe
0-15
Green Strobe
0-15
Blue Strobe
0-15
White Strobe
0-15
Amber Strobe
0-15
Yellow Strobe
0-15
Cyan Strobe
0-15 0-15 0-15
Magenta Strobe RGBW Strobe
All on Strobe
0-15
Color Strobe
0-15
Color Ramping Strobe
0-15
Negative Strobe
0-15 0-15
Color+White Strobe
0-15
Random Color Strobe
001-512 001-512 001-512
AMode 3 Channels PMode 5 Channels HMode 8 Channels

7
Fade
This function allows you to select a preprogrammed fade sequences. Press Enter use the up/down keys to select desired fade
program (15 options). Press Enter to set the desired sped use the up/down keys (15 options). Press Enter to confirm the
settings.
Flash
Dimming Speed
Press Enter to select the desired dimming speed when used with a DMX controler. Use the up/down keys to select from 0 to 3.
0 speed will be the fastest 4 will be the slowest. Press Enter to confirm.
DMX Address
Press Enter to select the DMX start address channel. The first display will let you know what operation mode you are in. Use
the up/down keys to select the desired mode. Press Enter to confirm. (first Letter will also change depending on what mode you
are in) Use the up/down keys to select the desired start address press Enter to confirm
Set Color Menu
Press Enter to set a color via display control. . Use the up/down keys to select the desired color you would like to adjust. Press
Enter to confirm. Use the up/down keys to select the desired intensity of the color. Press Enter to confirm.
This function allows you to select a preprogrammed strobe sequences. Press Enter use the up/down keys to select desired
strobe program (15 options). Press Enter to set the desired sped use the up/down keys (15 options). Press Enter to confirm
the settings.
Menu Up Down Enter
Address mode
DMX Indicator
When DMX Signal is being received the last point on the control board display will turn flash. If
there is no DMX signal present is will be on.

8
DMX Profile
Vazt P100Mode A
DMX Chanel Function Description Value
1 LED Color Red LED intensity 0-255
2 LED Color Green LED Intensity 0-255
3 LED Color Blue LED Intensity 0-255
Vazt P100 Mode P
DMX Chanel Function Description Value
1 LED Color Red LED intensity 0-255
2 LED Color Green LED Intensity 0-255
3 LED Color Blue LED Intensity 0-255
4 LED Color White LED Intensity 0-255
5 LED Color Amber LED Intensity 0-255
Vazt P100 Mode H
DMX Chanel Function Description Value
1 Dimmer Dimmer Off to Full 0-255
2 LED Color Red LED intensity 0-255
3 LED Color Green LED Intensity 0-255
4 LED Color Blue LED Intensity 0-255
5 LED Color White LED Intensity 0-255
6 LED Color Amber LED Intensity 0-255
7 Strobe Strobe (slow to fast) 0-196
Random Strobe (slow to fast) 197-255
No Function 0-1
Color fade All (slow to fast) 2-19
Color Snap All (slow to fast) 20-39
Random Color Snap (slow to fast) 40-59
Red fade dim to full (slow to fast) 60-79
Green fade dim to full (slow to fast) 80-99
8 Macro Blue fade dim to full (slow to fast) 100-119
White fade dim to full (slow to fast) 120-139
Amber fade dim to full (slow to fast) 140-159
Red fade full to dim (slow to fast) 160-179
Green fade full to dim (slow to fast) 180-199
Blue fade full to dim (slow to fast) 200-219
White fade full to dim (slow to fast) 220-229
Amber fade full to dim (slow to fast) 230-249
Full On 250-255

9
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electron-
ics checked by an expert every year.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further
instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems
have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to be carried
out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or
trained professional only.
Should you have further questions , please contact your dealer.
Parts List
4400-MPCB Main PCB card
4400-PS Power Supply
4400-DIS Display
4400-DF Removable Diffusion Filter (included)
4400-FAN Replacement fan
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience includ-
ing but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifica-
tions, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has got to
be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least
one time a year by a skilled person.
4400-GH Gel Holder (included)
4400-KNOB Knob Set
Rigging the fixture
Cleaning and maintenance
Accessory
4400-BD Barn Door
4400-LED LED Replacement

Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax [phone]
www.mega-lite.com / [email protected]m
Warranty Information
Warranty Conditions
• Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
• LEDs are not guaranteed to match in color temperature or output.
• It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor. If
purchase date cannot be provided, date of manufacture will be used to determine warranty period.
• GOODS RETURNED UNDER WARRANTY MUST FOLLOW THE PROPER AUTHORIZATION PROCEDURE AND MUST BE
ACCOMPANIED BY A COPY OF THE ORIGINAL INVOICE
• Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment
• REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER. MEGA SYSTEMS INC. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO ANY
PRODUCT, AND MEGA SYSTEMS SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. MEGA SYSTEMS SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGE, INCLUDING LOST PROFITS, SUSTAINED OR INCURRED IN CONNECTION WITH ANY
PRODUCT OR CAUSED BY PRODUCT DEFECTS OR THE PARTIAL OR TOTAL FAILURE OF ANY PRODUCT
REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT
LIABILITY OR OTHERWISE, AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN.
• Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or
parts. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.