MegaLite Drama W LED User manual

USER MANUAL
Table of Contents
Safety Information……………………………………………………………………………………………. 3
Specifications……………………………………………………………………………………………………..4
Main Power Connection…………………………………………………………………………………..5
DMX-512 Connection…………………………………………………………………...……………......5
DMX Profile......................................................................................................................... 6
Main Control Menu.......................................................................................................... 7
Rigging the Fixture…………………………………………………………………………………………….8
Cleaning & Maintenance................................................................................................8
Parts List.............................................................................................................................. 8

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured away from unit movement.
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

Technical Information
4
Part Numbers
Fixture
7000-Drama LED W
Mechanical Specifications
Fixture Packaged for Shipping
Size: 23”L x 13.75”W x 19”H
Weight: 11 lbs
Size: 24.5”X 10.5”X 10.5
Weight: 13 lbs
DMX Connectors: 3-pin XLR connectors in/out
Power Connections: Nema 5-15 cable mounted connection
Thermal: Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Display: Digital
Fastening System: Mounting Yoke
Electrical Specifications
LED Type: 1 Wafer LED
LED Watts: 120
LED Lifetime: 60,000 to 100,000 hours
Lens Options:19°,26°,36° and 50°
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Watts: 295
Amps: 2.46
Protocol: DMX 512
DMX Channels: 3 Mode of operation
Mode A 1 Channel On/Off
Mode P 1 Channel Dimmer
Mode F 2 Channel Dimmer/Strobe
Operating mode: Stand alone 15 step Dimmer setting via display
Control & Programming
23”
13.75”Open 10.5”Closed
19”Open
17.5”Closed

5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
21
3
1
3
2
DMX-512 Connection
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to 60Hz
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded
twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or
the fixture with another.
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120
Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the
last fixture on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (HOS-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
220V
L
L
LN
110V—Connection LL 220V—Connection

6
Drama W Mode A
DMX Chanel Function Description Value
1 On/Off LED off 0% 0-250
LED on 100% 251-255
Drama W Mode P
DMX Chanel Function Description Value
1 Dimmer LED intensity (off to on) 0-255
Drama W Mode F
DMX Chanel Function Description Value
1 Dimmer LED intensity 0-255
No Function 0-1
2 Strobe Strobe (slow to fast) 2-196
Random Strobe (slow to fast) 197-242
Dimmer Full On 243-255
DMX Profile

7
Main Control Menu
The control board on the fixture base is your interface to access and control
all the functions on the unit. Its digital display gives you a code view of the
options and functions. The following will explain each function and its options.
ESC Up
Down
Enter
CONTROL BOARD
DMX Address
Press Enter to select. Use the up/down keys to select the required DMX start channel. Press Enter to confirm
DMX Address White Dimmer Flash
1-512 0-15 0-15
Mode A(1 Channels) On/Off
Mode P (1 Channels) Dimmer
Mode F (2 Channels) Dimmer/ Strobe
White Dimmer
This function allows you to dim the LED . Press Enter use the up/down keys to select desired dimmer settings. Press Enter then
ESC to confirm the settings. (15 Steps)
Channel Mode
This function allows you to select the operating mode
of the DMX channel profile. Press Enter use the up/
down keys to select desired Mode settings. Press
Enter to confirm the settings.
Channel Mode
A-P-F
Flash
This function allows you to strobe the LED. Press Enter use the up/down keys to select desired flash settings. Press Enter to
confirm the settings.

Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electron-
ics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further
instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems
have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to be carried
out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or
trained professional only.
Should you have further questions , please contact your dealer.
8
Parts List
7000-MPCB Main PCB card
7000-PS Power Supply
7000-DIS Display
7000-19 19 Degree Lens
7000-FANL Large Replacement fan
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience includ-
ing but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifica-
tions, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to
be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least
one time a year by a skilled person.
7000-26 26 Degree Lens
7000-36 36 Degree Lens
7000-50 50 Degree Lens
7000-KNOB Knob Set

Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax [phone]
www.mega-lite.com / [e-mail]
Warranty Information
Limited Warranty
Unless otherwise stated, your product is covered by a one year parts and labor limited warranty. Dichroic filters and glass gobos are not guaranteed
against breakage or scratches to coating. It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and dealer
or distributor. If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
Returning an Item Under Warranty for Repair
It is necessary to obtain a Return Material Authorization (RMA) number from your dealer or point of purchase BEFORE any units are returned for
repair. The manufacturer will make the final determination as to whether or not the unit is covered by warranty. Lamps are covered by the lamp
manufacturer’s warranty.
Any Product unit or parts returned to MEGA Systems Inc. must be packaged in a suitable manner to ensure the protection of such Product unit or
parts, and such package shall be clearly and prominently marked to indicate that the package contains returned Product units or parts and with an
RMA number. Accompany all returned Product units or parts with a written explanation of the alleged problem or malfunction. Ship returned Prod-
uct units or parts to: 5711 Kenwick St. San Antonio TX 78254 USA.
Note: Freight Damage Claims are invalid for fixtures shipped in non-factory boxes and packing materials.
Freight
All shipping will be paid by the purchaser. Items under warranty shall have return shipping paid by the manufacturer only in the Continental United
States. Under no circumstances will freight collect shipments be accepted. Prepaid shipping does not include rush expediting such as air freight. Air
freight can be sent customer collect in the Continental United States.
REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
MEGA SYSTEMS INC. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO ANY PRODUCT, AND MEGA SYS-
TEMS SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. MEGA
SYSTEMS SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGE, INCLUDING LOST PROF-
ITS, SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY PRODUCT DEFECTS OR THE PARTIAL
OR TOTAL FAILURE OF ANY PRODUCT REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN.
Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.