Megger Power Diagnostix ICMflex User manual

USER GUIDE
LANGUAGE | EN
ICMex
Partial discharge and loss factor measurement system

pdix.comUser guide for ICMex2
Power Diagnostix
NOTICE OF COPYRIGHT and PROPRIETARY RIGHTS
© Copyright 2023 by Power Diagnostix Instruments GmbH. All rights reserved.
The contents of this manual are the property of Power Diagnostix Instruments GmbH. No part of this work may
be reproduced or transmitted in any form or by any means without the written permission of the publisher.
Product and company names herein may be the trademarks of their respective owners.
Power Diagnostix reserves the right to alter the specication of its products from time to time without notice.
Although every effort is made to ensure the completeness and accuracy of the information contained within
this document, it is not warranted or represented by Power Diagnostix to be a complete and up-to-date de-
scription.
This manual supersedes all previous issues of this manual. Please ensure that you are using the most recent
issue of this document.

pdix.com User guide for ICMex 3
USER GUIDE
LANGUAGE | EN
ICMex
Partial discharge and loss factor measurement system

pdix.comUser guide for ICMex4
Contents
1 General ...................................................................................................................7
1.1 About this user guide .................................................................................................................... 7
1.2 Instrument safety........................................................................................................................... 7
1.3 Health and safety recommendations............................................................................................ 8
1.3.1 General safety procedures prior to testing............................................................................................8
1.3.2 Health and safety risks ..........................................................................................................................9
1.3.3 Environmental conditions ......................................................................................................................9
1.3.4 Lithium-ion battery module warnings ....................................................................................................9
2 Principle of operation ...........................................................................................10
3 Measurement set-up ............................................................................................13
3.1 Verifying the part list.................................................................................................................... 13
3.2 High voltage cabling.................................................................................................................... 13
3.3 Location ....................................................................................................................................... 14
3.4 Parts of the ICMex under high voltage potential...................................................................... 14
3.5 Connecting the ICMex.............................................................................................................14
4 Software and driver installation ...........................................................................17
4.1 Installing the ICMex software.................................................................................................... 17
4.2 Setting up a Bluetooth COM port................................................................................................ 18
4.3 Settingupabreopticcommunicationport(USBserialCOM)................................................ 19
5 ICMex software...................................................................................................21
5.1 First steps .................................................................................................................................... 21
5.2 Connecting to the instrument ..................................................................................................... 22
5.3 Firmwareupdatesandcongurationles .................................................................................. 23
5.4 Principle of operation .................................................................................................................. 24
5.4.1 PD display mode .................................................................................................................................24
5.4.2 LOC display mode...............................................................................................................................26
5.4.3 REC display mode...............................................................................................................................28
5.5 Display mode settings................................................................................................................. 30
5.5.1 Settings for partial discharge measurement .......................................................................................30
5.5.2 Settings for PD fault location ...............................................................................................................31
5.5.3 Settings for the record mode...............................................................................................................32

pdix.com User guide for ICMex 5
5.6 Functions and menus.................................................................................................................. 34
5.6.1 Menu items ..........................................................................................................................................34
5.6.2 Function keys ......................................................................................................................................37
5.7 ICMex and PD calibration ......................................................................................................... 39
5.7.1 Calibrators ...........................................................................................................................................39
5.8 Gating........................................................................................................................................... 41
5.8.1 Principle of operation...........................................................................................................................41
5.8.2 Analogue gating ..................................................................................................................................41
6 Application notes..................................................................................................43
6.1 Medium and high voltage cables................................................................................................ 43
6.1.1 Measurement set-up ...........................................................................................................................43
6.1.2 Calibration............................................................................................................................................43
6.1.3 Standard PD measurement.................................................................................................................46
6.1.4 PD measurements on cables with high capacitance..........................................................................47
6.1.5 PD fault location ..................................................................................................................................48
6.1.6 Test voltage recommendations and criteria........................................................................................50
6.1.7 Typical PD patterns and tandelta levels ............................................................................................52
6.1.8 Normative references ..........................................................................................................................53
6.2 Rotating machines....................................................................................................................... 54
6.2.1 Test set-up...........................................................................................................................................54
6.2.2 Calibration............................................................................................................................................54
6.2.3 PD measurements...............................................................................................................................55
6.2.4 Step-by-step guide..............................................................................................................................57
6.2.5 Typical PD patterns and tan delta levels on rotating machines..........................................................64
6.2.6 Normative references ..........................................................................................................................66
6.3 Stator bars ................................................................................................................................... 66
6.3.1 General ................................................................................................................................................66
6.3.2 Test set-up...........................................................................................................................................67
6.3.3 PD calibration ......................................................................................................................................67
6.3.4 PD and tan delta measurement ..........................................................................................................67
6.3.5 Typical patterns and tan delta levels on single stator bars.................................................................68
6.3.6 Normative References .........................................................................................................................68
Contents

pdix.comUser guide for ICMex6
7 Options .................................................................................................................69
7.1 GuardRingControl(GRC) .......................................................................................................... 69
7.2 AdditionalPDinputfornoisecancellation(ICMex2) ............................................................... 69
7.3 Gatingviabreopticlink(FOgating)......................................................................................... 75
7.4 Bypass ......................................................................................................................................... 78
7.5 Built-in RPA1L.............................................................................................................................. 78
7.6 External battery adapter.............................................................................................................. 78
8 Miscellaneous.......................................................................................................79
8.1 Maintenance ................................................................................................................................ 79
8.2 Productmarks ............................................................................................................................. 79
8.3 Transport and shipment instructions.......................................................................................... 79
8.3.1 Instrument............................................................................................................................................79
8.3.2 Batteries...............................................................................................................................................79
8.4 Declaration of Conformity ........................................................................................................... 80
8.5 UKDeclarationofConformity ..................................................................................................... 81
9 Technicaldata(standardversion) .......................................................................82
9.1 Cable fault location...................................................................................................................... 82
9.2 Loss factor measurement............................................................................................................ 82
9.3 Weight and Dimensions .............................................................................................................. 83
10 Appendix...............................................................................................................84
10.1 Whatisthelossfactor(ordissipationfactor)tandelta? ........................................................... 84
10.2 Troubleshooting .......................................................................................................................... 85
10.3 National Instruments hardening guide ....................................................................................... 87
10.3.1 Introduction..........................................................................................................................................87
10.3.2 Step-by-step guide..............................................................................................................................87
10.3.3 Service description ..............................................................................................................................88
11 Index .....................................................................................................................89
Contents

pdix.com User guide for ICMex 7
ICMex
Partial discharge and loss factor measurement system
zAlways provide solid grounding of the instrument. Use the wing nut terminal for
ground connection on the ground plate or the multi-contact connectors beside.
Never operate the instrument without protective grounding.
zAvoid working alone.
zDo not allow the instrument to be used if it is damaged or its safety is impaired.
zInspect the ground leads and signal cables for continuity.
zSelect the proper coupling circuit and connection for your application.
zDo not use the instrument in an environment that is at risk of explosion.
zUse the bre optic link or the Bluetooth communication to operate the instru-
ment.
zOnly use cables supplied by Power Diagnostix.
Warning
1 General
1.1 About this user guide
This user guide describes the hardware, software, and usage of the ICMex in its current version including
all available congurations. Some of the hardware features of the most recent versions are not available with
earlier versions of the instrument. It is possible to upgrade most of the previous instruments to the features of
the current instruments. Please contact Power Diagnostix for details ([email protected]).
Software updates are available through Power Diagnostix’ website (www.pdix.com). The access to the down-
load area of that website is password protected and requires a valid software maintenance contract. Please
contact Power Diagnostix for details. Current brochures and revisions of this manual are available for down-
load (PDF format) on that website as well.
1.2 Instrument safety
Before using the ICMex, read the following safety information in this manual carefully. In particular, read
and follow the information, which is marked with the words ‘Warning’ and ‘Caution’. The word ‘Warning’ is
reserved for conditions and actions that pose hazards to the user, while the word ‘Caution’ is reserved for
conditions and actions that may damage the instrument, or its accessories, or that may lead to malfunction.
Always obey the safety rules given with the warnings on the instrument and in this guide. Be particularly aware
of the safety issues that can arise while performing eld measurements. Never disregard safety considera-
tions, even under the time constraints often found with on-line and off-line tests on site.

pdix.comUser guide for ICMex8
ICMex
Partial discharge and loss factor measurement system
1.3 Health and safety recommendations
1.3.1 General safety procedures prior to testing
When working under high voltage conditions, following topics need to be considered strictly prior to the
measurement set-up and testing.
1. The operators must have read the safety instructions and passed the local site safety instructions regard-
ing health and possible hazards.
2. The sample to be tested must be ofine, de-energised, and grounded.
3. Each operator has to check the safety conditions together with the site responsible and pass the tagout/
lockout procedure for the specimen to be tested.
4. After the tagout/lockout procedure, the specimen needs to be checked for the presence of voltage to-
gether with the site responsible by using a suitable HV tester.
5. The operator has to check the solid work grounding together with the site responsible.
6. After passing issues 1) to 5), the specimen is in safe condition and may be connected to the equipment.
7. Check for a safe area as close as possible to the specimen terminals to install the equipment.
8. Apply demarcation around the full measurement set-up and make use of a safety guard, if necessary.
9. Prevent working alone.
10. Only authorised personnel are allowed to access the demarcated test area.
11. Hold a meeting with other people working close to the hazardous area before energising the test speci-
men.
12. Please check at least the insulation resistance prior to apply external HV potential.
13. Remove the calibrator before applying any external high voltage.
14. When applying external high voltage, carefully increase the voltage while observing if voltage and current
stay within predened limits.
15. Make sure that the sample is free of voltage after the external high voltage has been switched off.
16. Discharge and ground the test specimen with a grounding stick before changing or touching any HV
connection.
17. The specimen is now in safe condition, necessary changes to the set-up can be done safely.
Please check the detailed Power Diagnostix “Health and Safety Instructions and Recommendations” guide-
line in case of any ambiguities regarding safety.

pdix.com User guide for ICMex 9
ICMex
Partial discharge and loss factor measurement system
1.3.2 Health and safety risks
Incautious actions during testing can result in life-threatening hazards such as electrocution. Please be aware
that this risk applies for the operators as well as other people working close to the area under high voltage.
Please take the necessary personal protection recommendations as mentioned above and in the detailed
Power Diagnostix “Health and Safety Instructions and Recommendations” guideline so that testing can be
performed in a safe condition at any time.
A specimen under high voltage can produce Ozone due to the presence of partial discharge activity. The
maximal allowed Ozone concentration in the open air is xed on 0.1ppm (parts per million) in accordance
with the European Health commission. Inhalation of too much ozone can lead to severe lung problems in the
short and/or long term. Please make sure that the test area is sufciently ventilated. When necessary, make
use of any required personal protection equipment, and hence, consider this health recommendation during
testing.
1.3.3 Environmental conditions
Care must be taken that the area surrounding the test specimen is in sufciently clean and dry condition be-
fore installing the equipment and starting the tests. We recommend considering particularly the temperature
and relative humidity. Temperatures above 45 °C can directly affect the performance of the battery. Working
under too high humidity conditions can result in additional stray capacitances inuencing the tandelta and
capacitance values, as well as the partial discharge measurement. Always make sure that the equipment is
clean and leave sufcient space between the parts under high voltage and any other object nearby.
1.3.4 Lithium-ion battery module warnings
zThis instrument may be provided with a Lithium-ion high energy battery module.
zDo not pierce, damage, disassemble, or modify the battery module. The battery module contains safety
and protection devices which, if tampered with, may cause the battery to generate heat, to rupture, or to
ignite.
zIf a battery is suspected to be faulty, replace it with a Power Diagnostix approved battery module.
zIf an instrument is suspected to contain a faulty battery module, the module must be removed before the
instrument is shipped.
zDo not ship a faulty battery module, either separately or connected to an instrument.

pdix.comUser guide for ICMex10
ICMex
Partial discharge and loss factor measurement system
2 Principle of operation
The ICMex is a unique measurement system that covers PD detection, PD fault location on cables, and tan
delta measurements (standard ICMex, only). It has been designed to simplify the application and to combine
different measurement tasks with one instrument. This new principle minimises testing and operation time, in-
creases operator’s safety, and guarantees highest sensitivity and precision. Main users of these systems are:
zService groups testing motors, generators, and accessories of the same
zService groups testing high voltage cables, termination, and joints
zMaintenance and repair shops
zHigh voltage laboratories
zResearch and development departments
The system is mainly used for on-site testing but can be used in laboratories and workshops as well. It op-
erates with any xed or portable high voltage power supply, such as transformers, hi-pots, resonant test
systems, motor generator sets, and VLF systems (cos/square and sine waves). Power Diagnostix offers
complete systems as well as modular components.
A complete acquisition system is shown here in Figure 1. It con-
sists of a reference capacitor Cn, two shunt capacitors Csn and
Csx, a decoupling circuit for PD measurement, and the acquisi-
tion box with battery module. If PD measurement is not want-
ed, the decoupling circuit will not be built in. For systems above
30 kV the main box is surrounded by an aluminium electrode to
smoothen the electrical eld. The communication from a com-
puter to the instrument can be established via Bluetooth or via
bre optic serial bus. All measurement values are displayed by
the ICMex remote control software on the computer.
Two voltages can be measured with this system. Uxis taken from
the capacitive divider between the external capacitance of the
test object Cxand the internal shunt capacitor Csx. The reference
voltage Unis provided by the capacitive divider Cn/Csn. The wave-
form of both voltages is displayed in a special graph in parallel
with the absolute values of Upeak, Urms, and Upeak/sqrt2. The correla-
tion of both signals gives further results like the tan delta value,
the power factor, and the capacitance Cxof the sample under
test. Due to the high sampling rate of 100 kS with a 16-bit A/D
conversion, sufcient precision and accuracy can be guaran-
teed.
The high frequency PD signal is used for PD pattern acquisition as well as for PD fault location on cables, if
needed. The PD scope comes with an 8-bit resolution vs. phase and amplitude. The pulse counting goes up
to 65536 (16 bits) per phase-amplitude position. The sensitivity of PD measurements depends strongly on the
quality of the power supply. Power Diagnostix offers various modular lter units to block noise generated by
the source (see section 3.5). Furthermore, the instrument comes with a built-in gating input to trigger on HF
pulses from the input side. External noise signals do not interfere with the measurements as all signals are
directly taken on high voltage potential and, therefore, critical ground loops to the instrument are not existent.
Figure 1: Design of the ICMex

pdix.com User guide for ICMex 11
ICMex
Partial discharge and loss factor measurement system
The following table shows the most common combinations and congurations of the ICMex. Instruments for
higher voltages are available on request. Adaptable high voltage lters are available for all systems.
TYPE RATED
VOLTAGE
UR (RMS)
RATED
CURRENT
IR(RMS)
FREQUENCY
RANGE
F
REFERENCE
CAPACITOR
CN
SHUNT
CAPACITOR
CSN
SHUNT
CAPACITOR
CSX
ICMex
20 kV 1 A 2–265 Hz 1000 pF 2 µF 5 µF/30 µF
30 kV 5 A 2–265 Hz 1000 pF 3 µF 10 µF/100 µF
30 kV 100 mA 0.02–0.1 Hz
(2–265 Hz) 1000 pF 3 µF 40 µF/400 µF
50 kV 1 A 2–265 Hz 500 pF 2.5 µF 10 µF/100 µF
50 kV 100 mA 0.02–0.1 Hz
(2–265 Hz) 500 pF 4 µF 40 µF/400 µF
100 kV 1 A 2–265 Hz 1000 pF 10 µF 10 µF/100 µF
100vkV 100 mA 0.02–0.1 Hz
(2–265 Hz) 1000 pF 10 µF 40 µF/400 µF
150 kV 1 A 2–265 Hz 1000 pF 15vµF 10 µF/100 µF
150 kV 100 mA 0.02–0.1 Hz
(2–265 Hz) 1000 pF 15 µF 40 µF/400 µF
Typical lter units are listed in the table below. Please contact Power Diagnostix if modied versions are needed.
TYPE RATED
VOLTAGE
UR(RMS)
RATED
CURRENT
IR(RMS)
FREQUENCY
RANGE
F
FILTER
CONFIGU-
RATION
BLOCKING
CAPACITOR
CB
DAMPING
FACTOR
@100 KHZ
T30/1 30 kV 1 A DC–300 Hz L-C-L 6.7 nF >100
T50/1 50 kV 1 A DC–300 Hz L-C-L 10 nF >100
T100/1 100vkV 1 A DC–300 Hz L-C-L 10 nF >100
T100/70 100 kV 70 A DC–300 Hz L-C-L 10 nF >100
T150/1 150 kV 1 A DC–300 Hz L-C-L 10 nF >100

pdix.comUser guide for ICMex12
ICMex
Partial discharge and loss factor measurement system
The following Figure 2 shows a 50 kV set consisting of a T-lter T50/1 (left) and the ICMex model for 50 kV
(right).
Figure 2: 50 kV test set
Based on application necessity, it is possible to order the ICMex acquisition system in different congura-
tions. The following table illustrates this modularity. Please contact Power Diagnostix to specify the individual
conguration.
TYPE COMMENT
ICMex
Basic system
The basic system offers voltage measurement, frequency measurement, and both com-
munication ports (Bluetooth and bre optic serial transmission). The black acquisition
box is placed in the head of the grey case. The system is not usable without one of the
following options.
ICMex
Option TD
This option enables all features for loss factor measurements. The system will come
with customised shunt and reference capacitors. The software calculates the following
values:
Cx : Capacitance of the test object
tan δ: Loss factor of the sample under test
cos ϕ: Power factor of the sample under test
Optionally, the system can be tted with a Cxbypass to avoid overstressing of the shunt
capacitor if the test object’s capacitance is too high.
ICMex
Option PD
This option is needed if PD measurements shall be taken from the test object. The sys-
tem comes with a built-in measuring impedance on HV potential. The software displays
all PD activities in a PD scope graph, allows PD pattern acquisition, and indicates the
precise PD magnitude Qp.
ICMex
Option LOC
This option can be chosen in addition to the option PD. A special high-speed sampling
board with 16-bit 100 MS A/D converter enables the pulse measurement vs. time. This
option is mandatory for PD fault location on cables. The software offers a special TDR
(Time Domain Reectometry) graph and further evaluation tools.

pdix.com User guide for ICMex 13
ICMex
Partial discharge and loss factor measurement system
3 Measurement set-up
3.1 Verifying the part list
Before starting the installation, it is recommended to check if all parts are available. The standard package
consists of the following items:
zAcquisition unit ICMex,
zHV lter (optional),
zBattery pack type BAT2A,
zBattery charger,
zFibre optic cable (10 m); USB to Sub-D
zComputer incl. software ICMex,
zPD calibrator CAL1B or similar incl. connection set (optional),
zSet of cables:
}0.6 m HV cable (grey) with multi-contact connectors (male/female),
}1.5 m HV extension cable (grey) with multi-contact connectors (male/female)
}1.0 m HV cable (grey) with multi-contact connector (male) at one end and clamp connector at the other end,
}1.0 m grounding lead (yellow/green) with multi-contact connectors (male/female),
}1.5 m grounding lead (yellow/green) with multi-contact connector (male) at one end and clamp
connector at the other end,
}74 cm RG58 cable
zSet of spare connectors; type multi-contact (male),
zUser guide.
Please contact Power Diagnostix for spare parts or updates.
3.2 High voltage cabling
A set of high voltage cables is presented in Figure 3. Please be aware that the delivered high voltage cables
are non-shielded cables which must not touch or be close ground potential. The insulation of the high voltage
cables supplied by Power Diagnostix can withstand a maximum voltage of 13.8 kV with direct contact to
ground. However, the cable must be installed at a safe distance from any grounded objects. Surface dis-
charge activity will incept from 3 kV in case of direct contact. Please check the detailed Power Diagnostix
‘Health and Safety Instructions and Recommendations’. The minimum distances in open air conditions, which
are to be respected in relation to the applied voltage, are specied there in Appendix 3.
Figure 3: High voltage cables

pdix.comUser guide for ICMex14
ICMex
Partial discharge and loss factor measurement system
3.3 Location
As mentioned above in the general procedure prior to installation, please search for a safe location close the
specimen to install the equipment. Ask for a scaffold, delineation, or covered area, if required, as shown in
Figure 4, and prevent environmental conditions with high relative humidity and extreme temperatures.
3.4 Parts of the ICMex under high voltage potential
The ICMex is designed via a unique concept. The entire acquisition unit is directly placed on high voltage po-
tential right at the position where the necessary signals are. This offers the advantage that no additional signal
cables are needed. The lter units are constructed via the same principle. The parts that are on high voltage
potential are marked with warning signs to prevent confusion during set-up (see Figure 5 in section 3.5).
The complete head box, including the corona cage surrounding the top of the reference capacitor and both
MC connectors on the in- and output, is under high voltage potential. The bottom plate of the ICMex and
corresponding lter unit are at ground potential.
3.5 Connecting the ICMex
Please read the application notes for testing of medium and high voltage cables and rotating machines for
their specic set-up overview. In general, the main connections are explained below.
The appropriate connection of the HV source (HV transformer, resonance test set, VLF high potential) to the
lter and/or ICMex is mentioned on the top covers of both ltering unit and ICMex. Please follow the con-
nection indicators accordingly.
The HV cable of the power supply has to be connected to the female input connector of the lter (at the
left-hand side of Figure 5) or, if a lter is not needed, directly to the input of the ICMex. A bridge needs to
be established from the male output connector of the lter (at the right-hand side of Figure 5) to the female
connector of the ICMex. Finally, the male connector of the ICMex needs to be connected to the specimen.
This can be a motor terminal or the conductor of a shielded high voltage cable or a stator bar. Of course, the
interconnection between lter and ICMex is not necessary if no lter is used.
Figure 4: MV cable testing on-site

pdix.com User guide for ICMex 15
ICMex
Partial discharge and loss factor measurement system
The coaxial output of the lter (left picture in Figure 6) serves for the analogue noise gating. A noise decou-
pling circuit is directly built into the lter to capture any noise originating from the high voltage supply itself. A
coaxial connection between lter output and ICMex input (picture on the right-hand side of Figure 6) has to
be established for the use of the gating option. Please prevent direct contact between the coax cable and the
high voltage cable connecting lter and ICMex.
Figure 5: Filter connectors
Figure 6: Coaxial gating connector for lter (left) and ICMex (right)
Very important is the ground loop of the measurement
setup. A bad grounding has a strong inuence on the
sensitivity due to the background noise. The main
ground of the power supply has to be connected with
the ground terminal of the lter unit or in case no lter
is used, directly to the ICMex. Connection points are
foreseen on the metallic grounding plates, as shown
in Figure 7. The connection can be made by using a
cable lug or a multi-contact. Use the supplied short
cables to interconnect the grounding of the lter and the grounding of the ICMex and prevent any loop since
this will act as an antenna and inuence the noise behaviour. Finally, a connection, which should be as short
as possible, needs to be established between the ICMex and the main grounding of the test specimen.
Please choose a solid grounding and ensure a good contact. The interconnection between the grounding of
the lter and the ICMex is not necessary if no lter is used. A typical test setup is shown in Figure 9.
Figure 7: Ground connection points

pdix.comUser guide for ICMex16
ICMex
Partial discharge and loss factor measurement system
The most convenient way to communicate with the instrument is via
Bluetooth interface. Here, no further cabling is needed. In case, a
Bluetooth connection cannot be established, it is possible to use the
bre optic serial link instead. The SUB-D female connector of the ca-
ble has to be connected to the male connector on the upper side of
the ICMex (as shown in Figure 8). The USB connector of the cable
can be connected to any free USB port at the computer. As the bre
optic cable provides a galvanic separation from the high voltage po-
tential, there is no risk for the operator.
Caution and Warning: Never use a standard SUB-D cable without
galvanic separation. This can result in damage to components and
serious injury or death.
Figure 8: SUB-D input connector
Figure 9: General connection diagram for ICMex

pdix.com User guide for ICMex 17
ICMex
Partial discharge and loss factor measurement system
4 Software and driver installation
The ICMex comes with a Windows based software package on a USB stick or CD. The software can be in-
stalled on every Windows operating system of 32-bit or 64-bit architecture (version 7, 8, and 10). If a computer
is provided by Power Diagnostix, the software and the instrument drivers are pre-installed and readily cong-
ured. No further action is needed to start. In all other cases some preparations must be done as explained
next.
4.1 Installing the ICMex software
Please start the setup.exe le that can be found within the ICMex directory on the CD or USB stick. If a new
software version has been downloaded from the internet, it is mandatory to unzip all les to a local directory
on the target system rst. After starting the setup.exe le,
a window as shown in Figure 10 below will pop up.
Please choose individual installation directories, if want-
ed, and click ‘Next’. The installation kit automatically de-
tects earlier versions and updates only newer les pro-
vided by this release. This software has been developed
under National Instruments LabWindows/CVI. Therefore,
additional DLLs and libraries will be installed automati-
cally within the Windows system directory. Administrator
rights are necessary to complete the installation of this
software product. Please contact your system adminis-
trator in case insufcient rights are given on this ma-
chine. After nalising the software installation procedure,
the system restarts automatically.
The ICMex software can be started directly by clicking on the appropriate icon (as shown in
Figure 11) on the desktop. Before starting to communicate with the instrument further prepa-
rations must be completed as it will be explained next.
Figure 10: Software installation setup
Figure 11: Desktop icon

pdix.comUser guide for ICMex18
ICMex
Partial discharge and loss factor measurement system
4.2 Setting up a Bluetooth COM port
All Bluetooth devices on computer systems can provide so called virtual COM ports. These COM ports will be
used to establish a connection with the ICMex. Standard laptops come with built-in Bluetooth interfaces. If
not, it is possible to use external USB-Bluetooth devices. Power Diagnostix can provide such devices for USB,
PCI, or other interfaces, if needed. The Bluetooth interface on any computer provides an automatic scanning
function. Please start this procedure to nd the ICMex Bluetooth device.
Figure 12: Bluetooth connection wizard Figure 13: Adding a Bluetooth device
The express mode will guide through this setup (Figure 12). Click ‘Next’. The search routine can take a few
minutes. A pop-up window will display all devices found in range (Figure 13). Select the ‘ICMex’ entry and
continue the installation procedure (Figure 14).
It is mandatory to set the device code (Figure 15) for the ICMex connection to “0000”.
Figure 14: Bluetooth device successfully added Figure 15: Entering pairing code

pdix.com User guide for ICMex 19
ICMex
Partial discharge and loss factor measurement system
Figure 16: Device manager
If successful, the hardware manager of Windows will automatically install a virtual COM port for the new device.
Typically, two COM ports will be installed for the ICMex as shown in Figure 16. Enable both ports with the
ICMex software interface settings as described in section5.2.
4.3 Setting up a bre optic communication port (USB serial COM)
The ICMex comes with a special bre optic cable. The SUB-D male connector has to be connected to the
COM TTL female connector of the instrument box. The case of the SUB-D plug contains the hard-wire con-
nection to the bre optic converter. The default length of this cable is 10 meters. Individual lengths can be
supplied on demand. The side with the USB-A connector contains a bre optic to USB converter. This end
can be connected to any free USB port of the laptop or PC. The driver for the bre optic cable will be installed
with the software. Please do not connect the cable with the computer before the software is installed! If the
driver is not installed correctly, Windows will start the Hardware Installation Wizard (as shown in Figure 17)
when connecting the USB connector for the rst time to the computer.
To guarantee a correct installation, it is recommended to perform this installation procedure while being con-
nected with the internet. The Windows hardware manager searches the Windows driver library on the internet
to nd a suitable driver for this new device. Please contact Power Diagnostix in case of any problems.
Figure 17: Driver installation wizard

pdix.comUser guide for ICMex20
ICMex
Partial discharge and loss factor measurement system
If the computer does not recognise the cable, you need to install the drivers manually. Go to the device
manager and select the related COM port. After a right mouse click you can select ‘Update driver’. A window
comparable to Figure 18 will pop up. You can nd the driver in a subfolder named ‘USBDriver\CP210x’ in
your ICMex software installation directory, e.g.,
C:\pdix\Software\ICMex\ICMex.186]\USBDriver\CP210x.
Figure 18: Driver installation
This procedure must be performed twice: A rst time for the USB cable itself and a second time for the cable
converter.
The setup routine will automatically install the USB serial COM port, if found, and a new COM port (e.g.,
COM7) will be displayed with the device manager.
Figure 19: Device Manager
Please note that the COM port number has to be enabled within the interface settings of the ICMex software
(see section5.2). After a restart of the computer the software will automatically search for the COM port in
use. If the software can’t nd the COM port, you can check manually in the device manager as shown in
Figure 19.