Members Mark BQ05051-3 User manual

1
Grill Guide
For Model BQ05051-3
LP Gas Barbecue Grill
FOR YOUR SAFETY:
1. Read this Grill Guide before attempting to assemble or operate your grill.
2. Follow all safety instructions.
3. Check for leaks according to directions in this Grill Guide before operating your grill,
even if purchasing an assembled grill.
4. Keep this Grill Guide for future reference.
5. Contact 1-800-933-0527 should you need assembly assistance or have any questions.
THIS GRILL IS FOR OUTDOOR USE ONLY.
If stored indoors, then detach and leave propane cylinder outside.
STOP!
Missing A Part? No Need
To Go Back To The Store!
The store where you made the purchase does not stock
parts for this item. If you need parts, whether they are
missing or damaged, please call our Toll Free Help Line 1-800-933-0527.
Call us between 8:30 AM and 5:00 PM Central Time, Monday through Friday.

2
Safety Precautions
Always read and follow all DANGER, WARNING, AND FOR YOUR SAFETY notices in this Grill
Guide. Failure to do may result in serious bodily injury or death, or in a fire or an explosion causing
damage to property.
1. Grill installation must conform with local codes or, in the absence of local codes, with either the
National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA
B149.1, or Propane Storage and Handling Code, B149.2.
2. This gas grill, when installed, must be electrically grounded in accordance with local codes or , in
the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian
Electrical Code, CSA C22.1. This applies if an external electrical source is utilized.
3. This gas grill shall be used only outdoors, and not be used in a building, garage, or any other
enclosed area.
4. This gas grill is not intended to be installed in or on recreational vehicles and/or boats.
5. Never use any other type of fuel for this grill other than LP gas.
6. Only use the pressure regulator with a type 1 connector that is supplied with this gas grill.
7. Inspect the gas hose before each use. If it is evident there is excessive abrasion or wear, or the hose
is cut, it must be replaced prior to the gas grill being put into operation. The replacement hose
assembly shall be that specified by the manufacturer.
8. Always perform a Leak Test before operating your grill.
WARNING
1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
TO THE INSTALLER OR PERSON ASSEMBLYING THIS GRILL:
Leave this Grill Guide with the consumer.
TO THE CONSUMER:
Retain this Grill Guide for future reference.
!
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from appliance and immediately call your gas supplier or your
fire department.
!
WARNING
Combustion by-products produced when using this product contain chemicals known to the State
of California to cause cancer, birth defects, and other reproductive harm.
!

3
Table of Contents
Safety Precautions……….……………………………..……………...…………...…… 2
Table of Contents…………………….…………………………………..……….……...3
Warranty……………………………….………………………………………….…….. 4
Customer Support Center……………….………………………………………….…….4
Assembly Instructions...…………………………………………………………..…..5-13
General Information and Operation………………..………………………………..14-23
Trouble Shooting Guide……………………………………………….................….23-24
Write down here and keep for future
reference
Date of Purchase: _________________
Serial Number: ___________________
The serial number may be found on the placard located
on the back of the grill
BQ05051-3
Sam’s Club
608 Southwest 8th Street
Bentonville, AR 72712
1-888-746-7726
Visit us at : www.samsclub.com

4
The manufacturer warrants to the original
consumer-purchaser that this product shall be
free from defects in workmanship and materials
under normal and reasonable use when
assembled and operated according to this Grill
Guide from date of purchase as follows:
One year except as noted below:
Stainless Steel Burners - 3 years
Cast Aluminum and Stainless Steel Cabinet
Parts and Control Panel – 5 years
The manufacturer will, at its option, refinish or
replace any product or part found to be defective
during the limited warranty period. There may
be a shipping charge. The manufacturer may
require you to return the part(s) claimed to be
defective for its inspection, freight or postage
prepaid. Contact our Customer Support Center as
shown below before returning any part(s).
Additional information can be obtained by
writing:
Barbecue Grills
Warranty Department
1375 Mitchell Blvd
Schaumburg, IL 60126
The manufacturer will require reasonable proof
of purchase. We strongly recommend you
keep your sales receipt and register your grill.
You can attach your receipt to this guide.
This limited warranty does not cover the cost of
any inconvenience or property damage due to
failure of the product and does not cover damage
due to misuse, abuse, alteration, improper or
failure to perform normal and routine
maintenance, discoloration, accident, or damage
arising out of transportation of the product. This
limited warranty will not apply to any grill used
for commercial use.
This limited warranty is the sole warranty given
by the manufacturer and is in lieu of all other
warranties; express or implied, including implied
warranty of merchantability or fitness for a
particular purpose. Neither manufacturer dealers
nor the retail establishment selling this product
have any authority to make any warranties or to
promise remedies in addition to or inconsistent
with those stated above.
This limited warranty applies only to products
sold at retail, and is not transferable.
The manufacturer's maximum liability, in any
event, shall not exceed the purchase price of the
product paid by the original consumer-purchaser.
Some states do not allow the exclusion or
limitation of incidental or consequential damages.
Therefore, the above limitations or exclusions
may not apply to you. This warranty gives you
specific legal rights and may also have other
rights, which vary from state to state.
Limited Warranty
Customer Support Center
Thanks for purchasing a Member’s Mark™ Grill. We’re here to help you maximize your enjoyment an
d
appreciation of your new grill. Please don’t hesitate to contact us should you have any questions regarding
assembly, performance, warranty, or accessories. Please have your model number ready before you contact us.
We have a full line of replacement parts available. We’re here to serve You!
• If you need assistance or to order parts: Call 1-800-933-0527 or send a FAX to 1-847-252-1001.
• Business hours: Monday through Friday; 8:30AM-5:00PM Central Time.
• Visit us on the web at: www.omahagrills.com

5
Assembly Instructions
This page will give you an overview of information to assemble your grill. The following pages will show in
step-by-step detail how to do so. We offer the following suggestions to make your grill assembly as easy as
possible.
1.) Read through the entire Assembly Instructions before you begin.
2.) Choose an area large enough to comfortably lay out all the parts and hardware with enough room to easily
maneuver.
3.) Have an area with a non-abrasive surface where you can lay parts without scratching them.
4.) Use 2 people to remove the Cabinet and Firebox Assembly from the carton.
5.) Lay all parts and hardware out and ensure you have everything listed on the Parts and Hardware page before
you begin assembly. See the Customer Support Page for contact information should any parts be damaged or
missing.
6.) A Phillips Head Screwdriver has been provided for assembly.
7.) Do not use a Power Screwdriver for assembly as you could strip the threads on the Nuts and Bolts.
8.) The propane tank for this grill is sold separately. See the LP Gas and Cylinder Information later in this
guide.
BQ05051-3
!
WARNING
Failure to follow all Danger,
Warnings, and For Your Safety
notices in this Grill Guide may
result in serious bodily injury o
r
death, or in a fire or an explosion
causin
g
dama
g
e to
p
ro
p
ert
y
.
!
CAUTION
Perform the Leak Test explained
later in this Grill Guide before
operating your grill.

6
BQ05051-3 Detail Parts List
1 Thermometer 26 Firebox – Right Side Panel
2 Thermometer Seat 27 Cabinet – Left Side Panel
3 Hood 28 Cabinet – Back Panel
4 Silicon Stopper 29 Cabinet – Right Side Panel
5 Hood Handle Support 30 Glide Mounting Bracket - Left
6 Hood Handle 31 Glide
7 Side Shelf 32 Glide Mounting Bracket - Right
8 Side Shelf Handle 33 Cylinder Support Ring
9 Firebox – Back Panel 34 Cabinet Crossbar
10 Firebox – Left Side Panel 35 Condiment Box
11 Main Burner Bracket 36 Cylinder Drawer
12 Inner Heat Shield 37 Cabinet Bottom Shelf
13 Grease Tray 38 Swivel Caster
14 Gas Manifold Assembly 39 Caster
15 Bottom Heat Shield 40 Firebox Rear Panel
16 Firebox – Front Panel 41 Heat Pad - Right
17 Heat Shield for Control Panel 42 Heat Pad - Left
18 Control Panel 43 Locking Caster
19 Control Knob Seat 44 Locking Swivel Caster
20 Control Knob 45 Gas Hose Support Ring
21 Firebox – Back-Top Panel 46 Hood Bolt
22 Stamped Warming Rack 47 Manual Igniter
23 Cooking Grate 48 Burner Screw
24 Heat Diffuser 49 Regulator and Hose Assembly
25 Main Burner

7
BQ05051-3 Detail Parts List

8
Assembly Parts List
1. Cabinet and Firebox
Assembly..1PC
2. Heat Diffuser…3PCS 3. Cooking Grate…2PCS
4. Stamped Warming Rack…1PC
5. Side Shelf Assembly…2PCS 6. Side Shelf Handle…2PCS
Hardware List
A Phillips Head Bolt M6*3/8”L
8PCS D Phillips Head Bolt M6*5/8”L 4PCS
B Lock Washer 12PCS
C Phillips Head Screwdriver 1PC

9
STEP 1
Use 2 Phillips Head Bolts (D) and 2 Lock Washers (B) to attach Side Shelf Handle to Side Shelf
Assembly. Repeat the same procedure to attach the second Side Shelf Handle to the second Side
Shelf Assembly.
STEP 2
Use 4 Phillips Head Bolts (A) and 4 Lock Washers (B) to attach Right Side Shelf Assembly to
Cabinet and Firebox Assembly.

10
STEP 3
Use 4 Phillips Head Bolts (A) and 4 Lock Washers (B) to attach Left Side Shelf Assembly to Cabinet
and Firebox Assembly.
STEP 4
Place Heat Diffusers (2) in the Firebox in the appropriate slots.

11
STEP 5
Place Cooking Grates (3) on the inner lip of the Firebox.
STEP 6
Insert the Stamped Warming Rack (4) into the upper sides of the firebox. Be sure the sides of the
warming rack fit down into the slots to secure it in place.

12
STEP 7
Slide out the Cylinder Drawer and remove the Condiment Box as shown below.
STEP 8
Pull the Cylinder Support Ring up to the top of the cabinet. Place the LP Cylinder down into the
tank support hole. Unhook the LP Cylinder Support Ring and lower it over the top of the Cylinder.
Wrap it around the neck of the cylinder and reconnect as shown. Then attach the Condiment
Box to the back of the front drawer panel.
1

13
STEP 9
Connect the Regulator to the LP Cylinder Tank and slide the Cylinder Drawer closed.
STEP 10
Remove any labels and additional packing material from the grill. Be sure to clean all foam packing
material out of all areas.
Congratulations! Your grill is now fully assembled. Please proceed and read the General
Information and Operation portion of the Grill Guide before operating your new grill.

14
General Information and Instructions
Your new Grill has been designed and manufactured to high quality standards. It will provide you with many
years of enjoyment with a minimal amount of maintenance. Please keep in mind the following FOR YOUR
SAFETY.
OPERATION
1. Your gas grill requires reasonable care during operation. It will be hot during cooking and cleaning.
You should never leave the grill unattended or move the grill when in use.
2. Children should never use your gas grill. Keep younger children and pets away when in use.
3. Only use your gas grill outside in a well-ventilated area. Never use indoors in any building, garage,
shed, or under any type of flammable canopy or overhang.
4. Ensure your grill is on level ground and the locking casters are locked before use. Lock the
locking casters by pressing or turning the locking lever on the casters counterclockwise before
use. Unlock by turning or pressing the locking lever on the casters clockwise.
5. Turn all gas valves off should the burners go out when cooking. Open the lid and wait
5 minutes before relighting.
6. Do not lean over the grill or touch the edges of the firebox or lid when in use.
7. Turn the burners off, close the lid, and shut off the LP cylinder should a grease fire occur.
8. Do not obstruct the flow of combustion and ventilation air to this grill.
9. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
10. Keep the outdoor cooking gas appliance area clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
11. Do not put a barbecue cover or other flammable material in the storage area of this grill.
12. Do not use charcoal briquettes, lava rock, or any type of ceramic product in this grill.
LP Gas and Cylinder Information
Your new gas grill operates on LP (Liquid Petroleum) Gas. It is odorless, colorless, and non-toxic when
produced. You can smell LP gas as it has been given an odor similar to rotten cabbage for your safety.
Your grill uses the newest and safest LP Gas Cylinder.
1. A listed O.P.D. (Overfill Protection Device) – prevents accidental gas leaks
caused by overfilling of the tank. Each tank contains a float that
closes the input valve when the tank is 80% full. This allows room
for the LP gas to expand in hot temperatures. A triangular hand wheel
distinguishes this type of tank.
2. O.C.C.1 Type 1 Quick Connect Valve – provides fast tank hook-ups and requires only to be tightened by
hand. This is distinguished by large external threads on the outlet part of the valve.
In addition, the LP tank you use with your grill must meet the following requirements
1. Required Measurements: 12-1/2” (317mm) in diameter and 18-1/2” (472mm) in height.
2. 20-pound (9.1kg) propane cylinder.
3. Constructed and marked with U.S. Department of Transportation (D.O.T.) for the US or CAN/CSA-
B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, for
Canada.
4. A safety release valve.
5. A means for vapor withdrawal.
6. A collar to protect the tank valve.
7. A bottom ring for mounting.
Triangular Hand Wheel

15
LP CYLINDER FILLING AND EXCHANGE
Some areas only allow you to exchange your empty cylinder for a replacement that is already full. Other areas
allow you to refill your cylinder. If you are in an area where you can refill your cylinder:
1. Use only a licensed dealer.
2. The dealer must first purge a new cylinder before filling.
3. Never fill a cylinder more than 80% full by volume. Volume will vary by temperature. An empty
cylinder weighs approximately 18 pounds (8.2kgs).
4. Be sure the LP dealer checks the cylinder for leaks after filling.
5. Do not release LP gas into the atmosphere, as it can unexpectedly ignite when mixed with air.
6. Contact a LP dealer to remove LP gas from a cylinder.
7. Only exchange your cylinder for one with an O.P.D. feature as shown above.
LP CYLINDER LEAK TEST
A leak test should be done each time a cylinder is refilled or exchanged. Do
not smoke or use any type of flammable material in the area during this leak test.
Do not use an open flame to check for leaks.
1. Test outside in a well ventilated area.
2. Use a paintbrush and a solution of 50% liquid soap and 50% water. Do
not use cleaning agents and they can damage the fuel supply parts.
3. Brush liquid onto areas highlighted with arrows.
4. Bubbles indicate a leak.
!
WARNING
1. Do not attempt to use a cylinder with any other type of connection device.
2. Do not attempt to use a cylinder with a larger capacity
!
WARNING
A frosty cylinder valve indicates possible gas overfill. Close the LP valve and call your dealer
imm
ed
i
ate
l
y.
!
WARNING
1. Never store any extra cylinders under or near your grill.
2. Never fill your cylinder over 80% full by volume. This may cause release of gas from the safety
release valve.
3. If the information in points 1 and 2 above is not followed exactly, a fire causing death or serious
injury may occur.
4. Immediately call your LP dealer or fire department should you hear, smell, or see escaping gas
from the cylinder.
5. Do not insert an
y
t
yp
e of forei
g
n ob
j
ects into the valve outlet.
The gas supply must be turned off at the LP-gas supply cylinder when this outdoor cooking gas
appliance is not in use.

16
TRANSPORTATION AND STORAGE
1. Place dust cap on cylinder valve outlet whenever the cylinder is not in use.
Only install the type of dust cap on the cylinder valve outlet that
is provided with the cylinder of Propane Valve. Other types of caps
or plugs may result in leakage.
2. Always transport in an upright position.
3. Do not smoke when transporting your cylinder.
4. Keep cylinders out of direct sunlight and away from sources of heat.
5. Cylinders must be stored outdoors out of the reach of children and must not be stored in a building,
garage, or any other enclosed area.
Regulator and LP Cylinder Connections
Your regulator is equipped with a Q.C.C. Type 1 quick connect system. It will not allow gas to flow until a
positive seal has been made. It also has a flow-limiting device that will restrict the flow of gas to 10 cubic feet
per hour (0.28 cubic meters per hour).
TO CONNECT THE CYLINDER TO THE REGULATOR AND HOSE
1. Be sure the LP cylinder is “OFF” by turning the hand wheel clockwise
until it stops.
2. Place the cylinder into the drawer base of the grill with the valve
facing outward and secure with the cylinder support ring.
3. Be sure all burner controls are turned to the “Off” position.
4. Remove the safety cap from the from the cylinder valve.
5. Center the nipple of the regulator into the cylinder valve
6. Turn the black nut clockwise until it stops. Hand Tighten Only.
Do Not Use A Wrench.
!
CAUTION
The gas pressure regulator provided with this outdoor cooking appliance must be used. This regulator is
set for an outlet pressure of 11 inches water column. Replacement pressure regulators and hose
assemblies must be those specified in the parts list.
!
DANGER
B
ubb
l
es
in
d
i
cate
a
l
ea
k
.
In
t
h
at
case,
ca
ll
you
r LP
dea
l
e
r
o
r fir
e
depa
r
t
m
e
n
t
imm
ed
i
ate
l
y.
Dust Cap

17
LEAK TESTING THE REGULATOR, VALVES, HOSES, AND CONNECTIONS
1. Ensure the LP cylinder valve and all burners are “Off”.
2. Ensure the LP cylinder is connected to the regulator.
3. Mix up a solution of 50% water and 50% liquid dish soap. Do not use any household cleaner
solution.
4. Open the LP tank valve by turning the hand wheel counterclockwise one turn. If you hear a rushing
sound, turn the gas off immediately. In that case, there could be a leak at the connection. Reconnect
the cylinder to the regulator.
5. Spray or brush on the solution covering the following areas: cylinder welds, regulator and cylinder
connection, gas hose connections to the regulator, all gas hoses, all gas hose connections to the
burners including the main and side burners.
6. Growing bubbles on any of the parts and connections listed above indicate a gas leak. Immediately
shut off the LP tank valve by turning the valve clockwise. Retighten the connections or order
replacement parts as needed. Continue to test as necessary until no leaks are detected.
7. Close the LP tank valve by turning the hand wheel clockwise.
!
WARNING
1. Do not connect this grill to any unregulated sources of propane.
2. Protect the regulator fitting from damage when disconnected. A damaged regulator fitting may
result in a gas leak when connected to a LP cylinder.
3. Inspect the gas hose before each use. Replace the hose assembly before use if you notice any
fraying, cracking, or excessive wear.
4. Always perform the Leak Test listed below before using your grill for the first time, if the cylinder
has been changed, any gas components have been changed, the regulator flow-limiting device has
been activated, or after a long period of non-use.
5. Do not attempt to connect this grill to the LP system of a motor home or trailer.
Center this nipple of the
regulator into the cylinder
valve.
The regulator must enter the
cylinder valve in a straight
line.
!
WARNING
1. DO NOT USE THE GRILL if you cannot stop a leak. Be sure the LP cylinder valve is closed. If
the LP cylinder is still leaking, contact your LP dealer or local fire department.
2. Do not use any match or open flame, or smoke, during leak testing.
3. Do not light a burner during leak testing.
Q.C.C.1 Type 1 Connector
!
WARNING
Always keep the gas cylinder in
the u
p
ri
g
ht
p
osition all the time

18
Grill Placement
Grill Operations
LIGHTING
Always visually inspect your grill before lighting. Replace any hoses that are frayed or cracked before lighting
your grill. Look for anything that may be blocking spaces for ventilation and remove. After lighting, always
check the flame to ensure you have a good flame all along each burner. If not able to light, or the flame is not
even along the entire burner(s), then see the Trouble Shooting section.
!
FOR YOUR SAFETY
1. Minimum clearance required from sides and back of unit to adjacent combustible construction is 24
inches (61 cm).
2. Do not locate or use this outdoor cooking gas appliance under unprotected overhead combustible
surfaces.
APARTMENT RESIDENTS
Check with your apartment manager regarding
your regulations for barbecues.
!
WARNING
Keep any electrical supply cord and the fuel
supply hose away from any heated surfaces and
water.
!
WARNING
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5 minutes and repeat the
lighting procedure
24"(61cm)
24"(61cm)

19
LIGHTING THE MAIN BURNERS USING PUSH AND TURN IGNITION
1. Open the lid.
2. Ensure all burner control knobs are in the “Off” position.
3. Turn on the LP gas by slowly turning the hand wheel on the cylinder valve.
4. Push in the burner control knob of the burner you wish to light
and turn left to “HI/LIGHT”. You will hear a click as a spark is sent
to the burner. If the burner does not light, then turn back to “Off”,
and repeat this procedure. Continue this process until the burner
lights.
5. Use the Manual directions if it still will not light.
6. When lit, turn the burner control knob to its desired heat setting.
MANUALLY LIGHTING THE MAIN BURNERS WITH THE MATCH HOLDER
1. Open the lid.
2. Ensure all burners are in the “Off” position.
3. Slowly turn on the gas at the LP cylinder valve if it is not already on.
4. Place a match in the Match Holder. This is located in the condiment
box in the cylinder drawer.
5. Strike the match, and insert into the lighting hole close to the burner.
6. Turn the left burner control knob to “HIGH/LIGHT”.
7. If the burner does not light within 5 seconds, turn the burner control
knob to “Off”. Wait 5 minutes for gas to clear, and try again.
8. When lit, turn the control knob to the desired heat setting.
TURNING OFF YOUR GRILL
1. Turn all burner control knobs to the “Off” position.
2. Turn off the gas supply at the LP tank by turning the valve clockwise.
Cleaning Your Grill
!
WARNING
1. Do not clean any part of your barbecue grill in a self-cleaning oven.
2. Do not use oven cleaners, abrasive kitchen cleaners, cleaners that contain citrus products, or
mineral spirits.
3. Do not use any type of steel bristled brush.
4. Clean your grill regularly to prohibit grease build-ups and avoid a grease fire or excessive flare-
ups.
Main Burner

20
STAINLESS STEEL SURFACES AND OTHER EXTERIOR SURFACES– wash with a mild dish soap
and warm water. A cloth, soft brush, or plastic cleaning pad can be used. Rinse thoroughly and wipe dry. The
stainless steel used in the construction of your grill is 304 commercial grade. There are many specific stainless
steel cleaners available. Follow the manufacturer’s directions. Always polish in the direction of the lines. Do
not allow dirt and grease to accumulate. Do not use steel wool as it will scratch the surface.
COOKING GRATES, WARMING RACK, AND HEAT DIFFUSERS – use a stiff brass brush. Wash with
warm water and mild dish soap as needed, rinse, and dry.
GREASE PAN AND TRAY – check after each use. Remove and empty the Tray when half full. Remove and
clean the Pan as grease builds up. Both can be washed with warm water and mild dish soap.
BURNERS – we recommend you clean your burners at least twice a year, or before use if the grill has not been
used in over one month.
CLEANING THE BURNERS
1. Ensure the LP gas is turned off at the LP cylinder.
2. Remove the cooking grates, heat diffusers, and grease tray.
3. Remove the Phillips Head screws located at the back end of each burner. Remove the nut and bolt
which secures the burner to the electronic igniter.
4. Lift each burner up and out.
5. Clean the inside of the burner using a stiff wire. A straightened coat hanger is one suggested tool. An
alternative way to clean the inside of the burner is using compressed air. Always wear eye protection if
using this method. Never enlarge the burner ports during cleaning.
6. Brush the outer surface of the burner.
7. Ensure all ports (holes) are free of all debris
8. Inspect the burner. Replace if any cracks or enlarged holes.
9. Reinstall the burners making sure the burners seat over the
valves as shown in the figure to the right.
10. Secure the back of the burners to the firebox with the Phillips
Head screws and reattach to the electronic igniters.
11. Replace the grease tray, heat diffusers, and cooking grates.
12. Perform a Leak Test described earlier in this guide.
!
WARNING
Small insects, such as spiders, are able to access the burner tubes. Sometimes they will build nests or spin
webs. In either case, this can block or reduce the amount of gas flowing through the burner. You will
usually see a smaller flame, or a flame that is mostly yellow rather than blue, coming from the burner when
this happens. Other signs include the gill not heating evenly, not reaching temperature, or burners not
igniting. In cases with severe blockage, this can cause the flame to burn backwards, and outside of the
burner tubes, which can cause damage to your grill and/or personal injury. IMMEDIATELY SHUT OFF
THE FLOW OF LP GAS AT THE CYLINDER BY TURNING THE HAND WHEEL
CLOCKWISE SHOULD THIS HAPPEN. Wait for the grill to cool, and then clean all burners.