Members Mark 8 Cube Room Organizer User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2015-11-25 Rev. 1 Factory: KONRIC (16086)
8 Cube Room Organizer
Stock # DYL8RO-R-E Rustic
Stock # HAN8RO-DO-E Dark Oak
Stock # NOA8RO-WG-E Warm Gray
ADULT ASSEMBLY REQUIRED
We would like to hear from you with any comments or suggestions. In the continental U.S. or Canada,
you can call us toll-free at 1-888-301-0332 from 8:00 a.m. to 5:00 p.m., CST, Monday – Friday. You
can also send us an email using the feedback icon at SamsClub.com.
For assembly questions, please call 1-866-942-5362 from 8:30 a.m. to 4:30 p.m., PST, Monday –
Friday
LOT NUMBER:
DATE PURCHASE
D
:
/
/

Page 2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: 8 Cube Room Organizer
MADE IN CHINA
CAM LOCK SYSTEM OPERATION
HOW THE ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the room organizer.
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE
MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY
,
CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 100 lb. (45.3 kg)
MAXIMUM LOAD 20 lb. (9 kg)
MAXIMUM LOAD 200 lb. (90.7 kg)

Page 3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top/Bottom Panel (Qty. 2) B- Side Panel (Qty. 2)
C- Large Divider Panel (Qty. 2) D- Center Divider (Qty. 1)
(With Cam lock holes)
E- Small Divider Panel (Qty. 4) F- Storage Basket (Qty. 8) G- Basket Flooring (Qty. 8)
(1) ∅5/16" x 2-1/2" Bolt (2) Cam Lock (3) Cam Bolt
(Qty. 8+1 extra) (Qty. 4+1 extra) (Qty. 4+1 extra)
(4) ∅15 x 60 mm Wood Dowel (5) ∅10 x 60 mm Wood Dowel (6) Cam Lock Cover
(Qty. 12+1 extra) (Qty. 40+2 extra) (Qty. 4+1 extra)
T-handle Allen Wrench Touch-up Pen Tipping Restraint Hardware Kit (Qty. 1)
(Qty. 1) (Qty. 1) (Inside Plastic Bag)
Tools required: Allen wrench (provided), Phillips screwdriver and rubber mallet (not provided).

Page 4
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Lay the Side Panels (B) on a level and protected surface with the pre-drilled holes facing up. Screw two
Cam Bolts (3) into the plastic bushings included on the center of each Side Panel (B). Fully tighten with
a Phillips screwdriver.
Cam Bolt
(4 used in this step)
③
B
3
B

Page 5
Assembly Instructions
3. Insert four Small Wood Dowels (5) half way into the pre-drilled holes on the Large Divider Panel (C)
by tapping lightly with a rubber mallet, if necessary. Position two Small Divider Panels (E) onto the
inserted Wood Dowels and press them together.
C
E
E
C
E5E
∅
10 x 60 mm Wood Dowel
(4 used in this step)
⑤

Page 6
Assembly Instructions
4. Attach the Center Divider (D) and one Small Divider Panel (E) to the assembled Small Divider Panel (E)
using four Small Wood Dowels (5).
5. Repeat last step to install the remaining Large Divider Panel (C) and Small Divider Panel (E) to the
previous assembly. Make certain they are located on the other end of Center Divider (D).
D
E
C
E
EC
E
EC
E
D
C/D
E5E
∅
10 x 60 mm Wood Dowel
(8 used in this step)
⑤

Page 7
Assembly Instructions
6. Insert twenty Small Wood Dowels (5) into the end holes of Large Divider Panels (C) and Center
Divider (D). DO NOT put dowels into the Cam Bolt holes.
7. Insert four Cam Locks (2) into the side holes of the Center Divider (D) making sure the arrow on the
face of Cam Lock points out and towards the entry of Cam Bolt.
8. Position the Side Panels (B) onto the inserted Small Wood Dowels (5). Press them together and secure
them in place by connecting the Cam Locks (2) (Refer to page 2 on Cam lock system operation
supplement). Once locked in place, insert the Cam Lock Covers (6) to conceal the Cam Locks.
B
B
C
E
C
E
D
C
B
5
2
6
5
3
D
B
Cam Lock Cover
(4 used in this step)
⑥
Cam Bolt
(4 used in this step)
②
∅
10 x 60 mm Wood Dowel
(20 used in this step)
⑤

Page 8
Assembly Instructions
9. Insert eight Small Wood Dowels (5) into the end holes of both Small Divider Panels (E) and insert three
Large Wood Dowels (4) into each end of the Side Panels (B).
10. Using the Wood Dowels as a guide, attach the Top and Bottom Panels (A) to both Side Panels (B) with
eight 2-1/2” Bolts (1). Tighten the bolts with the provided Allen wrench.
E
5
A
14
B
A
AB
B
E
EA
∅
5/16" x 2-1/2" Bolt
(8 used in this step)
①
∅
15 x 60 mm Wood Dowel
(12 used in this step)
④
∅
10 x 60 mm Wood Dowel
(8 used in this step)
⑤

Page 9
Assembly Instructions
11. Ask for assistance to stand the unit upright.
12. Unfold the Storage Baskets (F) and then place the Basket Flooring (G) inside the open basket to ensure
it remains square. Position the Storage Baskets onto the compartments as shown.
13. You can combine two or more units to create an attractive storage wall for your home.
FF
F
G
F

Page 10
Assembly Instructions
14. Position the assembled cabinet at the desired location against a wall.
15. Now, follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware Kit to
attach the tip-over restraints to the unit and the wall, as shown in the illustration.
NOTE: Young children can be seriously injured by tipping furniture. You must install the
Tipping Restraint Hardware with the unit to prevent the unit from tipping, causing any
accidents or damage. The tipping restraints are intended only as a deterrent, they are not a
substitute for proper adult supervision. The tipping restraints are not earthquake restraints. If
you wish to add the extra security of earthquake restraints, they must be purchased and
installed separately.