Members Mark TM013680 User manual

1
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Model Number: TM013680
THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
Teak Porch Rocker
Assembly Manual

2
Important Safety Information
Please read all instructions carefully before assembling this furniture.
For your safety, assembly by two or more adults is strongly recommended.
Use only vendor-supplied hardware to assemble this item. Using unauthorized
hardware could jeopardize the structural integrity of the item.
Hardware may loosen overtime. Periodically check that all connections are tight.
·
·
·
·
Before Assembly
Remove all parts and hardware from the box. Place all items on a carpeted or
scratch-free work surface, as this will avoid damaging parts during assembly.
The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, do not dispose of any
packaging or contents of the shipping carton until assembly is complete.
Use the parts and hardware lists below to identify and separate each of the
pieces included.
The use of power tools for assembly is not recommended. Power tools can
damage the hardware and/or split the wood.
Note: Do not fully tighten all bolts until all parts are in place. Failure to follow
these instructions may cause the bolts to misalign during assembly.
·
·
·
·
·
·
Care and Cleaning
To increase the item lifespan, avoid leaving the furniture in standing water or
indirect contact with wet ground.
·
Cover or move the furniture into covered storage during inclement weather and
during winter months.
·
Clean periodically with soft flannel cloth, slightly dampened with a mild soap
solution and warm water. DO NOT use abrasive material, bleach or scouring
products. Dry thoroughly with soft cloth.
·

3
1 1/2" Bolt
Qty: 6 Pcs + 1
Hardware
(E)
Component
A2 ........... Left side frame ......... 1 pc
B.............. Back support ............ 1 pc
C ............. Seat ........................... 1 pc
D ............. Rocker ....................... 2 pcs
A1 A2 B
C
Screw
Qty: 4 Pcs + 1
(F)
Glue
Qty: 1 Pc
(G)
Qty: 6 Pcs + 1
(H)
A1 ........... Right side frame ...... 1 pc
Rubber mallet (not included)
Need assistance? Visit us at: samsclub.com/membersmarkhelp
Tools Needed for Assembly
Wooden cap
Phillips Screwdriver (not included)

Upright the chair.
Make sure all parts are connected and tighten all bolts
completely using screwdriver. Tap in the wooden caps
(H) to cover bolts head using rubber mallet.
Invert the chair and repeat the step 2 procedure to secure
the frame.
WARNING !
- Pour a small amount of glue (G) into the holes on rockers (D).
- Attached each rocker (D) to right and left side frame (A1 &
A2) as picture shown, connecting front of rockers to front legs
first then the back of rockers. Secure connections with screws
( F ).
3
Install back support (B) and seat (C) into corresponding holes
of right side frame (A1).
Attach the left side frame (A2) onto back support (B) and seat
(C). Secure left side frame (A2) using 1 1/2" bolts (E), as
shown.
4
FRONT
12
DO NOT USE THE ROCKING CHAIR BEFORE ALL THE BOLTS ARE FULLY TIGHTENED. IF THE BOLTS ARE NOT
FULLY TIGHTENED, THE CHAIR SECTION CAN BECOME LOOSE AND MAY CAUSE THE CHAIR TO COLLAPSE
WHICH MAY RESULT TO INJURY OR DAMAGE.
E
A2
H
H
E
A1
C
B
D
A1
F
GD
Fig. 1
Fig. 2
BACK
A1
FRONT
4
FRONT
Screw
Qty: 4 Pcs
(F) Glue
Qty: 1 Pc
(G) 1 1/2" Bolt
Qty: 3 Pcs
(E)
Wooden cap
Qty: 6 Pcs
(H)
1 1/2" Bolt
Qty: 3 Pcs
(E)
Need assistance? Visit us at: samsclub.com/membersmarkhelp