Members Mark Fremont BFV01301-8PC Owner's manual

THIS ASSEMBLY MANUAL CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Assembly Instructions & User's Manual
for
Members Mark Fremont 8pc Round Dining Set
Item Number:
Model Number: BFV01301-8PC
Customer Assistance : 1-800-416-3511
or Email: [email protected]
(spare/replacement parts)
Page 1
Need Assistance? Visit us at: samsclub.com/membersmarkhelp

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 2
Table of Contents
Quality Statement.............................................................3
Important Safety Information.............................................3
Before Assembly..............................................................3
Package Contents............................................................4
Product Information..........................................................5
Care & Use and Storage Instructions.................................11
Warranty Information.......................................................11
Swivel Rocker
Components................................................................6
Hardware....................................................................6
Tools..........................................................................6
Step1.........................................................................7
Components...............................................................8
Hardware...................................................................8
Tools..........................................................................8
Step1-Step4..........................................................9-10
Table

Before Assembly
Important Safety Information
Please read all instructions carefully before assembling this furniture.
For your safety, assembly by two or more adults is strongly recommended.
Use only vendor-supplied hardware to assemble this item. Using unauthorized
hardware could jeopardize the structural integrity of the item.
Hardware may loosen overtime. Periodically check that all connections are tight.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 3
Quality Statement
Remove all parts and hardware from the box. Place all items on a carpeted or
scratch-free work surface, as this will avoid damaging parts during assembly.
The shipping box can provide an ideal work surface if none is available.
Use the components and hardware lists below to identify, inventory and
separate each of the hardware and components included.
To avoid accidentally discarding small components or hardware, do not dispose
of any packaging or contents of the shipping carton until assembly is complete.
DO NOT USE power tools unless it is explicitly identified in this manual as
required for use during assembly. Power tools can damage the fasteners,
hardware and/or components.
Do not fully tighten all fasteners / screws until all parts are in place. Failure to
follow these instructions may cause the fasteners / screws to misalign during
assembly.

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
1Set / 3Ctn
Box1of3：
Box3of3：
Component Quantity
Description
A
B
C
D
Swivel Rocker
Table Leg
6
4
Component QuantityDescription
A1
A B
Page 4
Package Contents
A
Lazy Susan
Leg Connector
Bracket 1
C
Box2of3：
Component QuantityDescription
A1
A
Table Top
D
Furniture Cover 1

Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Description Dimensions
Part No.
BFV01301 23.75" W *27.25" D *36" H 250lb N
A.Foot Cap
FC0359 N/A N/A Y
Description Dimensions
Part No.
AZT03107 YN/A
Page 5
Product information
A
Description Dimensions
Part No.
ALE15719 59.75" W *RD*29" H N
A.Foot Cap
FC0614 N/A N/A Y
Swivel Rocker
Dining Table
Lazy Susan
A
26" RD
N/A
Weight
Capacity
Factory
Assembly
Weight
Capacity
Factory
Assembly
Weight
Capacity
Factory
Assembly
Description Part No.
ZZK05512
Furniture Cover

(H1)
5/16"X35MMBOLT
Qty: 4
PART NO:HW0820
(H2)
Qty: 4
Ø8.0 X 2.3 MM SPRING WASHER
PART NO:HW0003
(H3)
Qty: 2
"U" METAL PLATE
PART NO:HW0760
(H4)
Qty:
5/16" NUT
PART NO:HW0015
4
(H5)
Qty:
ROCKER PLATE
(
G0228
FACTORY ASSEMBLY)
PART NO:
2
Components
Hardware
A.
Part No.
Qty 1
CHAIR FRAME
SR0299
Tools
Page 6
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
(H7)
HEX WRENCH-2
HW0008
Qty:
PART NO:
1
(H6)
HEX WRENCH-1
HW000
Qty:
PART NO:
1
7
B.
Part No.
Qty 1
SWIVEL BASE & ROCKER
ASSEMBLY
SR0230

"U" BAR
outer carton
(H3)
U" METAL PLATE
Qty: 2
(H7)
HEX WRENCH-2
Qty: 1
(H6)
HEX WRENCH-1
Qty: 1
(H4)
5/16" NUT
Qty: 4
(H2)
Ø8.0 X 2.3 MM SPRING WASHER
Qty: 4
(H1)
5/16"X35MMBOLT
Qty: 4
"U" BAR "U" BAR
H3
H4
H2
H1
Hand tighten only 2-3 turns.
NOTE: Bolts must be
FULLY .tightened
AB
CD
E
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 7
Step 1
H6
H7
CAUTION:
1.Note the horseshoe shape of the rocker plate. Point the open end of the horseshoe away from you. The arrows
on the rocker assembly should be pointing towards you.
2.Failure to place "U" metal plates (H3) under the rocker plates and above the "U" bar exactly as shown in
diagram will cause the bolt heads and nuts to damage the structure of the rocker plates and the "U" bar. Damage
due to over tightening of bolts or improper assembly could cause injury and may void your warranty.

Components
A.
Part No.
Qty 1
TABLE TOP
AT73163
B
Part No.
Qty 1
.LEG CONNECTOR BRACKET
AT73164
C.
Part No.
Qty 4
TABLE LEG
AT73165
Tools
(H6)
HEX BOLT DRIVER
Qty:
PART NO:HW0006
1
Page 8
D.
Part No.
Qty 1
LAZY SUSAN
AT73321
(H7)
Qty: 1
HEX WRENCH
HW0009
PART NO:
(H1)
1/4"X40MMBOLT
Qty:
PART NO:HW0812
4
(H3)
Ø18 X Ø6.5 X 1.5 MM WASHER
103
Qty: 4
PART NO:HW0
(H2)
Qty: 8
Ø6.5 X 1.0 MM WASHER
PART NO:HW0004
(H5)
Qty:
(FACTORY ASSEMBLY)
UMBRELLA HOLE RING (SET)
PART NO:G0288
1
(H4)
Qty:
1/4" NUT
PART NO:HW0014
8
Hardware
Need Assistance? Visit us at: samsclub.com/membersmarkhelp

outer carton
(H3)
Qty:
Ø18 X Ø6.5 X 1.5 MM WASHER
4
Hand tighten only 2-3 turns.
(H2)
Qty: 8
Ø6.5 X 1.0 MM WASHER
(H4)
Qty: 8
1/4" NUT
Hand tighten only 2-3 turns.
H3
H1
H2
H4
Step 1
Step 2
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Step1-Step4
Page 9
(H1)
1/4"X40MMBOLT
Qty: 4

Step 3
Step 4
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Page 10
4x
(H6)
Qty: 1
HEX BOLT DRIVER
(H7)
Qty: 1
HEX WRENCH
NOTE: Bolts must be
FULLY tightened.
4x
H6
H7
4x

CARE AND MAINTENANCE
FRAMES
FABRICS
STRAPS
UMBRELLA USAGE WARNING!
Cleaning
Maintenance
Cleaning -
Maintenance -
- Use mild soap and warm water. Do not use abrasive materials, cleansers or bleach
products. Rinse with clean water and dry thoroughly.
- Periodically clean and dry thoroughly. Be sure to drain any water accumulated
inside the frames. To thoroughly drain frames, remove foot caps and tilt the frames, if necessary, to
remove all water. This is critical. Water allowed to accumulate inside the frames and then
exposed to sub-freezing temperatures can cause damage to the frame tubing. Always clean, drain
and dry thoroughly before storing for the winter. For best results, always store or cover your
furniture when not in use. We recommend commercially available outdoor furniture covers. Any
small nicks or scratches can be covered with a light application of touch-up paint.
** When cleaning or moving large or heavy items, always have two people work together. Never
drag furniture.
Furniture covers are a great way to protect your set from harsh elements of weather and UV light.
However, it is important to ensure furniture and covers are free of moisture and debris before
covering. It is also necessary to promptly uncover furniture after rain and during periods of high
humidity to prevent moisture build up. Failure to do so can lead to permanent surface and finish
damage.
Wash frequently with mild soap, warm water and a soft cloth. Rinse thoroughly with
warm, clean water. Do not use abrasive materials, cleansers or bleach products.
Periodic application of commercially available vinyl cleaners and vinyl protectors will
enhance the look and prolong the life of straps. If your strap chair has cushions, make sure any
vinyl protectors applied are completely dry before placing cushion back on the chair.
If you will be using an umbrella with your table, make sure the plastic umbrella ring is inserted into
the hole in the center of the table. Place the umbrella through the opening and into an umbrella
stand made of cast iron, wrought iron, steel plate or blow molded plastic filled with 20-50 lbs or 9-
22 kgs of sand and water. If your table is 72" or 182 cm or larger, we recommend a weight of at
least 50 lbs or 22 kgs or more. NEVER USE AN UMBRELLA WITH A TABLE WITHOUT USING
AN UMBRELLA BASE AND RING AS DESCRIBED ABOVE. ALWAYS REMOVE YOUR
UMBRELLA FROM THE TABLE WHEN NOT IN USE. NEVER USE AN UMBRELLA DURING
STORMS OR WINDY CONDITIONS.
Need Assistance? Visit us at: samsclub.com/membersmarkhelp
Care & Use Instructions
Warranty Information
This product component has a 5 year guarantee against defects in material and/or workmanship. If
you have any questions regarding the warranty or spare / replacement parts, please call our toll-
free number 1-800-416-3511 or email us at [email protected]
NOTE: Please consider recycling all applicable packaging material.
Page 11

Distributed by Sam's West Inc.
2101 SE Simple Savings Dr.
Bentonville, Arkansas 72716-0745
Made in China
Page 12
Need Assistance? Visit us at: samsclub.com/membersmarkhelp