Memphis PRO CART ITC 3 User manual

CONTENTS
1: Tools Required
2: Included Hardware
2-3: Assembly Instructions
4: Wi-Fi Setup and App Pairing
TIME REQUIRED
1.5 Hours
PRO CART ITC 3 QUICKSTART GUIDE
Revision: B0VG0895
TOOLS REQUIRED
 3/8” Open End
Wrench, Socket or
Adjustable Wrench
 Phillips Screw Driver
or Drill
 Snips or Heavy Duty
Scissors
 Cut Resistant Gloves
 5mm Allen Wrench
MEMPHIS WI-FI SETUP GUIDE
ON YOUR MEMPHIS GRILL:
1. Register your account in the Memphis 3 app before
proceeding.
2. Navigate to the Settings Screen (far right icon) on the
Memphis Grill.
3. Press “WiFi” to navigate to the Connection Screen.
4. Press “Connect WiFi” to start WiFi setup. The screen will
display “Visible on Bluetooth” to show it has started.
ON YOUR PHONE OR TABLET: (In Memphis 3 App)
6. Log into Memphis 3 App using your account email and password.
7. If this is your first time setting up a grill on the app, a window will
pop up asking to “Provision Grill” or “Add Existing”. Press “Provision
Grill”.
7a. If this isn’t the first grill being added to your account, select
the settings gear in the top right corner and press “Add Grill” to
get the popup.
8. Select your home WiFi network from the scan list shown, enter the
WiFi password, and press “Provision”.
8a. The WiFi network must be a 2.4 GHz network to appear on
the list
9. Enter the Bluetooth Pin to complete provisioning.
10. Once the connection is complete the Memphis Grill will display
“Connection Successful” and update in WiFi screen information.
The WiFi connection bars will also be displayed in the top right
corner.
11. After the WiFi is connected, a popup window will appear in the
Memphis 3 app asking for the MAC address and Grill Name. This
information can be found on the WiFi screen of the Memphis Grill.
Press Settings Menu (Bottom right icon) -> WiFi-> WiFi screen.
*Contact Memphis Technical Support if unable to connect.
34
7
8
7a
11

MEMPHIS PRO CART ASSEMBLY INSTRUCTIONS
1: Remove both shelves, the hardware kit, Savorizer, and grate
kit from the grill. The shelves are located in boxes underneath
the grill. The Savorizer and grate kit are in the grill hood. To
remove the Savorizer, cut the 4 zip ties holding it in place.
Remove all laser film on the grill. This is a peel-able plastic left
on to protect your grill from scratches during manufacturing and
transit. Remove all laser film and laser etch lines with WD40 or
olive oil. Once a grill has been heated up it is very difficult to
remove this film, be sure to check your grill thoroughly before
first burn.
2: Replace the Savorizer and place 3 large grates on the lower
level and the long grate on the upper level.
3: Remove the Direct Flame Insert and Genie Tool from the right
side shelf.
4: Install 2 shelf bolt (#5) into the right side of the grill. Leave
approximately 1/4” of the bolts sticking out so that the shelf can
slide onto them.
NOTE: ALWAYS HOLD SHELVES FROM THE BOTTOM AS THE
SHELF TOP SLIDES OPEN!
5: Slide the shelf onto the bolts, press down on the shelf to
secure into the keyway. Install the remaining 3 shelf bolts.
Tighten bolts using 3/8” wrench, socket, or adjustable wrench.
6: Repeat steps 5 and 6 for the left side of the grill.
7: Remove two 5mm socket head screws from Display Housing
shipping bracket using the 5mm allen wrench.
8: Snip the zip tie that secures the Display Housing to the
shipping bracket.
9: Mount the Display Housing perpendicular to the side panel
over the Display Insert bracket using the two 5mm x 50mm
socket head screws in the hardware kit.
10: Attach the included antenna to the grill by twisting in a
clockwise motion. The antenna will be included in the hardware
kit located in the grease tray.
11: Attach the cord wrap with included screws found in the
hardware kit.
COMPLETE THE STEPS BELOW IN NUMERICAL ORDER, REFERENCE THE SAME
NUMBERED DIAGRAM AND HARDWARE COMPONENTS FOR CLARIFICATION.
10
HARDWARE COMPONENTS
9. Meat Probe
VG0956 1
8. Cord Wrap
VG0560 1
7. #10 Screw
(SS) DS2186 2
5. Shelf Bolt
DS2311 10
2. Savorizer
VG4403 1
4. Genie Tool
VG1595 1
3. Direct Flame
Insert VG4407 1
Description/ Part No. Qty: Picture:
8
7
11
5
4
2
9
1. VG0001Grate
Kit 1
Right Shelf
Left Shelf
Hardware Kit
Packaging Locations
Savorizer
6. Antenna
VG9023 1