Memphis Elite Built-In ITC 3 User manual

CONTENTS
1: Tools Required
2: Included Hardware
2-3: Assembly Instructions
4: Wi-Fi Setup and App Pairing
TIME REQUIRED
1.5 Hours
MEMPHIS WI-FI SET UP GUIDE
ELITE CART ITC 3 QUICKSTART GUIDE
Revision: A0VG0896
TOOLS REQUIRED
 3/8” Open End
Wrench, Socket or
Adjustable Wrench
 Phillips Screw Driver
or Drill
 Snips or Heavy Duty
Scissors
 Cut Resistant Gloves
 5mm Allen Wrench
ON YOUR GRILL CONTROLLER:
1. Navigate to the Settings Screen on the display.
2. Select “Connect to Wifi” to navigate to the
Connection Screen.
3. Press the blue “Connect Wifi” button to broadcast
the BLE signal.
4. Follow the steps below on your Memphis 3 App.
ON YOUR PHONE OR TABLET: (In Memphis 3 App)
5. Log into Memphis 3 App using your account email and
password.
6. Navigate to the Setting Screen and select “Add Grill”.
7. Once the grill has been detected, the available
Networks will be displayed in a list.
8. Select the 2.4GHz network you would like to connect
to your Memphis grill, enter the network password, and
press “Provision”.
9. If successful, the controller will display “Connection
Sucsessful” and show the WiFi signal strength in the
top right corner.
*Note: If a red X is displayed on the controller instead of
the signal strength the connection was unsuccessful.
Attempt to provision the controller again, otherwise contact
Memphis Technical Support.
Navigating back to the “Connect to Wifi” Screen displays
the Network name, signal strength, and connection status
as well the Grill Name, MAC Address, and IP Address of
your Memphis Grill.
GRILL NETWORK INFORMATION

MEMPHIS ELITE CART ASSEMBLY INSTRUCTIONS
1: Remove both shelves, the hardware kit, Savorizer, and grate
kit from the grill. The shelves are located in boxes underneath
the grill. The Savorizer and grate kit are in the grill hood. To
remove the Savorizer, cut the 4 zip ties holding it in place.
Remove all laser film on the grill. This is a peel-able plastic left
on to protect your grill from scratches during manufacturing and
transit. Remove all laser film and laser etch lines with WD40 or
olive oil. Once a grill has been heated up it is very difficult to
remove this film, be sure to check your grill thoroughly before
first burn.
2: Replace the Savorizer and place 3 large grates on the lower
level and the long grate on the upper level.
3: Remove the Direct Flame Insert and Genie Tool from the right
side shelf.
4: Install 2 shelf bolt (#5) into the right side of the grill. Leave
approximately 1/4” of the bolts sticking out so that the shelf can
slide onto them.
NOTE: ALWAYS HOLD SHELVES FROM THE BOTTOM AS THE
SHELF TOP SLIDES OPEN!
5: Slide the shelf onto the bolts, press down on the shelf to
secure into the keyway. Install the remaining 3 shelf bolts.
Tighten bolts using 3/8” wrench, socket, or adjustable wrench.
6: Repeat steps 5 and 6 for the left side of the grill.
7: Remove two 5mm socket head screws from Display Housing
shipping bracket using the 5mm allen wrench.
8: Snip the zip tie that secures the Display Housing to the
shipping bracket.
9: Mount the Display Housing perpendicular to the side panel
over the Display Insert bracket using the two 5mm x 40mm
socket head screws in the hardware kit.
10: Attach the included antenna to the grill by twisting in a
clockwise motion. The antenna will be included in the hardware
kit located in the grease tray.
11: Attach the cord wrap with included screws found in the
hardware kit.
COMPLETE THE STEPS BELOW IN NUMERICAL ORDER, REFERENCE THE SAME
NUMBERED DIAGRAM AND HARDWARE COMPONENTS FOR CLARIFICATION.
10
HARDWARE COMPONENTS
Left and
Right Shelves
Hardware Kit
Packaging Locations
Savorizer
Grates
1
9. Meat Probe
VG0956 1
8. Cord Wrap
VG0560 1
7. #10 Screw
(SS) DS2186 2
5. Shelf Bolt
DS2311 10
4. Genie Tool
VG1595 1
3. Direct Flame
Insert VG4407 1
2. Savorizer
VGE4403 1
1. VG0002 Grate
Kit 1
Description/ Part No. Qty: Picture:
8
7
11
5
4
2
9
6. Antenna
VG9023 1