Mercia Garden Products 01DTOVAX0806DDFW-V1 User manual







 

 
















  



2mm Drill bit
x2 





























































 
















































¡





 
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Overall Dimensions:
Width = 1905mm
Depth = 2428mm
Height = 1986mm
Base Dimensions:
Width = 2350mm
Depth = 1753mm
01DTOVAX0806DDFW-V1
01DTOVAX0806DDNW-V1
Building Content:
Door Gable QTY 1
AI-01R11OVAGSD1707X1961-V1
Back Gable QTY 1
AI-01R11OVAGP1707X1961-V1
Plain Panel QTY 2
(QTY 4 WINDOWLESS ONLY)
AI-R11OVPP1180X1567-V1
Window Panel QTY 2
(WITH WINDOW ONLY)
AI-01R11OV2CW1180X1567-V1
1 2 3 4
Floor QTY 2
AI-R11OSBF1175X1753-V1
Roof Sheet QTY 4
PI-03-0386
(1195MM X 1039MM)
5 6 7
Door QTY 2
AI-R11FBMBZBD437X1660-V1
10
11
12
13
14
Fascia 7x60x1016mm QTY 4
OVLPR60-1016mm
Fixed Window Strip 12x30x546mm QTY 14 (WITH WINDOW ONLY)
S1230-546mm
Cover Trims 12x45x1575mm QTY 6
S1245-1575mm
Ridge Bar 27x70x1152mm QTY 2
F2770-1152mm
Finial QTY 2
SHED DIAMOND FINIAL
8
9
19
18
17
Door Beading Strip 7x28x1590mm QTY 2
OVLPR28-1590mm
T Hinge QTY 4
PI-02-1043
Plastic Window Cill QTY 2
(WITH WINDOW ONLY)
PI-08-0013
Styrene QTY 4
(WITH WINDOW ONLY)
PI-05-0114
20
22
23
24
25
26
27
28
L-Bracket QTY 2
PI-07-0012
16
Turn Button QTY 2
PI-07-0034
21
15
Eaves Frame 28x28x1195mm QTY 4
F2828-1195mm
U Channel
PI-07-0013
Truss Frame - 27x44x931mm QTY 2
F2744-G-971mm
Truss Support Brace - 27x44x450mm QTY 1
F2744-G-490mm
Truss Block - 27x44x140mm QTY 2
F2744-G-160mm
Door Strip - 12x60x770mm QTY 2
S1260-770mm
Door Block - 28x28x150mm QTY 2
F2828-150mm
Felt
Capping Felt Hasp and Staple QTY 1
PI-07-0207

¡
 
Nail Bag
There may be extra screws present in the nail bag
Felt Tacks x 100
30mm Screw x 153
50mm Screw x 50
40mm Screw x 64
20mm Screw x 6
Pre Assembly
Before assembling remove the transportation
blocks from the bottom of each panel.
Take care removing the blocks as to not damage
the panels. Tap with a at headed screwdriver
and hammer.
Dispose of the blocks once removed.
Step 1
Parts needed - No. 1 QTY 1
No. 7 QTY 2
No. 20 QTY 4
Place the doors (No. 7) within the door
gable opening. Fix the T Hinges (No.20)
onto the door and Door Gable as shown.
Ensure that the screws go through the
cladding and into the framing behind.
28x30mm screws
30mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
20
1
7
The correct positioning of the Double Doors
**PLEASE NOTE** Before tting the
hinges, ensure the inner door framing
is the correct way round as shown in
the illustration below.


 
5
5
40mm
screw
Pre drill
hole
55
IMPORTANT: Pre-drill before xing screws.
Step 2
Parts needed - No. 5 QTY 2
Place the oors (No.5) on a rm and level base,
ensure the base has suitable drainage free from areas
where standing water can collect.
See the front page for base requirements.
Attach the oors together using 12x40mm screws.
12x40mm Screws
Step 3
Parts needed - No. 2 QTY 1
No. 3, (or 4) QTY 1
**Please note: Whether you have pur-
chased the with windows building or no
windows building, the panels are inter-
changeable. Decide which works best
before assembly.**
Fix the corners of the Back Gable (No.2)
and the Plain Panel (No.3) (or Window
Panel) with 3x50mm screws as shown in
the illustration.
Do not secure the building to the oor
until the roof is tted.
Position the panels so there is equal spac-
ing between the oor and cladding on all
sides.
3x50mm Screws
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
3
2


 
Step 4
Parts needed - No. 3, (or 4) QTY 1
No. 4, (or 3) QTY 1
Fix the corners of the Back Gable
(No.2) and the Window Panel (No.4)
(or Plain Panel) with 3x50mm screws as
shown in the illustration.
Fix the ends of the Plain Panel (No.3)
(or Window Panel) to the already
standing Plain Panel (No.3) (or
Window
Panel) with 3x50mm screws as shown
in the illustration.
Do not secure the building to the oor
until the roof is tted.
Position the panels so there is equal
spacing between the oor and clad-
ding on all sides.
6x50mm Screws
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
3
3
2
side
Use for no
window buildings
3
4
Use for no
window buildings
3
Step 5
Parts needed - No. 1 QTY 1
No. 4, (or 3)
QTY 1
Fix the end of the Window Panel
(No.4) (or Plain Panel) to the
already standing panel with
3x50mm screws as shown in the
illustration.
Fix the corners of the Door Gable
(No.1) to the ends of the Side
Panels with 6x50mm screws as
shown in the illustration.
Do not secure the building to the
oor until the roof is tted.
Position the panels so there is
equal spacing between the oor
and cladding on all sides.
9x50mm Screws
1
4
Pre drill
hole
50mm
screw
IMPORTANT: Pre-drill before xing screws.
Step 6
Parts needed - No. 12 QTY 2
No. 26 QTY 2
No. 28 QTY 1
Connect the Ridge Bars (No. 12) together
with the metal U-Channel (No. 28), using
10x30mm screws.
Attach the L-Brackets (No. 26) to each end
of the Ridge Bars (No. 12) with 2x30mm
screws per L-Bracket.
*Ensure the L-Brackets are ush with the
ends of the ridge bars.
14x30mm Screws
Pre drill
hole
30mm
screw
28
26
26
12
12
IMPORTANT: Pre-drill before xing screws.


 
Step 7
Place the assembled ridge bar in between
the Gables (No. 1&2) in line with the central
uprights within the gables.
If you have not yet assembled your ridge bar
please refer to step 6.
Secure the ridge bar (No. 12) to the central
uprights with 2x30mm screws per L-Brackets
(No. 26), as shown in the illustration.
4x30mm Screws
30mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
26
12
6
6
12
12
12
6
6
13
30mm
screw
40mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
Step 8
Parts needed - No. 6 QTY 4
No. 13 QTY 4
Fix the eaves frames (No.13)to each roof sheet
(No.6) using 3x30mm screws per eave.
12x30mm Screws
Place the Roof Sheets (No. 6) on top of the building
making sure the roof sheet meets the pointed edge
of the Gables (No. 1&2) and it sits well on the top
of the Ridge Bar (No. 12).
**The edges of the roof sheets must be ush
with the outer cladding of the Gables (No.
1&2).**
From the top, x directly through the roof sheets
(No. 6) and into the ridge bar (No. 12) below using
3x40mm screws per roof sheet.
It is essential that the ridge bar (No. 12) and the
roof sheet (No. 6) pull together when xed with
50mm screws. You may require another person
pushing the ridge bar (No. 12) up from below to
achieve this.
12x40mm Screws


 
30mm
screw
Pre drill
hole
Step 9
Parts needed - No. 14 QTY 2
Position a Truss Frame (No. 14), centrally
underneath the join of the two roof
sheets (No. 6) internally. Ensure the Truss
Frame (No. 14) sits ush to the underside
of the roof sheets and ush at the top as
shown in the illustration.
Fix the Truss Frame (No. 14) in place
using 30mm screws xing through the
roof sheet (No. 6) into the Truss Frame
(No. 14) from the outside of the building.
*Alternate screwing through each roof
sheet for a more secure hold.
8x30mm Screws
14
14
14 14
IMPORTANT: Pre-drill before xing screws. Step 10
Parts needed - No. 16 QTY 2
Place Truss Block (No. 16) directly below
the Truss Frame (No. 14). Fix the Truss
Block to the framing within where the
side panels meet in the centre. Fix in
place with 2x50mm screws.
Repeat the above two actions on either
side of the building.
4x50mm Screws
Pre drill
hole
50mm
screw
16
16
16
16
IMPORTANT: Pre-drill before xing screws.

¢
 
15
Step 11
Parts needed - No. 15 QTY 1
Place the Truss Support Brace (No. 15)
underneath the two Truss Frames (No.
14) ensuring they sit ush to one another.
The Truss Support Brace (No. 15) should
sit horizontal - parallel to the oor.
Once in position x the Truss Support
Brace (No. 15) in place with 2x40mm
screws at each end of the brace.
4x40mm Screws
40mm
screw
Pre drill
hole
15
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
40mm
screw
Step 12
Use 40mm screws to x the roof sheets
(No. 6) down the sides and at the
bottom being sure that the screws attach
into the framing below.
20x40mm Screws
IMPORTANT: Pre-drill before xing screws.
Step 13
Once the roof is xed,
attach the building to the oor
with 50mm screws.
Ensure the screws go through
the panel into the oor faming.
28x50mm Screws
b
50mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
side


 
Step 14
Parts needed - No. 23 QTY 1
No. 24 QTY 1
Cut the felt (No. 23) into two sheets at
2500mm and cut a sheet from the
capping felt (No. 24) at 2500mm. Lay
onto roof as shown in diagram ensur-
ing there is a 50mm overhang around
the sides.
Apply the felt tacks with a 100mm
space per tack..
100x Felt Tacks
HANDLE
WITH CARE
2
3
4
Felt
tacks
23 23
24
23
23
24
Step 15
For a windowless version go to step 16
Parts needed - No. 9 QTY 14
No. 21 QTY 2
No. 25 QTY 2
Pre drill
hole
30mm
screw
9
9
9
9
21
a
b
c
d
SILICONE
SEALANT
9
9
9
Styrene
Window Cill
Cladding
Side View
25
25
a
b
c
d
IMPORTANT: Pre-drill before xing screws.
Fix 4x Window Strip (No. 9) to the sides
of the framing exposed in the window gap of
the Window Panel (No. 2) using 3x30mm
screws per Strip .
Place the Plastic Window Cill (No.21) into the
window panel (No.1) opening as shown in
the illustration. Fix screws through the cill for
extra support using 3x30mm screws.
Fit the styrene sheets (No. 25) on top of the
Plastic Window Cill (No. 21).
*For added weather protection t your
windows using silicone sealant around
the outside edges.
**When positioning the styrene sheets ensure
there is an equal distance on all sides.
Attach a further 3x window strips (No. 9)
to either side of the windows and the centres.
Secure into place using 3x30mm screws per strip.
Repeat this process for the other window panel.
48x30mm Screws