Mercia Garden Products 0619LOG015-V5 User manual

P 1
0619LOG015-V5
0619LOG015-V5 : 19mm log cabin 4x3m (T&G roof)
2mm Drill bit
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All buildings should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
Please retain product label and instructions for future reference
General Instructions
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
BUILDING A BASE
When thinking about where the building and base are going to be constructed:
Ensure that there will be access (60cm) to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions. The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for your specic product code
For ease of assembly use a
rubber mallet to t the log
boards. Do NOT use a heavy
hammer.
Ensure to measure and check before cutting
boards.
It is advisable to use a hand
saw when cutting roof and
oor boards.
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
To ensure log boards are even, use a spirit
level to check each layer has been installed
correctly.
Measure
under the
head
Measure
overall
length
Screws & Nails Bolts To identify the
xings required
for each step use a
measuring tape.

3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
P 2
0619LOG015-V5
Overall Dimensions:
Width = 4028mm
Depth = 3163mm
Height = 2598mm
Base Dimensions:
Width = 3808mm
Depth = 2804mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Gable 2996mm
QTY 2
Starter Board - 66x19x4000mm QTY 2
LB19RT66-A-4000
Log Board - 120x19x1216mm QTY 12
LB19-B-1216
Log Board - 120x19x232mm QTY 24
LB19-B-232
Log Board - 120x19x232mm QTY 24
LB19-C-232
Log Board - 120x19x4000mm
LB19-AD-4000
Log Board - 50x19x4000mm QTY 2
LB19RG50-A-4000
Log Board - 120x19x2996mm QTY 25
LB19-A-2996
Log Board - 120x19x1123mm QTY 24
LB19-B-1123
Roof Purlin - 40x90x4004mm QTY 3
F4090-A-4004
Bearer - 44x44x3720mm QTY 10
F4444-3720-PT
Bearer - 44x44x2804mm QTY 2
F4444-2804-PT
Fascia - 12x120x1630mm QTY 4
S12120-G-1630 (1x14° Cut)
Fascia - 12x120x4004mm QTY 2
S12120-4004
Eaves Frame - 27x44x4004mm QTY 2
F2744-4004
Roof Board - 12x121x1600mm QTY 74
MB12-1600
Floor Board - 12x121x2760mm QTY 35
MB12- 2760
Storm Brace - 27x44x2000mm QTY 8
F2744-2000
22
21
Short Window Pack*
QTY 3
Double Door Pack*
23
Log Board - 120x19x2996mm
LB19-AD-2996
Log Board - 120x19x4000mm QTY 19
LB19-A-4000
*All components for the Windows and Doors are
shown in the Windows and Doors instruction packs.
Closure Trim - 16x28x2400mm (approx length) QTY 14
S1628-2400

P 3
Please retain product label and instructions for future reference
Felt
24
Roof Spacers QTY 5
PI-07-0208 (20x100x2mm)
25
Felt Tacks x400
70mm Screw x64
Nail Bag
40mm Screw x506
30mm Screw x102
60mm Bolt Set x16
Pre-assembly
*Please note:
Each board interlocks at
either end in a staggered pattern.
Before securing ensure that the boards
are tted properly in their respective
tongues and grooves.
There may be extra screws present in the nail bag

Pre drill
hole
P 4
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Please retain product label and instructions for future reference
70mm
screw
14 15
14
15
10
10
4
4
Step 2
Parts Needed - No. 4 QTY 2
No. 10 QTY 2
Place the starter boards (No. 4)
on to assembled base frame
along the longest sides.
*Ensure the notches at either
end of each board are ush
and level with the ends of the
frame.
Fix each of the starter boards to
the frame by screwing through
the notch into the frame as
shown in the illustration.
Once in position place the next
log board (No. 10) onto the
assembly.
4x70mm Screws
14
14
14
14
14
14
14
14
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
70mm
screw
a
Step 1
Parts Needed - No. 14 QTY 10
No. 15 QTY 2
Lay the bearers (No’s. 14 &
15) onto a rm and level surface
(free from areas where standing
water can collect) as shown in
the illustration.
Fix the framing together at each
corner using 8x70mm screws,
ensuring the frame is ush.
8x70mm Screws
Pre drill
hole
70mm
screw
b
Following the same
method arrange the
remaining framing (No. 14)
inside the assembled frame.
*Ensure there is an equal
amount of space between
each frame.
Secure each of the frames in
place using 2x70mm screws
for each side of the bearer,
ensuring the framing remains
level.
32x70mm Screws
a
b
14
15
14
4
IMPORTANT: Pre-drill before xing screws.

Step 3
Parts Needed - No. 5 QTY 12
No. 8 QTY 6
No. 10 QTY 10
Following the same method
outlined in Pre-Assembly, lay
the rst 6 boards (No’s. 5, 8 &
10) onto the starter boards to
create your rst level.
*Ensure that the boards are
level and ush with each
other as you lay each one.
P 5
Please retain product label and instructions for future reference
10
10
8
5
5
10
8
11
6
7
6
7
Step 5
Parts Needed - No. 6 QTY 12
No. 7 QTY 12
No. 8 QTY 6
No. 10 QTY 6
No. 11 QTY 12
Following the same method
outlined in Pre-Assembly , lay
the next 6 boards (No’s. 6, 7,
8, 10 & 11) onto the assembly
to create your second
level.
*Ensure that the boards are
level and ush with each
other as you lay each one.
*Doors can be hung once the
boarding has enclosed the
door frame by 12-13 boards,
refer to door installation
instructions, if not, you can
install the door at step 7.
Step 4
Once you have laid 6 log boards (o
of the starter) up the door section,
slide the assembled door frame (No.
2) over the boards resting the frame
on top of the starter board.
Please refer to your window and
door instructions for assembly.
*Please note: This image is for illustra-
tive purposes and may dier from your
choice in product (regarding door
position). Nevertheless the process of
tting the door frame is the same.
**Please Note: The short boards at the
front of the building (either side of the
door and window opening’s) can be
placed either side depending on your
needs.
11

P 6
Please retain product label and instructions for future reference
8
23
Step 9
Parts Needed - No. 3 QTY 2
Place the gable tops (No. 3)
onto the assembly. Fix into
position by screwing through
the notches as shown in the
illustration.
*Ensure that the boards are
level and ush with each
other as you lay each one.
4x70mm Screws
Pre drill
hole
70mm
screw
10
8
11
6
7
7
6
11
3
3
Step 7
Parts Needed - No. 6 QTY 12
No. 7 QTY 12
No. 8 QTY 6
No. 10 QTY 6
No. 11 QTY 12
Following the same method
outlined in Pre-Assembly , lay
the remaining boards (No’s. 6, 7,
8, 10 & 11) onto the assembly
to bring the board level to the
top of the window and door
frames.
*Ensure that the boards are
level and ush with each
other as you lay each one.
*Doors can be hung once the
boarding has enclosed the door
frame.
Step 8
Parts Needed - No. 8 QTY 1
No. 10 QTY 1
No. 22 QTY 1
No. 23 QTY 1
Following the same method
outlined in Pre-Assembly , lay
the last two boards (No’s. 10
& 22)onto the window and
plain side.
Once in position place log
boards (No’s. 8 & 23) onto
the front and rear of the
assembly.
*Ensure that the boards are
level and ush with each
other as you lay each one.
10
22
Step 6
Once you have laid the second
level of boards onto the assembly
slide the window(s) (No. 1)
between the smaller boards and
rest on to the longer board.
Please refer to your window and
door instructions for assembly.
*Ensure the boards are level with
each end.
*Please note: This image is for
illustrative purposes and may
dier from your choice in product
(regarding window position).
Nevertheless the process of tting
the window is the same.

P 7
Please retain product label and instructions for future reference
Step 10
Parts Needed - No. 9 QTY 2
Following the same method
outlined in Pre-Assembly, lay
log board (No. 9) onto
the front and rear of the
building.
Fix with 2x70mm screws per
board, 1 at either end.
4x70mm Screws
9
9
Pre drill
hole
70mm
screw
Pre drill
hole
70mm
screw
13
13
13
a
b
Step 11
Parts needed - No. 13 QTY 3
Align the Roof Purlin(s) (No.
13) into the cut out slots on each
gable top ensuring each roof purlin
interlocks the boards.
Secure the roof purlins at
each end by screwing through the
bars into the boards (ensure to
pre-drill to avoid the boards split-
ting) using 4x70mm screws per roof
purlins.
*Please note:The gable shown is for
illustrative purposes and may dier
in width from your choice in prod -
uct.
Nevertheless, despite any dierenc -
es
the process of xing the roof purlins
is the same.
a
b
IMPORTANT: Pre-drill before xing screws.

P 8
Please retain product label and instructions for future reference
Step 12
Parts Needed - No. 19 QTY 72
Place the rst two roof boards
(No. 19) onto the assembly on
each side, making sure the boards
are ush to the end of the roof
purlin.
Use the spacer (No. 25) to create an
expansion gap between each roof board
if installing during low levels of
moisture (Summer.) This creates an
expansion gap for the boards to
move into during high levels of
moisture (Winter.)
Once in position x to each
purlin using 3x40mm screws.
You have been issued with 74 roof
boards, but in reality you may only
need to use 72.
*Ensure the roof boards meet
at the top of the apex and leave
an overhang at the bottom.
Continue adding the roof boards
along the roof, xing each one into
position using 3x40mm screws,
making sure that each board is
interlocked, ush at the bottom &
meet at the top of the apex.
The last board on each side will
overhang: Using a straight edge
and a pencil mark out a line as
a guide.
Cut along the pencil mark and
remove the excess. Place the
cut down boards back onto the
roof and secure into place
using 3x40mm screws per
board.
*Please Note: This image is for illustrative
purposes and may dier from your choice in
product. Nevertheless the process of cutting
and tting the last roof boards is the same.
216 x40mm Screws
40mm
screw
Pre drill
hole
*Cut to t
19
19
19
18
Step 13
Parts Needed - No. 18 QTY 2
Ensuring the roof boards are ush
at the overhanging side and meet
at the apex, x the eaves frames
(No. 18) to the underside of the roof
boards using 9x40mm screws as
shown in the illustration
*Please Note: This image is for
illustrative purposes and may
dier from your choice in
product. Nevertheless the process
of xing the eaves frames is the
same.
18x30mm Screws
30mm
screw
Pre drill
hole

P 9
Please retain product label and instructions for future reference
20
20
Step 14
Parts Needed - No. 20 QTY 34
Place the rst oor board (No. 20)
inside the building ush to the log
board on one side. Continue adding
the oor boards (internally) making
sure to interlock each individual
board.
You have been issued with 35 oor
boards, but in reality you may only
need to use 34.
*Do NOT secure the boards until
the last board has been measured
and cut.
Following the same method outlined
previously measure the gap between
the bottom of the tongue (on the last
board placed) and the log board.
Using a straight edge mark out the
measurement onto the last oor
board (No. 20) and cut along the
length removing the excess.
**Please note: Mark the nal board
2mm under the measurement; This
will allow the timber to expand and
contract correctly.
Once all the oor boards are in
position secure each board into
position using 8x40mm screws.
***Please Note: Ensure to screw
through each of the oor boards
into the oor bearers.
272x40mm Screws
40mm
screw
Pre drill
hole
*Cut to t
Closure Trim
Internal
23
*Measure and cut the
closure trims to
t the internal space.
23
23
Closure Trim
Internal
12
*Measure and cut the
closure trims to
t the internal space.
12
12
Pre drill
hole
30mm
screw
*trim to t
Step 15
Parts needed - No. 12 QTY 7
Inside the building place the closure
trim (No. 12) against the boarding
and align with the roof as shown in
the illustration.
Once in position x each trim
into place by pre drilling a pilot hole
and using 6x30mm screws per trim,
equally spacing them along the face
of the board.
42x30mm Screws
30mm
screw
Pre drill
hole
*Cut to t
Step 16
Parts needed - No. 12 QTY 7
Once the oor has been laid arrange the
closure trim (No. 12)around the outside
edge of oor (internally), measure and cut
down accordingly to best match the
internal space.
Secure each trim section into place using
6x30mm spaced equally along the board
as shown in the illustration.
*Do NOT x the closure trim to the oor
boards.
42x30mm Screws
RoofRoof

P 10
Please retain product label and instructions for future reference
HANDLE
WITH CARE
12
3
4
Felt
tacks
Step 17
Parts needed - No. 24
Cut the felt into four strips and lay
onto the roof in the order shown
in the illustration.
*Ensure there is approximately 50mm
of overhanging felt each side.
Once the felt is laid out x to the
roof using felt tacks at 100mm
intervals.
*Felt size: 4124mm
252x Felt Tacks
1. 2.
3.
4.
Step 18
Parts Needed - No. 16 QTY 4
No. 17 QTY 2
Align the fascias (No’s. 16
& 17) with the roof and x
into place using 3x40mm
screws per fascia, making sure
to screw through the
fascia into the roof purlins
and eaves frame.
*Ensure the angled cuts meet
at the top of the apex.
18x40mm Screws
Pre drill
hole
40mm
screw
16
16
16
16
17
17
17