Mercia Garden Products 01OVLPA0304SDNW-V1 Instruction manual

P 1
01OVLPA0304SDNW-V1
3x4 Overlap Apex Shed
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
Please retain product label and instructions for future reference
General Instructions
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for you specic product code

2
13456
13 14
15
Pre Assembly
Remove the transportation blocks from the
bottom of each panel before beginning
assembly.
30mm
screw
Pre drill
hole
50mm Screw x24
Felt Tacks x34
20mm Screw x6
30mm Screw x74
30mm Black Screw x2
P 2
01OVLPA0304SDNW-V1
Overall Dimensions:
Length = 859mm
Width = 1313mm
Height = 1856mm
Base Dimensions:
Length = 795mm
Width = 1180mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Door Gable
AI-01OVLPDG1832X1130-V1
Plain Side QTY 2
AI-01OVLPPS800X1567-V1
Plain Gable
AI-01OVLPPG1832X1130-V1
Floor
AI-01OSBF795X1180-V1
Roof QTY 2
PI-03-0330
Door
AI-01MBDR1600X663-v1
Ridge Bar - 28x28x744mm
F2828-744mm
Eave Frame - 28x28x835mm QTY 2
F2828-835mm
Fascia - 12x60x694mm QTY 4
S1260-694mm
Door Strip - 12x28x1541mm QTY 2
S1228-1541mm
Cover Trim - 12x45x1560mm QTY 4
S1245-1560mm
Finial QTY 2
T-hinge QTY 2
PI-07-0021
“L” Bracket QTY 2
PI-07-0012
Turn Button QTY 2
PI-07-0034
Nail Bag
7
8
9
11
12
10
18
Step 1
Rest the door (No. 6) into the door gable
(No. 1) opening and secure into place with
2x T-hinges (No. 13) using 7x30mm per
hinge.
*Ensure to align the hinges and screws with
the framing on the back of the door.
14x30mm Screws
1
6

50mm
screw
Pre drill
hole
P 3
Please retain product label and instructions for future reference
Step 2
Place the oor (No. 4) onto a rm
and level base. Ensure your base
has suitable drainage and is free
from areas where standing water
can collect. 4
2
3
a
b
a
bb
b
Step 3
Sit the plain gable (No.3) and the rst plain
side (No. 2) onto the oor.
*Ensure the plain gable sits inside the plain
side.
Fix the panels at the corner using
3x 50mm screws.
Do NOT secure the building to the
oor until the roof has been tted.
3x50mm Screws
a
b
a
a
a
a
a
a
a
a
a
b
bb
50mm
screw
Pre drill
hole
Step 4
Rest the assembled door gable (No.1) and the
second plain side (No. 2) onto the oor.
*Ensure the door gable sits inside the plain
sides.
Fix the panels at the corner using
9x 50mm screws.
Do NOT secure the building to the
oor until the roof has been tted.
9x50mm Screws
a
b
2
1
14
7
a
b
Step 5
Attach the “L” brackets (No. 14) to each
end of the ridge bar (No. 7), ensuring
the backs are ush with the edge of the
framing using 2x20mm screws per“L”
bracket.
Fix to both gables centrally
with 2x30mm screws per side.
4x20mm Screws
4x30mm Screws
Pre drill
hole
20mm
screw 30mm
screw
b
a

HANDLE
WITH CARE
12
3
4
30mm
screw
Pre drill
hole
50mm
screw
Pre drill
hole
Felt
tacks
*Felt size: 1413mm
P 4
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Please retain product label and instructions for future reference
8
5
Step 6
Attach an eave frame (No. 8) to
each roof sheet (No. 5) as shown
in the illustration using 3x30mm
screws.
Fix the the assemble roof sheets
onto the gables, securing each
sheet with 8x30mm screws.
22x30mm Screws
b
b
b
b
b
b
Step 7
Once the roof has been xed into
position, secure the building to
the oor using 12x50mm screws.
*Ensure to align the screws with the oor
bearers.
12x50mm Screws
b
Step 8
Cut the felt into 1 sheet and lay
onto the roof, allowing
approximately 50mm of overhang
arond the building.
Fix the felt into position using
32x felt tacks.
32x Felt Tacks

11
11
11
11
30mm
screw
Pre drill
hole
912
9
9
912
30mm
screw
Pre drill
hole
30mm
screw
Pre drill
hole
Pre drill
hole
30mm
screw
P 5
Please retain product label and instructions for future reference
Step 9
Fix the cover trims (No. 11) to
the corners of the building,
securing each trim using
3x30mm screws.
12x30mm Screws
Step 10
Attach the fascia’s (No. 9) and nial’s (No. 12)
to the front and back of the building as
shown in the illustration, using 12x30mm
screws.
*Ensure to trap the felt between the fascia’s
and the building.
12x30mm Screws
10 10
10
Step 11
Secure the door strips (No. 10) to the inside of
the door gable, xing each strip into place
with 4x 30mm screws.
8x30mm Screws
Step 12
Attach the turn buttons (No. 15) to the
door gable as shown in the illustration,
xing each turn button into place using
2x 30mm black screws.
2x30mm Black Screws

It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
P 6
Please retain product label and instructions for future reference
Please retain product label and instructions for future reference