Mercia Garden Products 0619VR3301-V1 User manual

P 1
0619VR3301-V1
19MM LOG CABIN - 3.3X1M VERANDA ADD ON PACK B
2mm Drill bit
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All buildings should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
Please retain product label and instructions for future reference
0619VR3301-V1
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
BUILDING A BASE
When thinking about where the building and base are going to be constructed:
Ensure that there will be access (60mm) to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions. The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for your specic product code
For ease of assembly use a
rubber mallet to t the log
boards. Do NOT use a heavy
hammer.
Ensure to measure and check before cutting
boards.
It is advisable to use a hand
saw when cutting roof and
oor boards.
To ensure log boards are even, use a spirit
level to check each layer has been installed
correctly.
Measure
under the
head
Measure
overall
length
Screws & Nails Bolts To identify the
xings required
for each step use a
measuring tape.
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk

P 2
0619VR3301-V1
Please retain product label and instructions for future reference
3
4
5
6
7
8
9
Overall Dimensions:
Width = 3258mm
Depth = 1000mm
Height = 870mm
Base Dimensions:
Width = 3230mm
Depth = 902mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Bearer - 44x44x3104mm QTY 3
F4444-3104-PT
Log Board - 110x19x326mm QTY 2
LB19RG110-B-326
Log Board - 120x19x326mm QTY 6
LB19-C-326
Log Board - 120x19x1000mm QTY 8
LB19-B-1000
Log Board - 56x19x1000mm QTY 2
LB19RG56-B-1000
2
1
Bearer - 44x44x247mm QTY 2
F4444-247-PT
Floor Board - 120x12x882mm QTY 25
S12120-882
Starter Board - 66x19x326mm QTY 2
LB19RT66-B-326
Log Board - 120x19x326mm QTY 18
LB19-B-326
EXAMPLE BUILDING
There may be extra screws present in the nail bag
70mm Screw x 12
Nail Bag
40mm Screw x 85
Pre-assembly
*Please note:
Each board interlocks at either end in a staggered pattern.
Before securing ensure that the boards are tted properly in
their respective tongues and grooves.

P 3
Please retain product label and instructions for future reference
Pre-Assembly
Follow the instructions for the 19mm Log Cabin
(0619AXNE3326HGDD2SW-V1 OR 0619AXNE3303HGDD2SW-V1)
Your Log cabin should be fully assembled before starting the Veranda.
Your building should look as shown.
Step 1
Parts Needed - No. 1 QTY 3
No. 2 QTY 2
Place the rst Bearer
(No. 1) up to the log cabin and x
to the log cabin bearer using
4x70mm screws.
Attach one small bearer
(No. 2) to each end of the third-
larger bearer using 4x70mm
screws.
8x70mm Screws
a
b
Pre drill
hole
70mm
screw
a
1
1
2
b
1
2

Please retain product label and instructions for future reference
70mm
screw
Pre drill
hole
40mm
screw
8
2
4
Step 2
Parts Needed - No. 4 QTY 2
No. 8 QTY 2
Following the method outlined
in the illustration, secure one
starter board (No. 4) onto each of
the small bearers (No. 2), using
1x70mm screws per board,
ensuring to screw through the
notch into the bearer below.
Make sure that the end of starter
board (No. 4) is ush with end of
the small bearer (No. 2.)
Place the rst two log boards
(No.8) onto the starter boards
(No.4) and rest onto the bearers as
shown in the illustration.
Once in position x the log board
to the inside of the cabin using
2x40mm screws per log board.
*The centre bearer at this
point is not xed into position,
arrange so that the bearer is
central.
4x40mm Screws
2x70mm Screws
P 4
4
8
4
8
.
8
7
5
5
5
6
Step 3
Parts Needed - No. 5 QTY 18
No. 6 QTY 2
No. 7 QTY 6
No. 8 QTY 6
Following the method outlined
in the illutration, continue placing
the boards (No. 5, 7 & 8) on to the
veranda sides as shown in the illus-
trations, ensuring to interlock the
boards.
Once in position x the top log
board (No.6) on each side to the
inside of the cabin using 2x40mm
screws per log board.
4x40mm Screws
Pre drill
hole
40mm
screw
6
5
5
8
7
8
8
7
7
Rubber Mallet
may be required
to t parts.
6
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk

P 5
Please retain product label and instructions for future reference
Step 4
Parts Needed - No. 3 QTY 25
Place the Floor Boards (No. 3)
onto the bearers and secure each
board into place using 3x40mm
screws, ensuring to screw
through the boards into the bear-
ers below.
75x40mm Screws
40mm
screw
Pre drill
hole 3
Step 5
Parts Needed - No. 9 QTY 2
Fix the last two log boards (No.9)
onto the veranda sides using
1x70mm screws per board through
the notches and 2x40mm screws
per board through the boards as
shown in the illustration.
2x40mm Screws
2x70mm Screws
70mm
screw
Pre drill
hole
40mm
screw
9
9
9
Rubber Mallet
may be required
to t parts.
AFTER TREATMENT:
score around protective
cover on glazing and
carefuly peel
covering back
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.
SILICONE
SEALANT
It is ESSENTIAL to seal around all window framing with
sillicone sealant (not included) to minimise water ingress.