Mercia Garden Products 03BUT0606-V1 Instruction manual

P 1
03BUT0606-V1
Buttermere 6x6 Octagonal Summerhouse
2mm Drill bit
x2 Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building has been treated by the
correct application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
Please retain product label and instructions for future reference
General Instructions
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, Wood saw, Step ladder, Hammer and a
Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for you specic product code
For ease of assembly, you
will need a tape measure to
check dimensions of
components.

P 2
03BUT0606-V1
Overall Dimensions:
Width = 1875mm
Depth = 1875mm
Height = 2654mm
Base Dimensions:
Width = 1800mm
Depth = 1800mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
2
134
567
Plain Panel
AI-03BUT0606-V1PP
QTY x3
Door Panel
AI-03BUT0606-V1DP
Window Panel
AI-03BUT0606-V1WP
QTY x4
Roof Panel
AI-03BUT0606-V1R
QTY x8
Floor
AI-03BUT0606-V1F
8
9
10
11
12
13 14 15 16 17
19 20 21
18
PI-07-0011
QTY 16
Window Block
PI-04-0062
Roof Plate
PI-04-0023
Finial
F60106-106mm
OCTAGONAL BOSS
Roof Boss
PI-04-0002
Door Stop
PI-07-0069
Roof Metal Plate
PI-07-0002
QTY 3
Hinge
MBP-121mm (ANGLED CUT)
Roof Panel Point x8
Buttermere roof trim 4318-1107mm
Roof Trim - 1107mm x8
F4444-1100mm(BIRDMOUTH)
Roof Rafter - 1060mm x8
S1295-780mm
Fascia - 780mm x16
Corner Trim - 1799mm
Buttermere corner trim 4318-1107mm
Door
AI-03HEL1010ND
Window
AI-03FW540X1132-V1
QTY x4
PI-07-0018
Press lock
PI-04-0033
Ring Pull
Handle

Nail Bag
50mm Screw x5
40mm Screw x108
20mm Screw x11
30mm Screw x152
Felt Tacks x180
60mm Screw x 32
30mm Black Screw x21
P 3
Please retain product label and instructions for future reference
Step 1
To x the Windows (No. 6)into the panels
that accomodate a window. First x the
Blocks to the Window as shown with
1x30mm screw.
Place the Window into the aperture
and x by screwing though the Block
(No. 21) with 2x30mm screws as
shown.
4x Window block per window.
Screw into the Window rst.
48x30mm screws.
Pre drill
hole
30mm
screw
Step 2
To x the Door (No. 4)into the Door
panel (No. 2). Lay the Door panel at
on the ground and place the Door
within the doorway.
The door can be hung from either
side to suit your needs.
It is important that the door is
placed central in the space provided.
Fix the Hinges (No. 20) to the Door
panel (No. 2) using 4x30mm black
screws.
t21x30mm screws.
Pre drill
hole
30mm
screw
21
Step 3
Place the Floor (No. 7) onto a rm
and level base, ensuring the base has
suitable drainage & is free from areas
where standing water can collect.
The base for this building is symetrical
and any edge can be used as the front
of the building.
6
21
7

3
P 4
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Please retain product label and instructions for future reference
Step 4
Using the Floor as a guide x the side of
two Plain panels (No. 1) together using
3x60mm screws as shown.
Each panel has a top and bottom. The
panels will not align if not arranged as
shown below.
Do not secure the building to the Floor
until the Roof is tted.
3x60mm screws.
Pre drill
hole
60mm
screw
Step 5
Repeating the method shown previously
and still using the Floor as a guide x the
other plain panel and the rst 2 Window
panels (No. 3) together using 3x60mm
screws as shown.
Erecting the panels in this manor
allows for them to be spaced evenly.
Do not secure the building to the Floor
until the Roof is tted.
9x60mm screws.
Pre drill
hole
60mm
screw
3
Panel top Panel bottom
1
1
*Plain panels are interchangeable with the Window panels & Door panel*
Step 6
The remaining panels can be also be
xed into postion.
Secure each panel to each other with
12x60mm screws.
Each panel has a top and bottom. The
panels will not align if not arranged as
shown below.
Do not secure the building to the Floor
until the Roof is tted.
12x60mm screws.
Pre drill
hole
60mm
screw
Panel top Panel bottom
1
23

P 5
Please retain product label and instructions for future reference
Step 7
For the Roof assembly, construct the
framing away from the building.
Use 4x50mm screws to secure the Roof
Metal Plate (No. 18) to the Roof Boss
(No. 15).
4x50mm screws.
Fix the Roof rafters (No. 9) one at a time
to the Boss/Metal plate assembly as
shown with 1x40mm screws per rafter.
8x40mm screws.
Once all rafters are attached, secure the
with 1x60mm screw.
8x60mm screws.
Pre drill
hole
40mm
screw 50mm
screw
60mm
screw
18
15
9
Step 8
From the outside of the building, place
the roof frame into position making sure
that the Roof rafters are each equally
spaced between two panels shown.
Step 9
Secure the Roof framing to the building
with 2x40mm screws per Roof rafter.
Make sure to screw into panel framing.
*Pre-drilling is essential to avoid
splitting*
16x40mm screws.
Pre drill
hole
40mm
screw