Meridian RGB-T-0 Installation instructions

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 1 3/07 Rev 1.2
Installation/Operation Instructions
Fiber Optic RGB & DVI Video Transmission System
Part Numbers:
RGB-T-0 & RGB-R-0
(Single-channel, RGB / DVI Transmitter & Receiver)

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 2 3/07 Rev 1.2
Table of Contents
1.0 Product Description....................................................................................................................3
2.0 Installation..................................................................................................................................3
2.1 Fiber connections...................................................................................................................3
3.0 Product Signal Format & Specifications.....................................................................................4
3.1 RGB resolutions & refresh rates.............................................................................................4
3.2 RGB Video Adjustments ........................................................................................................4
3.3 RGB to DVI conversion..........................................................................................................5
3.4 RGsB Input/Output.................................................................................................................5
3.5 Connectors.............................................................................................................................6
3.6 Conversion Cables.................................................................................................................6
4.0 Front Panel Pinout Assignment Diagram...................................................................................7
4.1 Status Indicators ....................................................................................................................7
5.0 Troubleshooting .........................................................................................................................8
Appendix 1 – Supported Video Resolutions & Refresh Rates...............................................................8
Part Number Variations........................................................................................................................10

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 3 3/07 Rev 1.2
1.0 Product Description
Meridian’s RGB-T/R product is part of Meridian’s new DigiView product family. This state-of-the-art, high
performance video transmission system transmits fully-compliant DVI, RGsB or RGBHV signals over one,
multimode fiber. Optional DVI adapter cables allow easy interface to standard video connection interfaces on
computers, monitors, switches, etc. The RGB-T/R provides real-time, digitized transmission of DVI, RGB and
H&V sync signals. Because it transmits signals in real-time, no video information is lost and is a perfect solution
for dynamic video signals with crystal clear video and no color pixel skewing.
Having both DVI and RGB input/output capability, this system offers an easy upgrade path from RGB to DVI
systems with the same modules. With this dual input/output capability, the user can easily interface RGBHV
sources to DVI monitors and also DVI video sources to standard RGBHV monitors and video switches. The
user can further enhance the video performance with the use of the computer USB interface. This data channel
allows the user to adjust brightness, contrast, H&V position, picture sharpness, color, etc.
This product uses Meridian’s standard 1-slot wide chassis mount card assembly and plugs into the following
Meridian chassis: SR-500/S, SR-1000/S, SR-1200/S, SR-1500/S, and SR-2001 & SR-2000 series 19”
equipment chassis.
2.0 Installation
The RGB/DVI series products are one-slot wide cards and, as such, occupy one slot in Meridian’s standard
chassis (SR-500/S, SR-1000/S, SR-1200/S, SR-1500/S, and SR-2001 & SR-2000 series 19” equipment
chassis). To install in the chassis, orient the card with the Meridian logo at the top of the module and slide onto
the top and bottom card guides in the chassis. Press securely on the top and bottom of the module to ensure
that it is fully seated in the chassis so that the electrical connector mates with the chassis-mounted
motherboard. Once installed, manually tighten the two thumbscrews located at the top and bottom of the card.
Do not use tools to secure these and do not over tighten.
Note: A fully populated subrack should have forced-air cooling to avoid excessive heat buildup inside the
chassis. A fan assembly tray (P/N FA-2000/1) with three (3) fans is available from Meridian and should be
installed under the 19" SR-2000/1 whenever possible.
2.1 Fiber connections
There is one ST style fiber connection interface on the transmitter and a corresponding ST style fiber
connection on the receiver. These modems are designed for multimode fiber (either 62.5 or 50 micron core
diameter fiber). The maximum fiber distance is listed below:
Fiber type Maximum distance
62.5/125um 300 meters
50/125um (standard performance) 1000 meters
50/125um (high bandwidth) 2000 meters
If the fiber distance is larger than that listed above, the video signal quality will be compromised and may not
operate properly.

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 4 3/07 Rev 1.2
3.0 Product Signal Format & Specifications
The RGB series products transmit and receive the following signals over one multimode fiber:
•DVI, RGBHV, RGsB (YPbPr)
•VGA, SVGA, SGA, SXGA & UXGA - Auto selection of resolutions and refresh rates from 640x480 to
1600x1200 x 60Hz
•HDTV resolutions of 480p, 720p and 1080i (DVI & RGBHV), 1080p (DVI only)
•H&V Sync frequency range of 60Hz to 150Hz (vertical), 30 to 130kHz (horizontal)
•RGB processing – 24-bits, no compression or scaling
•Input impedance/level – RGB 75ohm,
3.1 RGB resolutions & refresh rates
Meridian’s RGB-T/R-0 transmission system is designed to automatically sense and configure itself to work with
many of the standard video resolutions and screen refresh rates. When first connected to an RGBHV video
source, the transmitter/receiver pair will determine the incoming signal characteristics, search its internal
firmware database and modify the characteristics of the system to properly encode, transmit and decode the
signal. This initial recognition will cause the monitor’s display to go blank for approximately 1 second while the
system synchronizes with the incoming signal. Once completed the video transmission will continue.
The Resolution/Refresh rate table Appendix 1 lists the various video resolutions and refresh rates these
modules support – at the time of this writing. If needed, please contact Meridian for an updated list of the
resolutions/refresh rates this product supports.
3.2 RGB Video Adjustments
There are occasions where the resolution of the video source does not exactly match the resolution of the
monitor or minor adjustments in color, contrast, picture position need to be made. In this case, the quality of the
video may be somewhat compromised. In order to correct this, the RGB-T/R modules can be adjusted slightly
to make minor corrections in the quality of the video signal. These adjustments include Horizontal/Vertical
position, color, brightness and contrast. The steps below identify the proper procedure for installing and running
the supplied software.
There are no physical hardware adjustments on this equipment. All of the adjustments are made with the
supplied software that can be installed on your Windows 2000/XP computer. Please follow the instructions
below on the software installation.
RGB-HV Interface software installation
1. Insert the card into the chassis or card cage and turn the RGB-HV transmitter’s power supply
2. Insert the USB cable into the USB connector on the transmitter’s front panel and into an unused USB
port on your computer (This supports either USB1.1 or USB2.0 ports)
3. Follow the various screen prompts to install the software from the CD supplied with the product.
4. Once installed you can go to Windows Device Manager (Ports (COM & LPT)) to ensure that the
appropriate COM port has been installed
5. Click START button on task bar, then Programs and choose RGBCARDINTERFACE program. The
interface should come up. Select choose the appropriate com port. If necessary, you can select an
alternate port where the hardware resides.
6. There are three (3) tabs on the top of this window – “File”, “Settings”, and “Presets”. Click on the
“Settings” tab only. The “Display Adjustment” screen will appear.
7. The only adjustment that may need to be made is Phase Adjust. This may need adjustment if some
level of unwanted ‘ghosting’ or vertical bars appears on the display. Normally, no adjustments will be
necessary.

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 5 3/07 Rev 1.2
8. If you need to revert back to the original setup conditions, click the “Presets” tab of the ‘RGB Card
Interface Transmitter’ and select Current screen size.
9. This concludes the fine tuning adjustments of the RGB-HV transmission system
3.3 RGB to DVI conversion
These modems are capable of operating in both RGBHV & DVI modes. Both the Tx & Rx
units can be individually configured to transmit/receive either RGBHV or DVI. In order to do
this, one switch on the Tx and Rx boards must be set. The table and figure below show the
location of this switch on the circuit board and the proper configuration of the switch for the
desired mode of operation.
The photo below shows the location of the bank of switches. The only switch in this bank of
10 switches that needs to be configured is Switch #1 (far left switch). The default position is
ON (up) for RGB operation. Each of the Tx/Rx modules can be configured individually so that,
if desired, you can make a conversion between RGBHV & DVI. The above table indicates
how each of these configurations can be accommodated using this RGB/DVI selector switch.
This switch bank can be accessed either by using a small screwdriver to reach inside the slot
module’s cover on the right side. Otherwise, the side cover can be carefully removed (screws
in each corner of the card) where the switch can then be accessed.
3.4 RGsB Input/Output
These units can also be used to transmit and receive RGsB (RGB w/sync on Green) video
signals. The selector switch on the appropriate Tx/Rx units must be set to transmit or receive
this signal. In order to input or output an RGsB video signal, both switch 1 & 2 must be in the
ON (down) position.
Note: To convert to or from DVI using RGsB, please follow the table in section 3.3 for the
correct switch setting for the DVI interface selection.
RGB/DVI Selector Switch
Mode (Tx or Rx) Tx Switch #1 Rx Switch #1
RGB (In) - RGB (out) - Default OFF (up) OFF (up)
RGB (In) – DVI (out) OFF (up) ON (down)
DVI (In) – RGB (out) ON (down) OFF (up)
DVI (In) – DVI (out) ON (down) ON (down)
RGsB Selector Switch
Mode (Tx or Rx) Transmitter (RGB-T-0) Receiver (RGB-R-0)
Switch #1 Switch #2 Switch #1 Switch #2
RGB (In) - RGB (out) - Default OFF (up) OFF (up) OFF (up) OFF (up)
RGsB (In) – RGB (out) OFF (up) ON (down) OFF (up) OFF (up)
RGB (In) – RGsB (out) OFF (up) Off (up) OFF (up) ON (down)
RGsB (In) – RGsB (out) OFF (up) ON (down) OFF (up) ON (down)

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 6 3/07 Rev 1.2
3.5 Connectors
The tables below identify the various connectors on the modules. The DVI-I connector is mounted to the
module’s front panel on both the transmitter and receiver.
Connectors
Video Standard DVI-I female (with RGBHV analog inputs/outputs)
DVI-I to RGBHV (HD-15 female) molded adapter (dongle)
RGB adjustment 4-pin USB (type B)
Optical Multimode - ST
3.6 Conversion Cables
There are several types of DVI connectors that are mounted on standard computers and monitors. Meridian
offers standard adapter cables (6 ft length) to properly interface these various connectors to our RGB-T/R
modules. The table below identifies the type of connectors and the corresponding Meridian adapter cable that
should be used. The connector on the opposite end of the cable is the standard DVI-I connector that interfaces
to the RGB transmitter/receiver modules.
HD15(M)
DVI-I
Connector
DVI-D
Connector
Computer/Input/Output
Device Adapter Cable
Part Number
Red Grn Blu H-Syn V-Syn
C-HD15-6
C-DVI-I-6
C-DVI-D-6
C-BNC-6
BNC Connectors
Switch #1
Switch #2

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 7 3/07 Rev 1.2
4.0 Front Panel Pinout Assignment Diagram
Figure 4.1 below shows the front panel layout, connector location, indicator location and pinout assignment for
both the RGB-T and RGB-R modules. This diagram shows the video pinouts for the on-board DVI-I video
connector.
Figure 4.1
RGB-T-0 & RGB-R-0 Front Panel Layout Diagrams
4.1 Status Indicators
There are function status indicator lights associated these modules. They are identified as follows:
Power: Green (ON)
Diagnostic: Green (OK), Red (alarm)
Tx Carrier (transmitter only): Green (OK), Red (alarm)
Rx Carrier (receiver only): Green (Present)/Red (Error)
DVI active: Green
RGB active: Green
SHV (sync H&V): Green (present)
SOG (sync on green): Green (present)
USB active: Green (Rx-data), Red (Tx-data)
RGB/DVI-T RGB/DVI-R
Pinout Diagram Pinout Diagram

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 8 3/07 Rev 1.2
5.0 Troubleshooting
Below is a listing of several problems that may arise during the installation & operation of the modules. If you
are having difficulty installing or operating the modules please refer to this list below.
Problem: Module does not fit in chassis slots
Action: Check module orientation. Meridian “Globe” must be oriented on the top left hand side of the
module
Make sure the card guides in the chassis are aligned with the extrusion on the module
Problem: Card power LED does not light when power to the module/subrack is applied or power indicator
turns on and off
Action: Check power supply to ensure that it is plugged in and turned on. If flashing continues, move
module to another chassis or location in the same chassis, if available.
Problem: No Video
Action: 1 - Check the modem locations to ensure that the RGB-T module is connected to the video
source (computer, camera, etc) while the receiver module (RGB-R) is connected to the video
output device (monitor, etc.)
2 – Check to ensure that the modules are in the proper mode of operation (RGB or DVI) –
onboard switch #1 (see section 3.4)
If the problem still persists after reviewing the above items, please contact Meridian technical support (516-285-
1000).
Appendix 1 – Supported Video Resolutions & Refresh Rates
The table below lists the presently-supported video resolutions and refresh rates. Meridian continues to expand
the supported variations and will update this list as they become available.
If you have any questions about other resolution/refresh rates, please call our technical service personnel.

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 9 3/07 Rev 1.2
Video
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
1152x864 53.70 60
1152x864 63.17 70
1152x864 64.94 72
1152x864 67.50 75
1152x864 77.30 85
1152x864 91.84 100
1152x864 110.8 120
1152x864 131.5 140
1152x864 135.0 144
1152x864 141.7 150
1280x720 44.6 60
1280x720 52.6 70
1280x720 53.9 72
1280x720 56.4 75
1280x720 64.0 85
1280x720 76.1 100
1280x720 92.9 120
1280x720 109.3 140
1280x720 112.5 144
1280x720 117.6 150
1280x960 60.0 60
1280x960 70.0 70
1280x960 71.9 72
1280x960 75.0 75
1280x960 85.9 85
1280x960 101.4 100
1280x960 123.1 120
1280x1024 64.0 60
1280x1024 74.7 70
1280x1024 76.9 72
1280x1024 80.0 75
1280x1024 91.2 85
1280x1024 108.0 100
1600x1200 75.0 60
Video
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
640x480 31.47 60
640x480 35.16 70
640x480 37.86 72
640x480 37.50 75
640x480 43.27 85
640x480 50.90 100
640x480 61.80 120
640x480 72.92 140
640x480 75.00 144
640x480 78.30 150
640x480 90.6 170
640x480 108.0 200
800x600 37.88 60
800x600 43.81 70
800x600 48.08 72
800x600 46.88 74
800x600 53.67 85
800x600 63.60 100
800x600 77.16 120
800x600 90.74 140
800x600 94.10 144
800x600 98.23 150
800x600 112.5 170
800x600 134.5 200
1024x768 48.36 60
1024x768 56.48 70
1024x768 57.91 72
1024x768 60.02 75
1024x768 68.68 85
1024x768 81.40 100
1024x768 98.9 120
1024x768 116.9 140
1024x768 119.9 144
1024x768 125.8 150
1024x768 143.8 170

700 Elmont Rd, Elmont, NY 11003, Tel: [phone]; Fax: [phone]
www.Meridian-tech.com
Page 10 3/07 Rev 1.2
Part Number Variations
The table below indicates the part numbers and product description that are included in this manual.
Transmitter Receiver Description
RGB-T-0M RGB-R-0M RGBHV & DVI video transmitter/receiver pair, multimode, shelf mount
RGB-T-0R RGB-R-0R RGBHV & DVI video transmitter/receiver pair, multimode, rack mount
Note: Shelf mount (“M”) and rack mount (“R”) units can communicate with each other.