Metra Electronics 99-5825S User manual

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APPLICATIONS
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-5825
Ford Fiesta 2011-up
•ISODINHeadunitprovision
•Driverinformationcircuitsandbuttons
•PaintedSilverorMatteBlacktomatchfactoryfinish
WIRING & ANTENNA CONNECTIONS(SoldSeparately)
Wireharness:
•XSVI-5524-NAVFordinterface2011-up
Antennaadapter:
•40-EU10multi-appadapter
PanelRemovalTool•PhillipsScrewdriver•SocketWrench•CuttingTool
C
AB
•A)RadioHousing•B)RadioISOBrackets
•C)(6)#8x3/8”Phillipstrussheadscrews
TOOLS REQUIRED
KIT FEATURES
KIT COMPONENTS
99-5825S
99-5825B

Table of Contents
Dash Disassembly
–FordFiesta2011-up 3-4
Kit Assembly
–FordFiesta2011-up,ISODINheadunitprovisions 5
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
99-5825
Caution
Metra recommends disconnecting the negative battery terminal before beginning any
installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*NOTE: Refer Also to the instructions included with the aftermarket radio.
NOTE: This kit comes pre-programmed for vehicles equipped with SYNC. It will not operate
properly in vehicles equipped without SYNC unless it is programmed.
Programming for vehicles without SYNC:
1. Turn on the ignition.
2. Press and hold the kit’s menu button for ten seconds.
3. Release the menu button and test the kit’s buttons for proper operation.

1. Unsnapandremovethepaneloverthe
 displayatthetopofthedash.(FigureA)
2. Removetwo7mmhexscrewsfromthe
 topoftheradiopanel.(FigureB)
3. Unclipandremovetheradiotrimpanel
 includingthevents.(FigureC)
Continued on next page
3
Dash Disassembly
99-5825
(Figure A)
(Figure B)
(Figure C)

4
Dash Disassembly
99-5825
(Figure B)
(Figure C)
4. Removetwo7mmhexholdingradio
 andradiochassistogether(fromtopof
 panel).(FigureA)
5. RemovetwoT-20Torxandunclipthe
 twoventsfromthefactoryradiopanel.
 (FigureB)
6. RemovetwoT-20Torxfrompassenger
 airbaglightandremoveit.(FigureB)
7.Asmallcutisrequiredinthesubdash
 forclearance.(FigureC)
(Figure A)

5
Kit Assembly 99-5825
(Figure A)
(Figure B)
(Figure C)
1. Snapthefactoryventsintotheradio
 panel.(FigureA)
2. MounttheISObracketstotheheadunit
 withthescrewssuppliedwiththeunit.
 (FigureB)
3. Mounttheradiobracketassemblyto
 theradiopanelusingthesupplied
 screws.(FigureC)
4. Mountthefactoryairbagindicatorto
 theRadioPanelusingthesupplied
 screws.(FigureA)
5. Locatethefactorywiringharness
 andantennapluginthedash.Metra
 recommendsusingthepropermating
 adaptersfromMetraand/orAXXESS.
6. Reassembledashinreverseorder
 ofdisassembly.
NOTE: This kit comes pre-programmed
for vehicles equipped with SYNC. It will
not operate properly in vehicles equipped
without SYNC unless it is programmed.
Programming for vehicles without SYNC:
1. Turn on the ignition.
2. Press and hold the kit’s menu button
for ten seconds.
3. Release the menu button and test the
kit’s buttons for proper operation.
ISO DIN head unit provisions

Notes

Notes

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-5825
REV. 7/13/11