Metra Electronics 99-9605B User manual

REV. 1/25/2017 INST99-9605B
INSTALLATION INSTRUCTIONS FOR PART 99-9605B
METRA. The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
CAUTION! All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
• ISO DIN radio provision with pocket (NAV models only)
• ISO DDIN radio provision
• Provision for HVAC relocation
(vehicle must have a lower console)
• Painted matte black
• A) Radio housing • B) Radio brackets • C) Pocket • D) HVAC trim panel with pocket • E) (6) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS
Wiring Harness: • 70-9401 • 70-1787 (amplified models) (sold separately)
Antenna Adapter: • 40-VW10
• Panel removal tool • Phillips screwdriver
• Torx T-20 screwdriver • Cutting tool
• 86-9001 radio removal keys (qty. 2 for NAV models)
TOOLS REQUIRED
Porsche 911 (996) 1999-2005
Porsche Boxster (986) 1997-2004
99-9605B
A
Table of Contents
BCED
Dash Disassembly ..............................................2-4
Kit Preparation....................................................... 5
Kit Assembly
–ISO DIN radio provision with pocket...................... 6
–ISO DDIN radio provision ...................................... 7
–Models without factory NAV ................................. 7

99-9605B
2
Dash Disassembly
For models without factory
navigation:
Upper dash:
1. Insert the radio removal keys into
the radio until they click in, and
then remove the radio. (Figure A)
Note: The curved portion of the
radio removal keys should point
towards the middle of the radio.
2. Using a panel removal tool, remove
the HVAC trim panel. (Figure B)
3. Remove (2) Phillips screws on
each side of the HVAC controls,
unplug and then remove.
(Figure C)
4. Unsnap and remove the switch
panels from each side of the
radio opening. (Figure D)
Note: 2002-2005 911 models
have one “U” shaped
panel instead.
5. Remove (6) Torx T-20 screws
securing the radio frame assembly.
(Figure E)
Note: The (2) middle screws are
located deep in the dash on the
sides of the radio opening.
Continued on the next page
(Figure A)
(Figure D)
(Figure C)
(Figure B)
(Figure E)

99-9605B
(Figure F) (Figure H)
(Figure G) (Figure I)
3
Dash Disassembly
Lower dash:
6. Unsnap the trim panels from the
sides of the lower console.
(Figure F)
Note: Unclip from the front of the
vehicle, and then pull back.
7. Unsnap and remove the factory
CD tray/pocket. (Figure G)
For models equipped with a
DSP controller:
8. The controller will need to be
relocated to the inside of the lower
dash. The controller must stay
connected in order for the factory
amplifier to function.
9. Unclip and remove the DSP trim
panel. (Figure H)
10. Remove (2) T-20 Torx screws to
remove the DSP controller.
(Figure I)
Continue to Kit Preparation

99-9605B
4
Dash Disassembly
3. Remove (6) Torx T-20 screws
securing the radio frame assembly.
(Figure C)
Note: The (2) middle screws are
located deep in the dash on the
sides of the radio opening.
Continue to Kit Assembly
(Figure B)
(Figure A)
For models with factory navigation:
1. Insert the radio removal keys into
the radio until they click in, and
then remove the radio. (Figure A)
Note: The curved portion of the
radio removal keys should point
towards the middle of the radio.
2. Unsnap and remove the switch
panels from each side of the radio
opening. (Figure B)
Note: 2002-2005 911 models
have one “U” shaped
panel instead.
(Figure C)

99-9605B
5
Kit Preparation
1. Cut and remove the center bar and
the mounting positions from the
inside of the radio frame assembly
removed in dash disassembly to
allow room for the radio. (Figure A)
2. Re-route the climate control
wiring to the lower console
area of the dash.
Continue to kit assembly
(Figure A)
Remove shaded area
Do not cut these plastic pieces,
leave them intact

99-9605B
6
Kit Assembly
ISO DIN radio provision with pocket
(NAV models only)
1. Secure the pocket to the radio
housing using the (4) 8 x 3/8”
Phillips screws provided.
(Figure A)
2. Remove the metal DIN sleeve
and trim ring from the
aftermarket radio.
3. Slide the radio into the housing/
pocket assembly and then secure it
using the screws supplied with the
radio. (Figure B)
4. Slide the radio housing into the
radio frame assembly removed in
dash dissassembly. (Figure C)
5. Locate the factory wiring harness
and antenna connector in the
dash and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Test the radio for
proper operation.
6. Place the radio brackets around
the radio housing and frame
assembly and then secure it using
the (2) 8 x 3/8” Phillips screws
provided. (Figure D)
7. Reassemble the dash in reverse
order of disassembly.
(Figure B) (Figure D)
(Figure A) (Figure C)

99-9605B
7
Kit Assembly
ISO DDIN radio provision
1. Slide the radio into the radio
housing and then secure it using
the screws supplied with the radio.
(Figure A)
2. Slide the radio housing into the
radio frame assembly removed in
dash dissassembly. (Figure B)
3. Locate the factory wiring harness
and antenna connector in the
dash and complete all necessary
connections to the radio and HVAC
controls. Metra recommends using
the proper mating adapter from
Metra and/or AXXESS. Test the
radio for proper operation.
4. Place the radio brackets around
the radio housing assembly and
then secure it using the (2) 8 x 3/8”
Phillips screws provided.
(Figure C)
5. Reassemble the upper dash in
reverse order of disassembly.
For models without factory
navigation:
1. Secure the HVAC controls into the
lower location of the lower console
using the screws removed in dash
disassembly. (Figure A)
2. Snap the climate trim panel with
pocket into the lower console
location. (Figure B)
3. Reassemble the lower dash in
reverse order of disassembly.
(Figure B)
(Figure A)
(Figure A)
(Figure C)
(Figure B)

REV. 1/25/2017 INST99-9605B
INSTALLATION INSTRUCTIONS FOR PART 99-9605B
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation
of this product, please call our Tech Support line
at 1-800-253-TECH. Before doing so, look over
the instructions a second time, and make sure
the installation was performed exactly as the
instructions are stated. Please have the vehicle
apart and ready to perform troubleshooting
steps before calling.
METRA. The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION

INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-9605B
METRA. The World’s best kits.®metraonline.com1-800-221-0932 © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
REV. 1/25/2017 INST99-9605B
¡PRECAUCIÓN! Todos los accesorios, interruptores,
paneles de control climático y especialmente las luces
indicadoras de bolsa de aire deben estar conectados
antes de encender el encendido. Además, no extraiga la
radio de fábrica con la llave en la posición de encendido,
o mientras el vehículo esté funcionando.
Indice
• Herramienta para quitar paneles
• Destornillador Phillips • Destornillador Torx T-20
• Llaves de remoción de radio 86-9001 (cant. 2 para
modelos NAV) • Herramienta de corte
HERRAMIENTAS REQUERIDAS
• Provisión de radio ISO DIN con cavidad (solo modelos NAV)
• Provisión de radio ISO DDIN
• Provisión para la reubicación HVAC (el vehículo debe tener
una consola inferior)
• Pintura negra mate
• A) Carcasa del radio • B) Soportes del radio • C) Cavidad • D) Panel de moldura HVAC con cavidad
• E) (6) tonillos Phillips 8 de 3/8”
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
CABLEADO Y CONEXIONES DE ANTENA
Arnés de cables: 70-9401 • 70-1787 (Modelos amplificados) (se venden por separado)
Adaptador de antena: • 40-VW10
Porsche 911 (996) 1999-2005
Porsche Boxster (986) 1997-2004
99-9605B
A B CED
Desmontaje del tablero ......................................2-4
Preparación del kit ................................................ 5
Ensamble del kit
–Provisión de radio ISO DIN con cavidad ............... 6
–Provisión de radio ISO DDIN ................................. 7
–Para los modelos sin navegación de fábrica ......... 7

99-9605B
Desmontaje del tablero
2
Para los modelos sin navegación
de fábrica:
Tablero superior:
1. Inserte las llaves de remoción de
radio en el radio hasta que encajen
y luego retire el radio. (Figura A)
Nota: la porción curva de las
llaves de remoción del radio
deben apuntar hacia la parte
media del radio.
2. Con una herramienta de remoción
de panel, quite el panel de la
moldura HVAC. (Figura B)
3. Quite (2) tornillos Phillips de
cada lado de los controles HVAC,
desconecte y luego quite.
(Figura C)
4. Suelte a presión y quite los paneles
del interruptor de cada lado de la
abertura del radio. (Figura D)
Nota: los modelos del 911 2002
a 2005 tienen un panel en forma
de “U” en su lugar.
5. Quite los (6) tornillos T-20 Torx que
sujetan el ensamble del marco
del radio. (Figura E)
Nota: los (2) tornillos de en
medio se ubican adentro del
tablero en los lados de la
abertura del radio.
Continua en la siguiente pagina
(Figura A)
(Figura D)
(Figura C)
(Figura B)
(Figura E)