Metra Electronics 99-8249 User manual

CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
Installation instructions for part 99-8249
• ISO DIN radio provision with pocket
•ISO DDIN radio provision
•Painted to match factory finish
•A) Radio housing trim panel • B) Radio brackets • C) Pocket • D) (8) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1761
Antenna Adapter: • 40-LX11
• Panel removal tool • Phillips screwdriver
• 10 mm nut driver or socket wrench
TOOLS REQUIRED
Toyota Camry 2015-up
99-8249
ADC B

99-8249
Dash Disassembly
1. Unclip and remove the console
storage tray. (Figure A)
2. Push down on the collar below the
shift knob then unscrew the shift
knob. (Figure B)
3. Remove (2) Phillips screws from
the shifter trim, unclip and remove
the trim. (Figure C)
4. Remove (2) Phillips screws
securing the factory pocket, unclip
and remove the pocket. (Figure D)
Continued on next page
(Figure A) (Figure C)
(Figure B) (Figure D)

99-8249
5. Unclip and remove the vent panel
above the radio. (Figure E)
6. Remove (4) 10 mm bolts securing
the radio and climate control
assembly (2 above and 2 below).
(Figure F)
7. Unplug and remove the assembly
from the dash.
8. Remove (10) Phillips screws
securing the factory radio brackets
to the assembly. Note: (4) Phillips
screws securing the climate
controls will be needed for kit
assembly.
9. Unclip the climate controls from
the assembly then remove the
(2) white panel clips and keep
for kit assembly.
Continue to kit assembly
(Figure E) (Figure F)
Dash Disassembly

99-8249
Kit Assembly
(Figure A)
(Figure B)
(Figure C)
ISO DIN radio provision with pocket
1. Attach the white panel clips
removed in step 9 of dash
disassembly to the radio housing
trim panel.
2. Clip the climate controls onto the
radio housing trim panel.
3. Connect the radio brackets to the
radio housing trim panel with (4)
#8 x 3/8” Phillips screws supplied.
(Figure A)
4. Mount the pocket to the
bracket/panel assembly with the
(4) remaining #8 x 3/8” Phillips
screws supplied. (Figure B)
5. Remove the metal “DIN” sleeve and
trim ring from the aftermarket radio.
6. Slide the aftermarket radio into the
assembly and secure with screws
supplied with the radio. (Figure C)
7. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
8. Mount the new radio assembly into
the dash and reassemble the dash
in reverse order of disassembly.

99-8249
Kit Assembly
ISO DDIN radio provision
1. Attach the white panel clips
removed in step 9 of dash
disassembly to the radio housing
trim panel.
2. Clip the climate controls onto the
radio housing trim panel.
3. Connect the radio brackets to the
radio housing trim panel with (4)
#8 x 3/8” Phillips screws supplied.
(Figure A)
4. Slide the radio into the assembly
and secure with screws supplied
with the radio. (Figure B)
(Figure A) (Figure B)
5. Locate the factory wiring harness
and antenna connector in the
dash, and complete all necessary
connections to the radio. Metra
recommends using the proper
mating adapter from Metra and/or
AXXESS. Re-connect the negative
battery terminal and test the radio
for proper operation.
6. Mount the new radio assembly into
the dash and reassemble the dash
in reverse order of disassembly.