Michelin DPS User manual

Digital Gauge
™
USB
Digital Power
Source
+ -
Programmable
3
Inflation
USER GUIDE
PROGRAMMABLE 12V
High-Power TYRE INFLATOR
* ON THE EXAMPLE OF A 175/70 R13 CAR TYRE 62003
04/21

Thank you for purchasing the
MICHELIN programmable 12V High-Power
tyre inflator.
Please read the operating instructions carefully before using your inator. Improper use can
cause damage to property and possibly harm the user. When using the inator ensure the
vehicle is parked in a safe location, off the road, with the vehicle handbrake on and where
your personal safety is not at risk.
This inator can inate car tyres up to 50 psi (do not inate space saver tyres) and
bicycle tyres up to 100 psi. Higher pressures can be achieved in cycle tyres due to their
smaller air volumes compared to car tyres. Only suitable for vehicles with a negative
earth. Check your vehicle owner’s manual. When inating vehicle tyres this inator
should ONLY be used for car tyres and bicycle tyres. Low pressure items such as sports
balls and small inatable toys may also be inated using the adaptors provided.
MAX POWER REQUIREMENT DURING NORMAL USE: 10A / 120W
WARNING!
 The inator contains no user serviceable parts – DO NOT OPEN.
 Never allow children to use this tyre inator.
 Inspect the tyre inator before each use.
 Do not use the inator if bent, broken, melted, burnt, wet or any of the
components are damaged.
 Do not leave connected to 12V DC socket unattended.
 Do not kink or block the air hose while the inator is working.
 Never overinate.
 Under or overinated tyres can be dangerous.
 Never run for more than 10 minutes. After each 10 minute run allow inator to
cool down.
 Always ensure that regular weekly checks are carried out to the vehicle
manufacturer’s recommended pressures including the spare, but excluding space
saver tyres. Always check before a long journey or after loading or unloading
thevehicle.
 Always check pressures in an ambient temperature, never immediately after a long
journey.
THIS PRODUCT COMPLIES WITH DIRECTIVE 2006/42/EC, ROHS DIRECTIVE 2011/65/EU
AND ANNEX VI OF DIRECTIVE 2000/14/EC.
USER GUIDE
High-Power TYRE INFLATOR

Functions
Maximum pressure:
Pressure accuracy:
Pressure resolution:
Maximum current:
Fuse size:
Hose length:
Power cord:
SPEcIFIcations
50 psi for car tyres
100 psi for cycle tyres
+/- 1 psi up to 50 psi
Bar / psi / kPa
10A / 120W
15A glass
60 cm (approx.)
300 cm (approx.)
1
2
4
5
6
7
8
9
10
11
3
1. On/Off button
2. 12V power outlet source
3. White LCD digital display
4. Pressure pre-set buttons
5. Superbright LED lights
6. 60 cm (approx.) high pressure air hose
with tyre valve connector
7. 5V USB outlet source
8. LED push button switch
9. Bar, psi & kPa button/Reset button
10. 300 cm (approx.) power cord with
fused 12V power plug (side of unit)
11. Adaptors (snap-in storage at rear
of unit)

DPS™ DIGITAL POWER SOURCE – Features
12V POWER SOCKET
Lifting the left hand cover reveals a 12V power socket (2) This is suitable for accessories,
such as inspection light or vacuum cleaner with a maximum rating of 12A.
USB PORT
Under the right hand cover is a single 5V USB port (7) suitable for charging mobile devices
with a maximum rating of 0.5A.
TYRE INFLATION
1. With the On/Off button in Off position, unwind power cord completely from the storage
compartment and plug into your vehicle’s 12V power plug socket. Wait a few seconds
until digital display shows zero. PLEASE NOTE - when the On/Off button is in the Off
position, it protrudes from the unit slightly. When in the On position the button is ush
to the unit.
2. To choose desired pressure format bar, psi and kPa, press the yellow button. Each press
of the button cycles through the pressure format.
3. Uncoil high pressure hose and screw tyre valve connector onto the tyre valve. When
connected correctly the gauge will display the current pressure in the tyre. If this is the
tyre pressure as stated in your vehicle’s handbook, you can simply remove the tyre valve
connector.
4. If the tyre is below the recommended pressure (as specied in your vehicle handbook),
press either the or pre-set button to adjust to the correct tyre pressure. Holding
either button for 1 second will increase/decrease the pre-set pressure rapidly.
NOTE: The unit has a built in memory and will default to the last tyre pressure set in the
gauge display of the inator. You can then scroll up or down using the or buttons
to set the correct tyre pressure (as specied in your vehicle handbook).
5. If the tyre is above the recommended pressure remove the valve connector from the tyre
valve and release some air from the tyre. Follow steps 3 and 4 to inate the tyre to the
correct pressure.
6. Press On/Off button to turn inator on,Your tyre inator will now inate your tyre until
the selected pre-set is reached. It will continue to run for a few seconds when it has
reached the selected pressure, this is a feature of the in-built pressure sensor to ensure
the correct pressure has been attained.
7. Remove the tyre valve connector from the tyre valve. Take care when unscrewing the
tyre valve connector.
8. If you are inating multiple tyres then follow the procedure stated from 3 to 7.
above. If the 12V power supply is disconnected then always reconnect the 12V power
supply before connecting the high pressure hose to the tyre valve. If there is a power
interruption during the ination cycle, please follow the reset procedure outlined in the
trouble shooting guide.
+
-
+
-

ADAPTORS
Included with your tyre inator, on the back of the display unit, is a snap-in storage compartment
containing various adaptors, to enable you to inate other items. To avoid overination, always follow
the manufacturer’s instructions on the items to be inated.
Small toy inator adaptor
Sports ball adaptor
Presta valve adaptor
(high pressure cycle tyres)
12V Power Plug
TO REPLACE FUSE:
Undo knurled ring anti-clockwise.
anti-clockwise
knurled ring
knurled ring
fuse
Replace fuse and knurled ring (max. 15A).

Trouble Shooting
 Gauge does not illuminate: Check that the plug is fully inserted into 12V socket.
 Unit fails to run with switch in ‚On‘ position: Check internal plug fuse (15A glass type).
Your car may require the ignition key to be turned to the accessory position.
 Unit fails to stop on pre-set: Check you are following the setting instructions correctly.
Check that you have set the correct pre-set pressure.
 Power lead/plug becomes hot: If power lead is coiled, uncoil to full length. Ensure 12V
socket is clean with no debris in it. Ensure 12V plug components are tight and clean.
 Gauge appeares to read incorrectly or is unreadable: When the tyre valve connector is
attached before switching the unit on, ensure the gauge is reading your current tyre
pressure.
 Gauge reads 0.0: Disconnect valve connector from the tyre. Remove plug from power
source for at least 5 seconds, reconnect to power. Press and hold yellow reset button
until display shows all the digits. It then returns to 0.0. Connect valve connector to tyre.
 Unit is running but tyre is not inating: Check that the ryre valve connector is correctly
tted to the tyre valve.
 Gauge does not display when tyre valve is connected: Ensure tyre valve is correctly
connected to the tyre valve connector.
 Gauge displays ERR message: Connect the 12V power plug to the vehicle’s 12V supply.
Do not connect the valve connector to the tyre valve. Allow the gauge to settle for a
few seconds, press and hold the yellow reset button for 5 seconds. This will reset the
pressure sensor. If the problem persists the pressure sensor has failed - please contact
customer support.

Customer enquiries:
We’re at your service. Let us help
you nd a better way forward.
Tel: [phone]
[e-mail]
Manufactured and distributed under licence by
Helix Automotive GmbH, Fischeräcker 4, DE-74223 Flein
© 2021 Michelin, www.michelin-lifestyle.com
MICHELIN and/or the Michelin Man Device and/or BIBENDUM
are trademark(s) owned by, and used with the permission of,
the Michelin Group.
PROGRAMMIERBARER 12V HOCHLEISTUNGS-
KOMPRESSOR
https://www.helix-automotive.com/qr/62003/userguide/de/
DE: Bedienungsanleitung – FR : MODE D’EMPLOI –
IT: MANUALE D’USO – ES: MANUAL DE USUARIO –
TR: KULLANIM KILAVUZU
COMPRESSEUR 12V HAUTE PERFORMANCES
PROGRAMMABLE
https://www.helix-automotive.com/qr/62003/userguide/fr/
COMPRESSORE AD ALTA PRESTAZIONE
12V PROGRAMMABILE
https://www.helix-automotive.com/qr/62003/userguide/it/
COMPRESOR DE ALTO RENDIMIENTO
PROGRAMABLE DE 12V
https://www.helix-automotive.com/qr/62003/userguide/es/
PROGRAMLANABİLİR 12V YÜKSEK
PERFORMANSLI KOMPRESÖR
https://www.helix-automotive.com/qr/62003/userguide/tr/
MANUAL DE USUARIO