Michelin Ratchet Locking Jack Stands User manual

User Guide
2000 kg
Ratchet Locking
Jack Stands
52003
04/21
Maximum
Hight
Maximum
rated load

2
FUNCTIONS
EN
1. Soft grip saddle
2. Ratchet bar
3. Safety pin
4. Locking handle
5. Frame
2
4
5
3
1

2 3
EN
2000 kg ratchet locking jack stands
User Guide
SAVE THESE INSTRUCTIONS! For your safety, read, understand, and follow the
information provided with and on this jack stand. The owner and operator of this
equipment must have an understanding of this jack stand and safe operating pro-
cedures before attempting to use. The owner and operator must be aware that use
of this product may require special skills and knowledge. Instructions and safety
information must be conveyed in the operator‘s native language before use of this
jack stand is authorized. If any doubt exists as to the safe and proper use of this jack
stand, remove from service immediately.
Inspect jack stands before each use. Do not use if broken, bent, cracked, or damaged
parts (including labels) are noted. Any jack stand that appears damaged in any way,
operates abnormally or is missing parts, must be removed from service immediately.
If the jack stand has been, or suspected to have been, subjected to a shock load (a
load dropped suddenly, unexpectedly upon it), immediately discontinue use and re-
move from service. It is recommended that an annual inspection be done by qualied
personnel.
PRODUCT DESCRIPTION / SAFETY INSTRUCTIONS
MICHELIN 2000 kg Ratchet Locking Jack Stands are designed to safely support
level, rated capacity loads, specically vehicles, for extended periods. Stamped steel
construction and ductile iron ratchet bars ensure safety, strength and stability.
BEFORE USE
1. Verify that the product and the application are compatible.
2. Before using this product, read the owners manual completely and familiarize
yourself thoroughly with the product, its components and recognize the hazards
associated with its use.
3. Always check the vehicle owners or service manual for location of proper lift and
support points.
SPECIFICATIONS
Maximum rated load: 2,000 kg
Minimum hight: 280 mm
Maximum hight: 428 mm

4
EN
WARNING & SAFETY INFORMATION!
- Jack stands that are used on a sloping surface can easily slip to the side or kink.
- The strength of the jack stands is greatly reduced if loads are not centred or if
sideways forces are applied to them.
- Always ensure that jack stands are in perfect condition (no cracked welds, no
loose, missing or damaged components). If it is suspected that they have been
subjected to an excessive load or an impact, immediately discontinue use and
remove from service.
- It is advisable to inspect jack stands before use to ensure that they have not
deteriorated (no corrosion, cracking, or deformation).
- Use only as specied by the manufacturer.
- Use no more than a single pair of stands.
- Use the jack stands only on a hard level surface.
- Securely chock the wheels that are still in contact with the ground.
- Make sure that each stand is securely located under a strong point of the
vehicle. Consult the vehicle manufacturer’s handbook for guidance.
- Exercise extra care when using a three wheeled vehicle or trailer.
- Upper and lower part of the jack stands must not be separated.
- DO NOT EXCEED MAXIMUM LOAD.
- Never use on sloping, inclined, uneven ground or on a soft surface.
- When supporting a vehicle, place jack stands only at support points specied
by the vehicle manufacturer.
- Ensure that the load and the jack stands are stable before working under the
vehicle.
- Centre the load on the saddle of the jack stand.
- Never use an additional support.
- Do not modify the jack stands in any way.
The manufacturer accepts no liability for any injury or damage resulting from a
failure to comply with these warnings.

4 5
EN
INSTRUCTIONS FOR USE
1. For correct stability choose a hard and at surface.
2. Engage the hand brake and put the vehicle into gear.
3. Adjust the ratchet bar to the desired height and lock it with the locking handle.
4. Secure the jack stand with the safety pin.
5. Jack up your vehicle as specied by the manufacturer.
6. Centre the load over the saddle of the jack stand. It is advisable to leave the jack
in place when the weight of the vehicle is supported by the jack stand.
7. To remove the jack stand, jack the vehicle up again, pull the jack stand free, then
lower the vehicle to the ground.
8. Protect the jack stands from corrosion by cleaning them, then wipe over with an
oily rag before storage.
Handbreak on Leave car in
gear
Use on a at surface
Customer enquiries:
We’re at your service. Let us help
you nd a better way forward.
Tel: [phone]
[e-mail]
Manufactured and distributed under licence by
Helix Automotive GmbH, Fischeräcker 4, DE-74223 Flein
© 2021 Michelin, www.michelin-lifestyle.com
MICHELIN and/or the Michelin Man Device and/or BIBENDUM
are trademark(s) owned by, and used with the permission of,
the Michelin Group.