MICODUS MV720 User manual

MV720 User Manual V2.0
Learn how to set up your new MiCODUS Tracker
Copyright ©2022 MiCODUS | All Rights Reserved
R

2.Specifications
GPS+
GLONASS+LBS
Historical Route
Playback
9-90V Wide
Working Voltage
Vibration
Alarm
Remotely Cut Off
/Resume Fuel
Realtime
Tracking
Overspeed
Alarm
Tow Alarm Geo-fence
Power
Disconnect Alarm
Lifetime Free
Tracking Platform
1. Main Features
Model
Weight
Dimensions
MV720
53g
31mm(L) * 31mm(W) * 57mm(H)
Device Information
Working Voltage
Working Current
Sleep Current
Battery Capacity
Working Temperature
Working Humidity
Working Frequency
SIM Card
Cellular Antenna
Positioning Type
GPS Antenna
Cold Start
Hot Start
Tracking sensitivity
GPS Channels
Position Accuracy
GPS+GLONASS+LBS
Built-in
≤32 Seconds
≤1 Second
-162 dBm
64
5-10m
2G GSM/GPRS: 850/900/1800/1900MHz
Nano SIM Card
Built-in
DC 9-90V
<30 mA
<15 uA
3.7V 80mAh Lion Polymer battery
-20℃- 75℃
10%-85%RH non-condensing
Working Parameters
Cellular Specifications
GNSS Specifications

3.How to manage the tracker to get online?
Normal SIM
Step 1
Step 2
Please get a suitable SIM card from your local place. The
SIM card must meet below points:
It must be compatible with the 2G GSM network
Please enable SMS, call, internet data traffic of the SIM card
Remove the PIN code
Enable the caller ID display feature
Use Nano size SIM card for the tracker
Please inquire the SIM card provider for the exact correct APN
information
1 2 3 4
SIM card installation

apn123456+space+
apn name
apnuser123456+
space+apnuser
apnpasswd123456+
space+apnpassword
apn ok
apnuser ok
apnpasswd
ok
apn123456 cmnet
apnuser123456 cmnet
SMS Command
Format Reply Example Note
Please get the exact correct APN name from
local SIM card provider.“cmnet” is just an
example of APN name.
apnpasswd123456 123
lf the SIM card operator doesn’t have APN user
name,then please ignore this configuration
Please get the exact correct APN name from local SIM card provider.Take the tracker to a
good signal place for operation and configure the APN for it as below:
Step 4
FUEL PUMP LINE VOLTAGE:5V-30V
FUEL PUMP LINE CURRENT:< 60A
Step 3 Wiring
Configure APN
Car Battery
Fuel Pump Line
+
-
Fuel
Pump
NOTE
: After installed SIM card correctly , it is very important to
connect the tracker with external power no less than 12V for power supply
before operation!
9-90V DC

4. Package Content
GPS Main Unit
Function Cable
Pick
User Guide
Genuine Packing Box
x 1
x 1
x 1
x 1
x 1
LED Event State
State
Searching for network
GSM LED (GREEN) Network has been registered Flash every 1 second
Solid
Flash every 1 second
Solid
GPS has fixed
GPS is in fixing
Device is working but stopped more than 5min
Device has not been turn on
Device ran out of battery
GPS LED (Blue)
ALL LED ALL LED TURN OFF
Note: The APN information is very important, it must 100% correct to match with the sim card of
the tracker, if you configured wrong APN, the tracker also will reply "SET APN ok" but it will
can't get online!
Step 5 Indicator status description

5. Functions Explanation
* Set admin number by this sms command:
admin123456+space+mobile number with country code
* Send this sms command from the admin number to cut
off fuel:555
* If the network signal and satellite signal both are available, when the equipment speed
exceeds 20km/h, the fuel circuit will not be cut off immediately, it will cut off intermittently
till the speed is below 20km/h, then just can be completely cut off.
* In the tracker has network signal and but no satellite signal, the fuel circuit will be cut
off intermittently, after 2, 3 minutes it will be cut off completely;
* If the tracker stopped more than 5 minutes, the fuel circuit will be cut off immediately,
and then connected, but if you vibrate the tracker or vibrate the tracker the fuel cirsuit will
be cut off immediately;
a. Vibration Alert:
This vibration alert function just work under stationary
status. How to use this function:
b. Cut Off Fuel/Resume Fuel
* Enable the device to enter into arm mode by this
sms command: 111
* Conifgure the alarm ways by this sms command:
vibalm123456
* Set admin number by this sms command:
admin123456+space+mobile number with country code
* Keep the device under stationary status more than 5min to let it enter into sleep arm mode;
* Vibrate the device then the tracker will send the vibration alarm messages
For example:
admin123456 0086134********
admin ok
cut oil ok
MV720
555
For example:
admin123456 0086134********
admin ok
arm ok
MV720
111
vibrate sms alarm set ok
vibalm123456
Please follow with the quick user guide carefully!
:About the cut off fuel function, firstly please
make sure the fuel circuit is connecting to main power. Secondly,
it has 3 different performance, please read it carefully:
NOTE

Unable to connect to
tracking platform
Check the APN and settings.
Check whrther the data service of SIM card is enabled.
Check the balance of SIM card.
Tracker shows offline
Check whether external power is still connected.
Check if the vehicle entered netword blind area.
Check the balance of SIM card.
7. Troubleshooting
Type Use
Location drift
In area with poor GNSS signal (tall building around or
basement), drifting may happen.
Check whether vibration happens around to trigger the
accelerator.
Unable to locate
Make sure the top side facing upward without metallic things
shielded.
Make sure it’s not in area with no satellite coverage.
No command reply
Make sure command format is correct.
Vehicle may be in network blind area.
Make sure SIM card is well inserted and has SMS servi.
6. Installation Recomendation
1) The decice should face up to the sky.
2) Metal therma barrier of heating layer of the windshield affects the signal.
1
3
4
2
Inside the head light
Under the pedal
Inside the front cover
Inside the taillight
component
or plastic
Under Front Dash
Inside Door Pedal

Functions Command Format Explanation
8. Full SMS Commands List
Set Admin Number
Back to Factory Setting
admin123456+space+mobile number
with country code
begin123456
After sent this sms command, all your configuration
will be cleared and the device will get back to
factory default settings
The password just can be 6 digitals
After sent this sms command, the configurations
will be saved and the device will restart
Please add your country code as prefix
of the admin number
Restart rst
Please get the exact correct APN name from the
SIM card provider of the tracker, "cmnet" is China
Mobile's APN name
apn+123456+apn content
APN
IP&Port
Domain
Google Maps Link
adminip+123456+space+ip
+space+port
Micodus tracking platform's IP: 47.254.77.28;
Port: 7700
MiCODUS server domain: d.micodus.net, Port: 7700
SZCS,123456,DOMAIN=d.micodus.
net:7700
G123456# or where
Password Change password+old password+space+
new password
If the SIM card operator doesn't have APN user,
then please ignore this configuration
If the SIM card operator doesn't have APN
password, then please ignore this configuration
apnuser+123456+space+content
apnuser+123456+space+content
V:A: Indicates the device has GPS signal;
V:V: Indicates the device doesn't have GPS signal;
2019-11-26 10:17:01: Date and Time;
S: 000km/h: Speed of the tracker
Bat:5: Battery level of the backup battery of the
tracker, it has 6 levels: "6" means 100% , "5" 80%,
"4" means 60%, "3" means 40%, "2" means 20%,
"1" means 10%;
ACC: off: The status of the car engine;
7201000006: ID number of the device;
S26: GSM signal is 26
G06: GPS signal is 06
p:46000, l:13152, c:63162: p,l,c this 3 parameters
means the LBS code
Data Upload Frequency upload123456+space+time Time interval scope: 10-180s
If east time zone, needn't input sign "+", for example, if
the time zone is East 8, then the sms command should
be sent like this: timezone123456 8
Time Zone timezone+123456+space+GMT No.

Movement alarm distance scope: 100-1000m
firmware version、ID、IP、port、domain、APN
admin number, SOS number,move distance, overspeed,
auto arm time, auto disarm time, alarm interval
BAT:10 GPRS: GSM: GPS:A/V ACC:on/off oil:on/off
power:on/off
Parameter Query
Status
Arm
Sleep Mode
param1
param2
status
111 or SF
sleep123456 time
sleep123456 shock
sleep123456 off
Functions Command Format Explanation
Vibrate Alarm
Tow Alarm towA,B A: 1-4, 1: SMS alarm, 2: Call alarm, 3: SMS+Call,
4: Platform alarm; B: Distance (500-10000m)
vibx,y x=1-3( 1: SMS alarm, 2: Call alarm, 3: SMS first then Call );
y=1-9,1 is the most sensitive
Cancel sleep mode
vibcall+123456
Vibrate call alarm set ok ( If device keep stationary more than
5 minutes the device will enter into sleep mode automatically,
vibration, sms commands and call can wake up it)
Vibrate sms alarm set ok(If device keep stationary more than
5 minutes the device will enter into sleep mode automatically,
vibration, sms commands and call can wake up it)
vibalm+123456
Disarm 000 or CF
Cut Off Fuel 555
Resume Fuel 666
Movement Alarm move+alarm distance
Overpeed alarm speed scope: 20-150km/h
Overspeed Alarm speed+123456+space
+speed limit
IMEI Checking imei+123456
If device keep stationary more than 5 minutes the device will
enter into sleep mode automatically, sms commands and
call can wake up it
If device keep stationary more than 5 minutes the device will
enter into sleep mode automatically, vibration, sms
commands and call can wake up it

E-mail: [email protected]
Skype: MiCODUS
9. Any Questions?
10. Download the APP
Download on the
APP Store
Download for
Android
Search "MiCODUS" in iOS APP store or Google Play
Store, or just scan the QR code as below to download
MiCODUS APP: