MICODUS ML150 User manual

ML150 User Manual V1.0
Learn how to set up your new MiCODUS Tracker
Copyright ©2022 MiCODUS | All Rights Reserved
R

1. Main Features
2.Specifications
Real-time
Tracking
Voice
Monitor
Overspeed
Alarm
Vibration
AlarmGeo-fence
Historical
Route
Built-in
Magnet
Waterproof
IP65 1500mAh
Model
Weight
Dimensions
Charging Time
Battery Working Time
ML150
58.4g
36mm(L) * 23mm(W) * 54mm(H)
Around 5 hours
3-5 days under tracking mode
Device Information
Working Voltage
Working Current
Sleep Current
Battery Capacity
Working Temperature
Working Humidity
Working Frequency
SIM Card
Cellular Antenna
Positioning Type
GPS Antenna
Cold Start
Hot Start
Tracking sensitivity
GPS Channels
Position Accuracy
GPS+BEIDOU+LBS
Built-in
≤32 Seconds
≤1 Second
-162 dBm
64
5-10m
2G GSM/GPRS 850/900/1800/1900Mhz
Nano SIM Card
Built-in
DC 3.4V - 4.5V
4V/Average 45mA
4V/less than 5mA
3.7V 1500mAh Lion Polymer battery
-20℃- 75℃
10%-85%RH non-condensing
Working Parameters
Cellular Specifications
GNSS Specifications
Shift Alarm

Mircrophone,Magnetic External Interface
3. Activate Device
LED Event State
Charging
Charger inserted and battery has been fully charged
Charger has not been inserted
Searching for network
POWER LED (RED)
CELL LED
(YELLOW) Network has been registered
Solid
Dark
Dark
Flash every 1 second
Solid
GPS has fixed
GPS is in fixing Flash every 1 second
Device is working but stopped more than 5min
Device has not been turn on
Device ran out of battery
GPS LED (BLUE)
ALL LED
Solid
ALL LED TURN OFF
Install the SIM card via the correct direction as below:
APN,ApnName,User,
Password# SET APN OK APN,orange, orange,orange#
APN,internet#SET APN OKAPN,ApnName#
SMS Command
Format Reply Example
Note
If the SIM card has APN user and APN
password, then use this command.
If the SIM card operator doesn't have APN
user and APN password, then please use this
command.
Normal SIM
Note: The APN information is very important, it must 100% correct to match with the sim card
of the tracker, if you configured wrong APN, the tracker also will reply "SET APN ok" but it will
can't get online!
Please get the exact correct APN name from local SIM card provider.Take the tracker
to a good signal place for operation and configure the APN for it as below:

4. Package Content
GPS Main Unit
USB Charging Cable
User Manual
Quick User Guide
Genuine Packing Box (Optional)
Hard-Wired Car Charger (Optional)
x 1
x 1
x 1
x 1
x 1
x 1
5. Functions Explanation
a. Working modes setting
* ML150 has 3 working modes to meet different tracking
demands, the setting command format is as below:
MODE,A,T1,T2#
* Example:
MODE,1,10,3600# (this means the device will upload data by 10s interval under moving
status and 3600s interval under stationary status)
MODE,2,0900,1# (this means the device will start working via mode 2 at 09:00am, and
it will upload data every 1 hour)
MODE,3,0900,1# (this means the device will start working via mode 3 at 09:00am, and
it will upload data every 1 hour)
A=1 (Tracking mode)
T1: upload interval of GPS data in moving status,
unit: second,10-3600s; default: 10s
T2: upload interval of GPS data in static status,
unit: second, 180-65535s; default: 3600s
A=2 (Power saving mode)
T1: interval start time,format: HH:MM
T2: time interval,range: 1-72
unit: hour,default interval: 24hours
A=3 (Hibernation mode)
T1: interval start time,format: HH:MM
T2: time interval,range: 1-72
unit: hour,default interval: 24hours
For example:
MODE,1,10,3600#
MODE,2,0900,1#
SET MODE OK
SET MODE OK
MODE,3,0900,1#
SET MODE OK
ML150
Please follow with the quick user guide carefully!
* Note : The difference between mode 2 and mode 3 is that under mode 2 the
device can be wake up by sms, call and vibration, under mode 3, the device will just can be
wake up by teardown alarm.

b. Voice Monitor:
* Set center number by this sms command:
CENTER,A,center number#
For example:
* Switch the tracker to voice monitor mode
by this sms command:MONITOR#
*Dial the sim number of the tracker from the center
number, then the tracker will pick up the call automatically
and you will can remote monitor the voice around it.
CENTER,A,12345678910#
MONITOR#
SET CENTER NUMBER OK
SET MONITOR MODE OK
ML150
c. Vibration Alert:
This vibration alert function just work under stationary
status. How to use this function:
*Enable the device to enter into arm mode by this
sms command: ARM#
*Conifgure the alarm ways by this sms command:
SENALM,A,M#
A=ON/OFF, default: OFF;
M=0/1/2, way of alarming,
0 :GPRS only, 1: SMS+GPRS, 2: GPRS+SMS+phone call, default:1
* Configure SOS numbers for the tracker by this sms
command:SOS,A,1st number,2nd number,3rd number#
3 SOS numbers supports at the most
* Keep the device under stationary status more than 5min to let it enter into sleep arm mode;
* Vibrate the device then the tracker will send the vibration alarm messages
For example:
SOS,A,12345678910#
SET SOS NUMBER OK
ARM#
SET ARM MODE OK
SENALM,ON,1#
SET VIBRATE ALARM OK
ML150
6. Applications
Personal Valuables Suitcase Vehicles

Unable to connect to
tracking platform
Check the APN and settings.
Check whrther the data service of SIM card is enabled.
Check the balance of SIM card.
Tracker shows offline
Check whether external power is still connected.
Check if the vehicle entered netword blind area.
Check the balance of SIM card.
7. Troubleshooting
Type Use
8. Full SMS Commands List
Location drift
In area with poor GNSS signal (tall building around or
basement), drifting may happen.
Check whether vibration happens around to trigger the
accelerator.
Unable to locate
Make sure the top side facing upward without metallic things
shielded.
Make sure it’s not in area with no satellite coverage.
No command reply
Make sure command format is correct.
Vehicle may be in network blind area.
Make sure SIM card is well inserted and has SMS servi.
APN Setting
Server Setting
If set with IP: SERVER,0,IP,Port#
APN,Network name[,name,password]#
If set with Domain Name: SERVER,1,
Domain,Port# SERVER,1,d.micodus.net,7700#
SERVER,0,47.254.77.28,7700#
A=old password, six digitals, digital range: 0-9,
default：000000;
B=new password, six digitals, digital range: 0-9
APN,CMNET# (if no name & Password)
APN,internet,internet,internet# (if with name
& Password)
Check IMEI IMEI#
Restore factory settings
Version Inquiry
FACTORY#
VERSION#
Revise the instruction
password PASSWORD,[A],[B]#
Functions Command Format Explanation

Functions Command Format Explanation
Parameter Inquiry
Latitude&Longitude
Inquiry
Map URL Inquiry
Check All Alarms Status
PARAM# Check ID,IMEI,APN, IP,PORT,TIMER,Center
number,SOS number,Time Zone
WHERE#
URL#
ALARM#
Status Inquiry STATUS#
BATTERY: XX% (Built-in Battery Power Percent)
NET: CLOSED (No Network) FAILED (Connecting
Network or Failure) SUCCESS(Connected
to Network),
NONE (No GSM Signal)
HIGH / MED / LOW (Signal Strength)
GPS: CLOSED (GPS Module Closed) FIXED,
N(Positioned and satellite number) UNFIX,
0 (Not Positioned yet)
ANGLE: 20 (the data upload angle)
SENSOR: ON/OFF (the status of the shake
sensor)
LEVEL: 3 (the sensitivity of the shake sensor)
STATE: ARM/DISARM (the defense status of
the device)
Time Zone Setting
Set the angle upload
ANGLEREP,[X][,A][,B]#
ANGLEREP,OFF#
GMT,Time zone orientation,Whole
Time Zone[,Half Time Zone]#
X=ON/OFF,default:ON; A=5~180 degrees,diversion
angle degree, default: 30 degrees;B=2~5 seconds,
detecting time, default: 3 seconds.
GMT,E,8# (if no half time zone)
GMT,W,9,30# (if has half time zone)
NOTE: Parameter : E / W; 0 ~ 12; 0/15/30/45
Add SOS Administr-
ator Number
Delete SOS
Administrator Number
Add Center Number
SOS,A,1st number,2nd number,3rd
number#
SOS,D,1st number,2nd number,3rd
number# or SOS,D,1,2,3#
CENTER,A,center number#
CENTER,A,13800138000#
NOTE: Only center number can be used
for cutting off fuel.
Set 3 numbers at a time:
SOS,A,13800138000,1380013800 1,13800138002#
Set the first numberseparately:
SOS,A,13800138000#
Set the second number separately:
SOS,A,,13800138001#
Means to set 3rd number separately:
SOS,A,,,13800138002#
Directly delete the number: SOS,D,13800138000#
Delete 1st number: SOS,D,1#
Delete 2nd number: SOS,D,2#
Delete the 2nd and 3rd number: SOS,D,2,3#
Query current mileage
A=ON/OFF, On/Off mileage calculation,
default: Off
B=0~999999, Mileage initial value , unit: km ;
default: 0, mileage return to zero
Mileage Statistics
MILEAGE,[A],[B]#
MILEAGE#

Delete Center Number CENTER,D#
Functions Command Format Explanation
Working Mode Setting
A=1/2/3, 1:Tracking mode 2:Power saving mode
3:Hibernation mode; Default mode: 1
A=1
T1: upload interval of GPS data in moving status,
unit: second,10-3600s; default: 10s
T2: upload interval of GPS data in static status,
unit: second, 180-65535s; default: 3600s
A=2
T1: interval start time,format: HH:MM
T2: time interval,range: 1-72
unit: hour,default interval: 24hours
A=3
T1: interval start time,format: HH:MM
T2: time interval,range: 1-72
unit: hour,default interval: 24hours
MODE,A,T1,T2#
Sleep Mode Setting
Voice Monitor Mode
Track Mode
Heartbeat Packet
Upload
Sensor Sensitivity
MONITOR#
TRACK#
HBT,time#
MOTION,sensitivity#
SLEEP#
SLEEP,OFF#
NOTE: Before monitoring the voice around the device,
the user must change the device to this monitor mode
firstly.
NOTE: After used the voice monitor mode, user can
switch the device back to track mode by this command.
HBT,3#
NOTE: Range :1-60min, default 3min.
MOTION,2#
NOTE: Sensitivity Level：1-9 (1-9 is from week to
strong vibration)
NOTE: After set this sleep mode, the device will
enter into sleep mode automatically when the
device keep stationary status more than 5min.
Note: The difference between mode 2 and mode 3 is that
under mode 2 the device can wake up by sms, call and
vibration, under mode 3, the device will just can wake up
by sms and call, vibration will can't wake up it.
Arm manually
Disarm manually
Overspeed Alarm
Setting
ARM#
DISARM#
SPEED,[A][,B][,C]#
SPEED,OFF#
Set the device into arm mode
Set the device out of arm mode
A=ON/OFF, open or close over speed alarm,
default：OFF
B=1～255(km/h), speed limit, default：100(km/h);
C=0/1, way of alarm, 0 : GPRS only, 1: SMS+GPRS,
default：1.

Vibration Alarm
Setting
Shift Alarm
Setting
SENALM,[A][,M]#
SENALM,OFF#
SHIFT,[A][,B][,M]#
Example: SHIFT,ON,100,1# ( Means Setting 100
meters shift alarm range, when the ignition turned
off, vehicle’s 100 meters’ shift will trigger the alarm.)
A=ON/OFF; default:ON
B=Shift Distance (Range: 100-9999m)
M=0/1/2; way of alarm, 0 : GPRS only, 1: SMS+
GPRS, 2: GPRS+SMS+CALL, default:1
SHIFT,OFF#
A=ON/OFF, default: OFF;
M=0/1/2, way of alarming, 0 :GPRS only, 1: SMS+
GPRS, 2 : GPRS+SMS+phone call, default:2
Functions Command Format Explanation
BATALM, [A][, M]#
BATALM,OFF#
：ON; M=0/1, way of alarming,
A=ON/OFF, default
0: GPRS only, 1: SMS+GPRS, default：1；
Low Battery Alarm
Setting

E-mail: [email protected]
Skype: MiCODUS
9. Any Questions?
10. Download the APP
Download on the
APP Store
Download for
Android
Search "MiCODUS" in iOS APP store or Google Play
Store, or just scan the QR code as below to download
MiCODUS APP: