MICRO-EPSILON scanCONTROL 3000/BL User manual

Page 1
scanCONTROL 3000/BL / 3002/BL
Assembly Instructions
scanCONTROL 3000/BL / 3002/BL
1. Warnings
Connect the power supply and the display-/output device according to the safety
regulations for electrical equipment. The supply voltage must not exceed the specified
limits.
> Risk of injury, damage to or destruction of the sensor
Avoid shocks and impacts to the sensor. Avoid constant exposure of the sensor to dust
and splashes of water. Avoid exposure of sensor to aggressive materials (detergents,
cooling emulsions).
> Damage to or destruction of the sensor
Read the detailed operating instructions before operating the sensor.
These instructions are available online at www.micro-epsilon.com.
2. Notes on CE Marking
The following apply to the scanCONTROL 30xx/BL:
- EU Directive 2014/30/EU,
- EU Directive 2011/65/EU
The sensor is designed for use in industrial applications.
The sensor fulfills the specifications of the EMC requirements, if the instructions in the
operating instructions are followed.
3. Proper Environment
- Protection class: IP67
- Temperature range
Operation: 0 ... +45 °C (+32 ... +113 °F), for free circulation of air
Storage: -20 ... +70 °C (-4 ... +158 °F)
- Humidity: 5 - 95 % (non-condensing)

Page 2
scanCONTROL 3000/BL / 3002/BL
4. Laser Safety
The scanCONTROL 30xx/BL sensors operate with a semiconductor laser with a wave-
length of 405 nm (visible/blue). Operation of the laser is indicated visually by the LED
on the sensor, see operating instructions, Chap. 3.3.
When operating the scanCONTROL 30xx sensors, the relevant regulations according to
IEC 60825, Part 1 of 05/2014 and the applicable accident prevention regulations must
be followed. The laser warning labels for Germany have already been attached. For
other non German speaking countries, an IEC standard label is included in delivery and
the versions valid for the user’s country must be attached before the device is put into
operation for the first time.
iIf both warning labels are covered over when the unit is installed, the user must
ensure that supplementary labels are applied.
Laser radiation. Close your eyes or immediately turn away if the
laser beam hits the eye. Irritation or injury of the eyes possible.
Laser Class 2M
The sensors fall within laser class 2M (IIM). The laser is operated on a pulsed mode, the
maximum optical power is ≤ 10 mW. Attach the following warning labels to the cover
(front and rear side) of the sensor housing:
LASER RADIATION
DO NOT STARE INTO BEAM
OR EXPOSE USERS OF
TELESCOPE OPTICS
CLASS 2M LASER PRODUCT
IEC 60825-1: 2014
P≤10mW, P ≤10mW; E≤6mW/cm²;
0 P
λ= 405nm; F = 0...25kHz, t = 7µs...∞
COMPLIES WITH 21 CFR 1040.10 AND 1040.11
EXCEPT FOR CONFORMANCE WITH
IEC 60825-1 ED. 3., AS DESCRIBED IN
LASER NOTICE NO. 56, DATED MAY 8, 2019
Fig. 1 LLT30xx-xx/BL Fig. 2 Only for USA
iMark the laser area recognizable and everlasting.
scanCONTROL
LASER RADIATION
DO NOT STARE INTO BEAM
OR EXPOSE USERS OF
TELESCOPE OPTICS
CLASS 2M LASER PRODUCT
IEC 60825-1: 2014
P≤10mW, P ≤10mW; E≤6mW/cm²;
0 P
λ= 405nm; F = 0...25kHz, t = 7µs...∞
COMPLIES WITH 21 CFR 1040.10 AND 1040.11
EXCEPT FOR CONFORMANCE WITH
IEC 60825-1 ED. 3., AS DESCRIBED IN
LASER NOTICE NO. 56, DATED MAY8, 2019
LASER
APERTURE
Fig. 3 Sensor
with laser
labels

Page 3
scanCONTROL 3000/BL / 3002/BL
5. Connections, LED Displays
1 2
1 Multifunction port (power supply, I/O)
2 Ethernet port
Multifunction Port
Designation Sensor
connector pin
Cable color
PCR3000-x
Notes
+Ub 9 Red + 11 V - 30 V DC
(rated value 24 V); max. 5 W
GND 2 Blue 0 V
+Laser on/off 3 White Available with SI option
-Laser on/off 1 Brown
RS422 12 Red-blue RS422
input or output
/RS422 11 Gray-pink
GND RS422 10 Purple Ground connection RS422
In1 4 Green Switching input In1
In2 6 Yellow Switching input In2
In3 8 Gray Switching input In3
In4 5 Pink Switching input In4
GND-In 7 Black Ground connection In
Shield Housing Black Not electrically connected to GND
2
3
4
5
6
7
8
9
1
10
11
12
GND: Galvanically isolated from In1, In2, In3, In4,
RS422, laser on/off
Laser on/off: Input galvanically isolated from GND,
In1, In2, In3, In4, RS422
In1, In2, In3, In4, RS422: Input galvanically isolated
from GND and laser on/off
12-pin screw connector, view on solder side (cable)
RS422, Synchronization
The RS422 connection (pins 11 and 12 of the multifunction port) can be used in either
of the following configurations:
- RS422 (half-duplex): Load user modes, sensor control and transmit measurement
results (Modbus RTU or ASCII format).
- Synchronization/triggering: Synchronization or triggering using switching signals

Page 4
scanCONTROL 3000/BL / 3002/BL
Trigger, Encoder, Mode Switching
The switching inputs of the multifunction port can either be used for incoder input,
trigger input or for load previously stored user modes.
The signal levels are switchable for all switching inputs between LLL (TTL logic) and
HLL (HTL logic):
- LLL level: Low 0 V … 0.8 V, high 2.4 V … 5 V, internal pull-up/down switchable resis-
tor 10 kΩ
- HLL level: Low 0 V … 3 V, high 11 V … 24 V (permitted to 30 V), internal pull-up/
down switchable resistor 10 kΩ
- Pulse duration: ≥ 5 µs
External Laser Switch-off, Optional
Externally switching off the laser is implemented as a hardware solution and is a top
priority. The laser can also be switched off by software.
This function is offered by sensors with the /SI option.
Use a serial key switch in the control circuit to switch of the laser.
With standard sensors, connecting the supply voltage activities the laser light source in
the sensor.
Wiring details are available in the operating instructions, Chap. 5.2.6.
Ethernet Connection, Standard Connection to PC
RJ45 connector 8-pin. screw connector (sensor side)
Pin no. Color of stranded hook-
up wire SCR3000A-x
Pin no. 10BaseT,
100BaseTX
1000BaseT
1 White (orange) 5 Tx+ D1+
2 Orange 6 Tx- D1-
3 White (green) 8 Rx+ D2+
4 Blue 1 D3+
5 White (blue) 2 D3-
6 Green 7 Rx- D2-
7 White (brown) 3 D4+
8 Brown 4 D4-
1View on pin side
of male cable
connector
2
3
4
5
6
7
8
1
View on solder side (ca-
ble) of screw connector
(A-coded)

Page 5
scanCONTROL 3000/BL / 3002/BL
- The sensor supports an automatic, sensor-specific IP address in the link-local net
(169.254.x.x). No collision detection is implemented. This is also the default setting.
- The sensor supports DHCP. This setting is activated by default and has priority over
search the link-local net.
- The sensor scanCONTROL 30xx/BL supports Power over Ethernet.
If the sensor is connected to a POE-capable network adapter/
switch and you also use the power supply of the multifunction
port, these two power supplies must be galvanically islolated.
> Damage to the sensor and/or Ethernet card!
- A fixed IP address can be assigned.
Use the sensorTOOL program to make specify the sensor settings described
above.
The program is available online at https://www.micro-epsilon.de/download/software/
sensorTOOL.exe.
LED Displays
LED Laser LED Data LED Error
Yellow: Laser an Green: Measure-
ment is active
Red, flashes: Error code,
see operating instructions
Chap. 11.
Green, flashes:
Data transmission
is active
The LED Data flashes green, long during active transmission
and short for controller accesses.
6. System Requirements
scanCONTROL Configuration Tools
The following minimum system requirements are necessary:
- Windows 7, Windows 8 or 8.1, Windows 10 (each 32 bit and 64 bit)
- 1-GHz or faster (32 bit and 64 bit) processor / 1 GB RAM (recommended 4 - 8 GB)
- Screen resolution: 1024 x 768 (recommended 1920 x 1080)
scanCONTROL 3D-View
The following minimum system requirements are necessary:
- Windows 8 or 8.1, Windows 10 (each 64 bit)
- 1-GHz or faster (64 bit) processor
- 1 GB RAM (recommended 16 GB)
- Screen resolution: 1024 x 768 (recommended 1920 x 1080)
- Graphics card / GPU with OpenGL 3.1 or higher

Page 6
scanCONTROL 3000/BL / 3002/BL
7. Quick Start, Initial Operation, Software
Mount the sensor according to the installation instructions.
Install the software.
You will find the software online on the
product website of the sensor or in the down-
load area:
https://www.micro-epsilon.
de/2D_3D/laser-scanner/Software/
downloads/.
Follow the dialog through the installation
process.
A. Reading the installation help
B. Installing the software
C. Additional information in the online docu-
mentation
Connect the sensor to the PC using the optionally available SCR3000A-x Ethernet
cable.
Connect the shield of the power supply cable to the PE grounding conductor of
the main power supply. Close unused connection plugs with the included protec-
tive caps. Turn on the power supply (24 VDC).
Please wait until the scanCONTROL measuring system is recognized by the PC.
This may take a few seconds.
Now you can operate the scanCONTROL measuring system with the scanCON-
TROL software packages.
iOperating a scanCONTROL sensor via Ethernet may require the IP settings of the PC/sensor or the firewall settings to be adjusted, see Chap. 5.2.5 of the operating
instructions
The connectors for Ethernet and the multifunction port include a screw connector.
Loosen the screws connection before you remove the connector from the socket.
iOnly connect the sensor to the peripheral equipment, if it is disconnected from the power supply, i.e. only when the power supply is switched off. The sensor
needs a warm-up time of typically 20 minutes for high precision measurements.

Page 7
scanCONTROL 3000/BL / 3002/BL
8. First Profile
Now start the scanCONTROL Configuration Tools software. Click on Display
Profiles in the main window.
If the software shows the error message No scanCONTROL found in the status line,
please check the Ethernet connection between scanCONTROL and the PC.
On the left side you can adjust the settings for your measurement task, the right side
shows the profile data and information about the measurement.
9. How to Access Profile Data
Profile data of scanCONTROL can be accessed via:
- GigEVision and GenICam for digital cameras via Ethernet interface
- SDK for fast application integration (C, C++, C# and others)
Please refer to the respective SDK documentation for further information on accessing
the profile data.
10. Unpacking, Included in Delivery
- 1 scanCONTROL 30xx/BL sensor with integrated controller
- 1 PCR3000-5 multifunction cable, length 5 m; for power supply, trigger and RS422;
screw connector and free cable ends
- Calibration final inspection / assembly instructions
- 2 Protective caps
- 2 Centering elements

11. Additional Information
Please refer to
- the enclosed online documentation,
- the “Status and Error Messages” and “Notes” sections in the scanCONTROL Config-
uration Tools operating instructions.
You will find details about the individual programs in the respective operating instruc-
tions or in the operating instructions of this sensor, Chap. 6.2.
You will find the operating instructions online at www.micro-epsilon.com.
www.micro-epsilon.com
MICRO-EPSILON Messtechnik GmbH & Co. KG
Koenigbacher Str. 15
94496 Ortenburg / Germany, Tel. [phone]
Your local contact: www.micro-epsilon.com/contact/worldwide/
X9771399.04-A012031HDR