Microscan MicroHAWK 98-9000077-01 User manual

P/N 83-9220129-02 Rev B
MicroHAWK Accessory Guide
This guide contains instructions for how to install the following accessories on a MicroHAWK ID-20, ID-30,
or ID-40 Reader, or on a MicroHAWK MV-20, MV-30, or MV-40 Smart Camera:
• Kit, Diffuser, MicroHAWK ID-20/MV-20 (98-9000077-01)
• Kit, Polarizer, MicroHAWK ID-20/MV-20 (98-9000062-01)
• Kit, Window Replacement, MicroHAWK ID-30 and ID-40/MV-30 and MV-40 (98-9000051-01)
• Kit, Red LEDs, MicroHAWK ID-30 and ID-40/MV-30 and MV-40 (98-9000045-01)
• Kit, White LEDs, MicroHAWK ID-30 and ID-40/MV-30 and MV-40 (98-9000046-01)
MicroHAWK ID-20/MV-20
Diffuser Kit Hardware, MicroHAWK ID-20/MV-20
Diffuser Kit Installation, MicroHAWK ID-20/MV-20
Step 1: Peel the protective liner from the adhesive on the diffuser.
Step 2: Rest the narrow edge of the diffuser on the bottom edge of the window opening at an angle as
shown below.
Step 3: Center the diffuser left-to-right in the window opening.
Step 4: Affix the diffuser to the window.
Step 5: Run your finger over the surface of the diffuser using light pressure to complete the bond.
Qty. Description Part Number
1Kit, Diffuser, MicroHAWK ID-20/MV-20 98-9000077-01
Step 1
Step 3
Step 2
Steps 4 and 5
Peel Protective Liner
Narrow Edge Bottom Edge of
Window Opening
Diffuser Centered
(Equal Gaps)

2Copyright ©2017Microscan Systems, Inc.
MicroHAWK Accessory Guide
Polarizer Kit Hardware, MicroHAWK ID-20/MV-20
Polarizer Kit Installation, MicroHAWK ID-20/MV-20
Step 1: Peel the protective liner from adhesive on the polarizer.
Step 2: Rest the narrow edge of the polarizer on the bottom edge of the window opening at an angle as
shown below.
Step 3: Center the polarizer left-to-right in the window opening.
Step 4: Affix the polarizer to the window.
Step 5: Run your finger over the surface of the polarizer using light pressure to complete the bond.
Qty. Description Part Number
1Kit, Polarizer, MicroHAWK ID-20/MV-20 98-9000062-01
Step 1
Step 3
Step 2
Steps 4 and 5
Peel Protective Liner
Narrow Edge Bottom Edge of
Window Opening
Polarizer Centered
(Equal Gaps)

3Copyright ©2017Microscan Systems, Inc.
MicroHAWK Accessory Guide
MicroHAWK ID-30/MV-30 and ID-40/MV-40
Window Replacement Kit Hardware, MicroHAWK ID-30/MV-30 and ID-40/MV-40
LED Kit Hardware, MicroHAWK ID-30/MV-30 and ID-40/MV-40
Window Removal, MicroHAWK ID-30/MV-30 and ID-40/MV-40
Step 1: Disconnect power from the reader.
Step 2: Remove the four screws from the front window of the reader.
Step 3: Remove the front window and gasket.
Note: If installing a window accessory only, skip to Step 8.
Qty. Description Part Number
1Window or Window Accessory (included)
98-9000051-0140-80 Phillips-Head Screws (included)
1Gasket (included)
1Phillips Torque Wrench (not included) N/A
Qty. Description Part Number
2LED Boards (included) 98-9000045-01 (Red)
60-80 Phillips-head Screws (included) or
1Gasket (included) 98-9000046-01 (White)
1Phillips Torque Wrench (not included) N/A
1Fine-Tip Tweezers (not included)
Steps 2 and 3

4Copyright ©2017Microscan Systems, Inc.
MicroHAWK Accessory Guide
Outer LED Removal, MicroHAWK ID-30/MV-30 and ID-40/MV-40
Note: If installing an LED accessory only, skip to Step 6.
Step 4: Remove the two screws from the LED boards.
Step 5: Unplug the LED boards from the reader.
Note: The LED boards have a connector interface. Gently pry the top of each LED board from the main
board using fine-tipped tweezers or an equivalent tool. Use caution not to contact the LEDs as they may
become damaged.
Outer LED Installation, MicroHAWK ID-30/MV-30 and ID-40/MV-40
Step 6: Plug the LED boards into the main board. Use caution not to touch the LEDs, as they may be
damaged by contact.
Step 7: Secure the LED boards in place using the screws provided. Do not over-tighten the screws.
(1.0 in./lbs. (0.11 nm max.)
Steps 4 and 5
Steps 6 and 7

5Copyright ©2017Microscan Systems, Inc.
MicroHAWK Accessory Guide
Window Installation, MicroHAWK ID-30/MV-30 and ID-40/MV-40
Step 8: Install the gasket onto the reader. Ensure that the gasket is properly seated in place and is
covering all sealing surfaces.
Step 9: Install the window (or window accessory) onto the reader.
Step 10: Secure the window in place using the screws provided. Do not over-tighten the screws.
(1.0 in./lbs. (0.11 nm max.)
Steps 8, 9, and 10