Microsound TS631 User manual

TS631
Reworded 13 November 2013 Page 1 of 4
MICROSOUND
AC/DC Modified TS631 Manual
Step-by-Step Directions for programming TS631 Time Switch
Power On - Time Switch goes into time mode displaying Microsound TS631, the current day and time.
WHEN PROGRAMMING IS FINISHED, THE TIME SWITCH MUST BE IN THIS MODE.
To ring the bell manually, press Bwhile in this mode
D Changes to the next mode
#Changes back to the last mode
Please Note that it is normal for the unit to loose +/- 60seconds over a month or two. To adjust the current time,
please go to step No. J below. <<TIP: Use Telkom’s time line Tel: 1026 to get exact time>>
A. ENTER NEW ALARM (To set the alarm time i.e. when the bell/siren must be triggered)
1. Press D once to go into “Enter new alarm” mode.
2. Press * once to start programming the alarm times
3. Press: 1 for Monday / 2 for Tuesday / 3 for Wednesday /
4 for Thursday / 5 for Friday / 6 for Saturday / 7 for Sunday,
the cursor will then jump over to the zeros.
4. Enter time in 24 hour format hours 00: minutes :00: seconds :00
Note: Seconds must always be 00
E.g. 0 7 :4 5 :0 0 or 1 2 :0 0 :0 0 .
5. Press A to accept your new alarm. To clear an alarm time, press C .
6. Display will again show: Mon 00:00:00
7. Continue entering your alarms. When finished press D or # .
B. VIEW ALARMS (To check the alarms that have been programmed)
1. Press * to view the times that have been programmed.
2. Press B to move forward to the next time. This can be done until the display shows “No more
Alarms”. To move back through alarms press A .
3. To delete only a selected alarm, press C while the alarm is shown on the display. The display will
show the next alarm.
4. Press # to go back to the time mode or D to go to the next mode

TS631
Reworded 13 November 2013 Page 2 of 4
C. COPY ALARMS (If days have the same alarm times they can be copied)
1. Press *to enter programming mode.
2. With the cursor over the first Mon, press 1 –7 (numerals representing the day of the week) to select
the day which you want to copy.
3. The cursor will jump to the next Mon, press the numeral representing the day you want to have the
same alarms copied to.
4. Press A to accept your choice. Display will say “Copying…” until done. It will then revert back to the
menu.
5. Only copies a single day to another, one at a time.
6. Press # to go back to the time mode or D to go to the next mode
D. CLEAR ALARMS (BEWARE: This clears ALL alarms)
1. Press * to delete all the alarms on the time switch. (Note: to delete only one alarm, see “View alarms”
above)
2. Press # to go back to the time mode or D to go to the next mode
E. ALARM DURATION (how many seconds alarm will sound)
1. Press *to change the time in seconds that the alarm will sound. There will be no effect when the
Alarm mode is on “Latching”
2. Enter the time in seconds and press A to accept or C to clear the display.
3. The time switch will revert back to time mode.
F. ALARM MODE (Note: Latching will ring continuously)
1. Pressing A when this option appears will alternate between “Pulsed” and “Latching”. Pulse mode
must always be selected to trigger Bells, Sirens, or the SLSI80 / M20 intercoms.
2. Press #to go back to the time mode or D to go to the next mode
G. CONFIG MODE
1. Enables beep when any button is pressed. Press A to alternate between “on” and “off”.
2. Press # to go back to the time mode or D to go to the next mode
H. ARM ALARM (Switch on/off)
1. Press A to alternate between “on” or “off”. When “On” alarms will ring as programmed. When “Off”
all alarms will be disabled.
2. Press # to go back to the time mode or D to go to the next mode

TS631
Reworded 13 November 2013 Page 4 of 4
M20 (Pcb inside Psu box):
Normally closed
A Normally open
B Common
+ Positive
- Negative
AC/DC Earth
NB: The two relays always operate together.
Manufactured by:
Microsound Systems cc
P.O. Box 38220
Booysens
2016
Phone [phone]
Fax [phone]
Web www.microsound.co.za