Microtek ScanMaker i460 Instruction Manual

1
Step 2: Install Software
Step 1: Unpack Contents
Start Here
Installing your Microtek ScanMaker i460
Unpack your scanner package and check for
major components.
1. ScanMaker i460 scanner
2. Power adapter
3. Software CDs/DVDs
4. Hi-Speed USB cable
5. LightLid 35 IV*
Important: Do not remove the yellow stickers from your
scanner until you are told to do so. You must install software
before connecting your scanner.
Always close any open programs and turn off Anti-virus
utilities before installing software.
Copyright © 2013 Microtek International, Inc. http://www.microtek.com
I49-004750 B, September 2013
* The LightLid 35 IV is either as a standard equipment or an
optional accessory depending on the scanner configuration that
you purchased.
1
2
3
4
5
PC:
A. Place the Microtek Software CD/DVD
into a drive, and follow the on-screen
instructions to install the scanner
driver and software.
B. Restart your computer at the end of
all software installation.
NOTE: If the Microtek Software Installer screen does
not come up automatically, double-click the
following in succession: “My Computer”; the CD/
DVD-ROM icon; then cdsetup.exe to start the
installer program.
MAC:
A. Place the Microtek Software CD/DVD
(ScanPotter) into a drive, and double-click
the ScanPotter installer icon to install
ScanPotter.
B. Install the remaining software
components, then restart your computer
at the end of all software installation.
NOTE: After rebooting your Macintosh, the Microtek
software will attempt to locate your scanner on the
system. Since this is your first install and you have not
yet connected the scanner, simply ignore the message
that appears and proceed to the next step.

2
Step 3: Unlock Scanner
NOTE: To lock the scanner (for shipping and other reasons), tilt the scanner and look for the locking
switch on the left corner at the back, then push the locking switch to the "Locked" position. DO
NOT turn the scanner upside down when attempting to lock the unit.
B
C
A. Remove the yellow “Step 3” sticker
from your scanner.
B. With the scanner power off, tilt the
back left corner of the scanner to see
the locking switch at the bottom.
C. Push the locking switch to the position
as indicated in the graphic, with the
icon on the lock showing as
“Unlocked”.
Step 4: Connect Scanner
To the power adapter
A. Remove the yellow “Step 4” sticker from your scanner.
B. Connect the power adapter to the back of the scanner.
C. Plug the power adapter into a power source.
Unlocked Locked

3
To the Hi-Speed USB cable
D. Connect one end of the cable to your computer.
E. Connect the other end of the cable to the scanner.
D
E
Step 4: Connect Scanner (cont.)
F. Press and hold the Power button ( ) on
the button panel for a while. Once the
scanner is detected by your system,
the LED (green) will brighten, and the
scanner is ready to scan.
WEB
PDF
OCR
COPY
SCAN
POWER
E-MAIL
Scanner Buttons
The ScanMaker i460 is equipped with six scanner buttons, providing quick access to the
most frequently used functions. These buttons are WEB, PDF,OCR,E-mail, Copy, and
Scan.
WEB: Scans the image and directly links to your assigned photo-sharing
website.
PDF: Scans the image and saves it in the Adobe Acrobat PDF format.
OCR: Scans a text document, converts, and saves it in text file format.
Files may be immediately edited if configured in the MSC utility.
E-mail: Scans the image and delivers it directly to your e-mail editor.
Copy: Scans the image and sends it to your printer.
Scan: Captures images that can be saved as files or sent to an image-
editing application.
E-mail
Copy
OCR
PDF
Power
WEB
PDF
OCR
COPY
SCAN
POWER
E-MAIL
IV
POWER
WEB
Scan
LED (orange)
LED (green)

4
Using the LightLid 35 IV
NOTE: If your scanner configuration does not contain the LightLid 35 IV and you do not have
intention to use this device, please ignore this section.
Connecting the LightLid 35 IV
1. Remove the scanner lid.
2. Ensure that the scanner is powered off;
then plug the connector of the LightLid
into the scanner’s 9-pin accessory port.
To load film
A. To load filmstrips:
Turn the LightLid 35 IV over. Load the
filmstrip inside the upper slot of the
LightLid, with the film’s shiny base
facing up.
B. To load slides:
Turn the LightLid 35 IV over. Load the
slide inside the lower slot of the LightLid,
with the slide facing up.
Do not block
calibration window Do not block
calibration window
To place the LightLid 35 IV
Place the LightLid 35 IV with the loaded film vertically on the scan bed. The LightLid
should be flush against the top ruler of the bed, with the slot running down the center.
Align the top of the LightLid with
the recessed area, as label “Place
LightLid 35 IV Here”.
WEB
PDF
OCR
COPY
SCAN
POWER
E-MAIL
WEB
PDF
OCR
IV

5
Basic Scanning for PC Users
WEB
PDF
OCR
COPY
SCAN
POWER
E-MAIL
IV
Scanning Photos
1. Place the photo.
To scan a photo, place the photo on the scanner
bed. The top end of the original should be positioned
towards the right of the scanner, with the surface to
be scanned facing down.
2. Launch ScanWizard EZ.
To launch ScanWizard EZ as a stand-alone program, double-click
the ScanWizard EZ icon on your desktop. When ScanWizard EZ is
launched for the first time, the control panel of ScanWizard EZ -
EZ Mode appears automatically.
3. Scan your material.
Click the Scan button on the control panel of EZ Mode to start scanning.
The ScanWizard EZ will detect the photo on the scanner glass surface first, next
automatically calibrate the scanner, crop the image, and finally perform the image
scan with factory settings. When done, the scanned image can be saved in a file and
delivered to the specified location.
Press the Scan
button to start
scanning
Switches to
the Professional Mode
Switches to
the Advanced Mode
Activates
the Preferences window
Minimizes ScanWizard EZ
Exits ScanWizard EZ
Select preferences if necessary
Before you start scanning, specify image settings related to your output image in
the Preferences window according to your preferences.
Auto Settings – Switches on/off Auto-crop and Auto-deskew, and applies ACE
(Automatic Color Enhancement) to the image.
Scan Mode – Sets the image resolution and scan quality to match your target
application.
Save – Assigns the folder location, a file name, and the file format for the output
image.Also, it allows you to specify an application to open the image.
Theme – Changes the appearance of the control panel for the EZ mode.
NOTE: For details about how to use the ScanWizard EZ‘s Advanced Mode and
Professional Mode, refer to the ScanMaker i460 Supplement.

6
Scanning Film
1. Place the film.
To scan film, use the LightLid 35 IV. Refer to “Using the LightLid 35 IV” in this guide
to load film.
2. Launch ScanWizard EZ.
Follow the step 2 in “Scanning Photos” on previous page to launch ScanWizard EZ.
3. Switch to ScanWizard EZ - Professional Mode.
Click the Professional Mode button on the control panel of the EZ Mode to switch to
the Professional Mode.
4. In the Preview window of the Professional Mode, click the Scan Material button to
choose Negative Film for negatives; choose Positive Film for transparencies and slides,
depending on the film type you are using.
5. Click the Overview button to perform a preliminary scan of the film loaded onto the
scanner.
6. Select the Scan Frame tool, and choose the area to be scanned by sizing the marquee
around the targeted area.
7. Specify your scanning requirements in the Settings window. Choose the desired image
type and resolution, and adjust the scan frame settings if necessary.
8. Adjust image quality if necessary, using the Advanced Image Correction tools.
9. Click the Scan to button in the Preview window to scan the film.
Scan Job Queue
window
Press to switch to
ScanWizard EZ - EZ Mode
Preview window
Settings window
Press to switch to
ScanWizard EZ - Advanced
Mode
Click NEW to create
more scan frames

7
Basic Scanning for Mac Users
1. Place the scan material.
•To scan photos, place the photo to be scanned on the scan bed, as detailed in the
“Basic Scanning for PC Users” section in this guide.
•To scan film, use the LightLid 35 IV, as detailed in the “Using the LightLid 35 IV”
section in this guide.
2. Launch ScanPotter as a stand-alone by clicking on the program icon, or by selecting it
from the application folder in your Mac OS X system.
3. In the Scan Source options menu, depending on the scan material you are using,
choose either Reflective for photos, Negative Film for negatives, or Positive Film for
transparencies and slides.
4. Specify your scanning requirements in the Scanner Settings column.
a) Select the appropriate image type (e.g., RGB Color) in the Color Type as your
image output type.
- Select Color to scan the image in color.
- Select Grayscale to scan the image in grayscale.
- Select Black & White to scan the image in black-and-white.
b) Select a desired resolution in the Resolution for your image output resolution.
c) Select Automatic Detection or a desired dimension in the Scan Frame as your
preview image size.
5. Click the Preview button to perform a preliminary scan of the image in the Preview
window.
6. If necessary, resize the scan frame (floating dotted rectangle) around the image by
dragging on the square spots on the edge or on the corner of the scan frame to
determine the final size of the actual scan.
7. If necessary, specify file settings for your output image files, using the options offered
in the File Saving Settings column.
8. If necessary, click the Image Settings button to switch to a window in which you can
select a preset image effect to the image directly or adjust image quality manually by
using the additional image correction tools.
9. Click the Scan button to start scanning.
NOTE: For details on scanning photos and film, see the ScanMaker i460 Supplement in the Microtek
Software CD/DVD.

8
Click the Image Settings
button to switch to a
window where contains a
composite display of nine-
image-effects (Filter
column) and additional
image correction tools
(Additional Adjustment
column) for your scanned
image.
Click the Scan Settings button
to switch back to the default
control panel of ScanPotter
Scan frame
(enclosed by dotted lines)
Preview window when
scanning slides
Preview
window when
scanning
photos

9
Problems?
The LEDs on the button panel indicate the status of the scanner.
If you encounter any problems, check the section below and follow the suggested solution if your
problem is listed. You may also want to go over installation steps 1 to 4 of this “Start Here”
document to make sure that you have followed all procedures properly.
1. No light comes on when the scanner is turned on.
Make sure your scanner is connected to your computer and plugged into a power source.
Make sure your scanner is detected by your computer.
2. Add/Remove Hardware Wizard appears on your screen.
Click the “Cancel” button and close the control panel. Disconnect the USB cable from the back of
your computer, and refer to the installation instructions in this guide.
3. When trying to scan, an error message appears on your screen that reads, “Can’t Find Scanners”.
Make sure your scanner is unlocked (see Step 3).
Make sure your scanner is connected to your computer and plugged in to a power source
(see Step 4).
Uninstall and reinstall the ScanWizard EZ or ScanPotter software.
4. After clicking scan, a blank screen appears.
Make sure your scanner is unlocked (see Step 3).
Uninstall and reinstall the ScanWizard EZ or ScanPotter software.
5. Having trouble scanning negatives or slides?
Make sure the LightLid 35 IV is properly installed, with its connector securely connected to the
scanner’s 9-pin accessory port.
Make sure you place the LightLid 35 IV with the film loaded properly on the scan bed. Do not block
the calibration area (as indicated in the “Using the LightLid 35 IV” section).
From the ScanWizard EZ - Professional Mode, go to the Preview window, then click the Scan
Material button to select either the Positive Film or Negative Film option.
From the ScanPotter, go to the Scanner Settings column, then click the Scan Source drop-down
menu to select either the Positive Film or Negative Film option.
Uninstall and reinstall the ScanWizard EZ or ScanPotter software.
WEB
PDF
OCR
COPY
SCAN
POWER
E-MAIL
IV
On - Scanner is on
LED (orange)
LED (green)
Both on - Ready to scan
Flashing - Scanning or error happened
Off - Scanner is off

10
DoYou Need Assistance?
Manuals
If you have additional questions and need further instruction or information, we provide
electronic manuals for:
1. Using your ScanMaker i460 (Supplementary information)
2. Using the ScanWizard EZ or ScanPotter scanning software
3. Using the bundled third-party software
To access the electronic manuals: Insert the scanner’s software CD/DVD into your
computer’s CD/DVD-ROM drive. Next, locate and click the “Manuals” option when the
software installer window appears on your screen. Finally, select and click the title of the
manual you wish to view.
Missing Items
If your package is missing items, please call the Microtek Customer Service Department.
Drivers & Software Upgrades
After you finish the installation of software, if you found that the installed drivers and
software cannot run your product or your computer system properly later, please go to
the Microtek Download Service site at ww7.microtek.com.tw/service.php to download
and install any updates you may require.
For additional information about Microtek products, please visit our website at
www.microtek.com.
Copyright © 2013 Microtek. Microtek, ScanMaker, ArtixScan,
ScanWizard and ColoRescue are trademarks or registered trademarks of
Microtek International, Inc. All other trademarks or registered
trademarks are the property of their respective holders. Specifications,
software and hardware bundles are subject to change without notice.
Delivery of technical support services subject to change without notice.
Not responsible for typographical errors.
Power Adapter
Use only power supplies (AC/DC adapters) listed below:
Voltage Manufacturer Model No.
100V to 240V WUXI HARD HDAD-120015-3C (U.S./TWN)
100V to 240V WUXI HARD HDAD-120015-3B (Europe)
100V to 240V WUXI HARD HDAD-120015-3D (AUS)
100V to 240V WUXI HARD HDAD-120015-3E (UK)
NOTE: Please make sure that the electrical outlet to where the scanner will be
connected is nearby and readily accessible.