Microtek XT5750 HS User manual

1
Step 2: Install Software
Step 1: Unpack Contents
Start Here
Installing your Microtek XT5750 HS
Unpack your scanner package and check for
major components.
1. XT5750 HS Scanner
2. Power adapter
3. Hi-Speed USB cable
4. Software CDs/DVDs
5. Start Here guide
Important:You must install software before
connecting your scanner.
Always close any open programs and turn off Anti-
virus utilities before installing software.
Copyright © 2021 Microtek International, Inc. https://www.microtek.com
I49-005389 A, March 2021
A. Turn on your computer.
B. Place the Microtek Software CD/DVD into a drive, and follow the on-screen
instructions to install the scanner driver and software.
C. Restart your computer at the end of all software installation.
NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the
following in succession: “My Computer”; the CD/DVD-ROM icon; then cdsetup.exe to start the
installer program.
3
1
5
4
2

2
Connect Scanner
To the power adapter
A. Connect one end of the power adapter to the back of the scanner.
B. Plug the other end of the
power adapter into a wall outlet or
other power source.
To the Hi-Speed USB cable
C. Connect one end of the Hi-Speed USB cable to your computer.
D. Connect the other end of
the Hi-Speed USB cable to the
scanner’s USB port.
A
B
E
C
D
E. Press and hold the Power button ( ) until the
POWER indicator becomes blue.
Once the system detects the scanner, the
scanner is ready to scan.

3
Customize the Function Buttons
The XT5750 HS scanner is equipped with 4 physical function buttons that can be
customized to automate a number of predened operations, such as scanning to a le,
sending an image to your printer or e-mail account, scanning for OCR, etc. Customizing
is done through the Scanner Button Settings interface in the ScanWizard DI, refer to the
scanner’s User’s Manual for more details.
4 programmable
function buttons
Positioning Documents
1. Raise the scanner lid.
2. Pplace the document to be scanned face down on the glass surface of the scanner.
3. Lower the scanner lid.
Position a book or a bound document:
Align the spine or inner edge of the book with the
arrow icon ( ) located at the lower right corner of the
scan bed and along the dotted line shown as picture.
If necessary, lift the scanner lid straight up or remove
it from the hinges when scanning a thick book.
Position a single-sheet document:
Align the top corner of the document with the arrow
mark ( ) located at the upper-right corner of the scan
bed, with its edges rmly against the rulers.
F4
F3
F2
F1

4
Scanning Documents
1. Place the document to be scanned facing down on the scanner’s glass surface.
2. Launch ScanWizard DI as a stand-alone program by clicking on the ScanWizard DI icon
on the desktop.
3. Click the Scan Setup button in the interface to activate the Scan Setup interface.
4. In the Scan Setup interface, follow the steps below to specify your basic settings.
a) Select Flatbed in the Scan Source as your image
input device.
b) Select the appropriate image type in the Color
Mode as your image output type.
c) Select a dimension in the Paper Size as your
preview image size.
d) Select a desired resolution in the Resolution for
your image output resolution.
e) If necessary, select “Text Orientation Recognition”
in the Rotate to ensure the scanned images in
a readable orientation. When it is selected, you
can select the preferred language used as an
identication in the options menu.
f) If “Auto-crop” & “Auto-deskew” are selected,
the scanner automatically detects the size of the
original image, crops the full scan frame to t the
image, and removes unwanted black borders after
the scan, as well as corrects the distorted image
for proper alignment.

5
5. Click the Show Preview Window and Show Setting Window tabs in the Scan Setup
interface to display other interfaces which are helpful for your scanning processing.
6. Click the Preview button to perform a preliminary view of the entire image. When
done, a preview image appears in the Preview window.
7. Go to the “General” panel by clicking the General tab in the Settings window. Specify
the settings for your requirements there.
a) Select the image type in the Document Type as your input image type.
– Select Photo to scan color prints.
– Select Text to scan text.
b) If necessary, check “Remove Blank Page” and
“Remove Punch Hole” to enhance the quality of the scanned images.
8. If necessary, go to the “Image Process” panel by clicking the Image Process tab in the
Settings window.
Use the image correction tools presented there to enhance the image quality according
to your specic requirements.
9. Click the OK button to close the Scan Setup interface and return to the Main interface
of ScanWizard DI.
10. In the Main interface, click the File Format menu button to select a le format for the
scanned images.
11. In the Main interface, click the File Name menu button to specify a le naming method
for the scanned images.
12. In the Main interface, click the Normal Scan button to start scanning.
When done, the scanned images will be automatically saved into the folder dened in
the File Location menu box. At the same time, the scanned images will be displayed
in thumbnail sizes in the Thumbnail View window and labeled with the le name and
le format specied earlier.
13. Click the Open Folder button to locate the scanned images if you want to view.
NOTE: For more details on other scanning scenarios applicable to your scanner, refer to the scanner’s
User’s Manual in the Microtek Software CD/DVD.

6
AP control panel (Main interface)
File Location
menu box
Click on a
thumbnail image
to enlarge it in
the Image View
Window at the
right side of the
interface.
TWAIN driver control panel (Scan Setup interface)

7
Problems?
The LED indicators on the button panel of the scanner indicate different states of the
scanner. The POWER indicator stands for power and should always stay on steady when
the scanner is on.
First, make sure that you have followed Steps 1 to 3 as described in this guide (unpack,
install, connect). Then if your problem is listed here, try the suggested solution.
1. No light comes on when the scanner is turned on.
Make sure your scanner is connected to your computer and plugged into a power
source.
Press and hold the Power button until the POWER indicator becomes blue.
2. The Add/Remove Hardware Wizard appears on your screen.
Click the “Cancel” button and close the ScanWizard DI software.
Disconnect the USB cable from your computer, and refer to the installation instructions
in this guide or the scanner's User’s Manual.
3. When trying to scan, an error message appears on your screen that reads, “Can’t Find
Scanners”.
Make sure your scanner is connected to your computer and plugged in to a power
source.
Uninstall and reinstall the ScanWizard DI software.
4. When trying to scan, an error message “Code: -1000, No response from
scanner”appears on your screen.
Make sure that the POWER indicator has become blue. If not, press and hold the
Power button until the POWER indicator becomes blue.
5. After clicking scan, a blank screen appears.
Uninstall and reinstall the ScanWizard DI software.
SCAN indicator
(Green)
POWER indicator
(Blue)
Blue On - Ready to scan
Green Flashing - Scanning
Red On - Error
All Off - Scanner is off

8
DoYou Need Assistance?
Manuals
If you have additional questions and need further instruction or information, we provide
electronic manuals for:
1. Using your XT5750 HS Scanner (User’s Manual)
2. Using the ScanWizard DI scanning software (Reference Manual)
To access the electronic manuals: Insert the scanner’s software CD/DVD into your
computer’s CD/DVD-ROM drive. Next, locate and click the “Manuals” option when the
software installer window appears on your screen. Finally, select and click the title of the
manual you wish to view.
Missing Items
If your package is missing items, please call the Microtek Customer Service Department.
Drivers & Software Upgrades
After you nish the installation of software, if you found that the installed drivers and
software cannot run your product or your computer system properly later, please go to the
Microtek Download Service site at microtek.com/en/download to download and install any
updates you may require.
For additional information about Microtek products, please visit our website at www.
microtek.com.
Copyright © 2021 Microtek. Microtek, ScanMaker, ArtixScan, ScanWizard and
ColoRescue are trademarks or registered trademarks of Microtek International,
Inc. All other trademarks or registered trademarks are the property of their
respective holders. Specications, software and hardware bundles are subject to
change without notice. Delivery of technical support services subject to change
without notice. Not responsible for typographical errors.
Power Adapter
Use only power supplies (AC/DC adapters) listed below:
Voltage Manufacturer Model No.
AC100V to 240V KUANTEN KT241120200EU
AC100V to 240V KUANTEN KT241120200US
NOTE: Please make sure that the electrical outlet to where the scanner will be
connected is nearby and readily accessible.