Middle Atlantic Products UQFP-2D User manual

• Quiet operation, 27dB at full speed for 4 fan models, 24dB at
full speed for 2 fan models
• Overtemp and fan failure notification
• 100 CFM in 4 fan units, 50 CFM in 2 fan units
• Available with commercial and designer inspired aesthetic treatments
• Fan speeds proportional to temperature of enclosure to extend fan life,
reduce dust and maintenance
• Temperature probe with 9’ cord and wire ties included
• Compact design occupies only 2 rackspaces
The UQFP Series Ultra Quiet Fan Panel provides smart cooling and
monitoring where fan noise is not an option
Model
#s UQFP-22, UQFP-44
EIA compliant 19" Ultra Quiet Fan Panel shall be Middle Atlantic Products model #
UQFP-__(2,4). Panel shall be constructed of 16-gauge steel, finished in a durable black
powdercoat and shall occupy 2 rackspaces. Fans shall activate at 80°F (27°C), reach full
speed at 90°F (32°C) and switch off at 77°F (25°C). Fans shall displace __CFM (50,100)
with a maximum decibel level of __ (24,27) dB (measurements made 1 meter from
source, centered horizontally and vertically). Panel shall provide local status notification of
power (green LED), fan speed (yellow LED) and overtemp (red LED). Fan LED light shall
blink relative to fan speed. Rear, normally open dry switch closure shall provide overtemp
alarm signal to compatible, customer supplied monitoring device. Fan panel shall be
warrantied to be free from defects in materials and workmanship under normal use and
conditions for a period of 3 years. Panel shall include a UL Listed 12V DC power supply
and temperature probe with a 9' cord.
Model
#s UQFP-44DRA, UQFP-44DRC (Designer Inspired)
Designer Inspired Ultra Quiet Fan Panel with smoked lens front display shall be
Middle Atlantic Products model # UQFP-4DRX (X = finish, refer to chart). Overtemp
alarm set point shall be user definable from 95°-115°F (35°-46°C). Overtemp alarm
output shall be normally open dry contact closure for use with customer supplied
monitoring system. Fans shall activate at 80°F (27°C) and operate at speeds proportional
to temperature inside enclosure. Fans shall displace 100 CFM with a maximum decibel
level of 27dB (measurements made 1 meter from source, centered horizontally and
vertically). Fan panel shall occupy two rackspaces. Chassis shall be constructed of 20-gauge
steel with 16-gauge aluminum face. Fan panel shall provide local sensor fault notification.
Fan panel shall be warrantied to be free from defects in materials and workmanship
under normal use and conditions for a period of 3 years. Panel shall include a UL
Listed 12V DC power supply and temperature probe with a 9' cord.
Model
#s UQFP-22D,
UQFP-44D (with display)
EIA compliant 19" Ultra Quiet Fan Panel with local notification display shall be
Middle Atlantic Products model # UQFP-__(2,4)D. Panel shall be constructed of 16-gauge
steel, finished in a durable black powdercoat and shall occupy 2 rackspaces. Fans shall
activate at 80°F (27°C), reach full speed at 90°F (32°C) and switch off at 77°F (25°C). Fans
shall displace __CFM (50,100) with a maximum decibel level of __ (24,27) dB
(measurements made 1 meter from source, centered horizontally and vertically). Panel
shall provide local status notification of power (green LED), fan speed (yellow LED) and
overtemp (red LED). Fan LED light shall blink relative to fan speed. Rear, normally open
dry switch closure shall provide overtemp alarm signal to compatible, customer supplied
monitoring device. Overtemp alarm set point shall be user definable from 95°-115°F
(35°-46°C). Front display shall provide notification of overtemp and fan fault conditions.
Rear, normally open dry switch closure shall provide fan fault alarm signal to compatible,
customer supplied monitoring device. Alarm set point button shall control Fahrenheit/
Celsius setting and overtemp alarm threshold in 1-degree increments. Fan panel shall be
warrantied to be free from defects in materials and workmanship under normal use and
conditions for a period of 3 years. Panel shall include a UL Listed 12V DC power supply and
temperature probe with a 9' cord.
96-01037 / rev 1 / 10-19-05
96-01037 / rev 1 / 10-19-05 / UQFP Series
UQFP-4D
Features
Architects’ and Engineers’ Specifications
UQFP Series
Ultra Quiet Fan Panels
Engineered Mounting Solutions
electronic version available at middleatlantic.com
middleatlantic.com
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: [phone] • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: [phone] • middleatlantic.ca
Middle Atlantic Products, Inc.
EIA Compliant
UQFP-4DRA
UQFP-4
UQFP-4DRC

OVER
TEMP
ALARM
(N.O.)
12VDC
1A
FAN
FAULT
ALARM
(N.O.)
CONTROLSETTINGS
Pressonce to view the current
overtempalarm setting.
Eachadditional push will raise
theovertemp alarm setting
by1O.
Totoggle between Fahrenheit
andCelsius, press and hold for
3seconds.
PUSH
Temperature
Probe
Probe
Linearization
Processor
A/D
Converter
Alarm
SetInput
SPI
Interface
Microcontroller
FanFault
Input
PulseWidth
Modulation
Alarm
Output
AlarmSet
Interface
Temperature
Display
FanDrive
Processor
Fan
Rotation
Sensor
FanFault
Processor
DryContact
Outputs
FanFault
AlarmOutput
Overtemp
AlarmOutput
UQFP Series basic dimensions
Middle Atlantic Products, Inc.
3.33
[85]
19.00 [483]
3.49 [89]
2 rack spaces
power LED (green)
fan LED (yellow)
over temp LED (red)
Display (UQFP-2D, UQFP-4D)
fan
fault alarm output
overtemp alarm output
12 VDC input jack
9’ temperature
alarm set
point
button
(UQFP-2D,
UQFP-4D)
2.74
.21
[5] .46
[12]
SIDE VIEW
REAR VIEW
FRONT VIEW
TOP VIEW
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: [phone] • middleatlantic.com
Part # # of Fans
Overtemp Notification User
Definable
Overtemp
Setting
Fan Failure
Notification
Local & Remote
Display
Current Draw
at 12 Volts DC Airflow dB
level at Finish
Local LED Local Display Remote
UQFP-2D 2 iiii i 310 mA 50 CFM 24 dB Black Powdercoat
UQFP-4D 4 iiii i 560 mA 100 CFM 27 dB i
UQFP-2 2 iiii i 270 mA 50 CFM 24 dB i
4iiii i i
UQFP-4D shown
All dimensions in
inches
[Bracketed dimen-
Temperature
Probe
Probe
Linearization
Processor
A/D
Converter
Alarm
Set Input
SPI
Interface
Microcontroller
Fan Fault
Input
Pulse Width
Modulation
Alarm
Output
Alarm Set
Interface
Temperature
Display
Fan Drive
Processor
Fan
Rotation
Sensor
Fan Fault
Processor
Dry Contact
Outputs
Fan Fault
Alarm Output
Overtemp
Alarm Output
TOP
2.89 [73]
3.49 [89]
2 RACK SPACES
9’ TEMPERATURE PROBE
OVER
TEMP
ALARM
(N.O.)
12VDC
1A
FAN
FAULT
ALARM
(N.O.)
CONTROL SETTINGS
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
by 1O.
To toggle between Fahrenheit
and Celsius, press and hold for
3 seconds.
PUSH
Temperature
Probe
Probe
Linearization
Processor
A/D
Converter
Alarm
Set Input
SPI
Interface
Microcontroller
Fan Fault
Input
Pulse Width
Modulation
Alarm
Output
Alarm Set
Interface
Temperature
Display
Fan Drive
Processor
Fan
Rotation
Sensor
Fan Fault
Processor
Dry Contact
Outputs
Fan Fault
Alarm Output
Overtemp
Alarm Output
UQFP Series basic dimensions
Middle Atlantic Products, Inc.
3.12 [79]
3.33
[85]
power LED (green)
fan LED (yellow)
over temp LED (red)
display (UQFP-2D, UQFP-4D)
overtemp alarm output
12 VDC input jack
2.74
[70]
.21
[5] .46
[12]
SIDE VIEW
REAR VIEW
FRONT VIEW
TOP VIEW
US: New Jersey • California • Illinois • Voice: 973-839-1011 Fax: [phone] • middleatlantic.com
Canada: Ontario • British Columbia • Voice: 613-836-2501 Fax: [phone] • middleatlantic.ca
Part # # of Fans
Overtemp Notification User
Definable
Overtemp
Setting
Fan Failure
Notification
Local & Remote
Display
Sensor Fault
Notification
Local
Current Draw
at 12 Volts DC
Airflow
at Full
Speed
dB
level at
Full
Speed Finish
Local LED Local Display Remote
UQFP-2D 2 iiii i 310 mA 50 CFM 24 dB Black Powdercoat
UQFP-4D 4 iiii i 560 mA 100 CFM 27 dB Black Powdercoat
UQFP-2 2 ii 270 mA 50 CFM 24 dB Black Powdercoat
UQFP-4 4 ii 510 mA 100 CFM 27 dB Black Powdercoat
UQFP-4DRA 4i i i i i 560 mA 100 CFM 27 dB Black brushed anodized
UQFP-4DRC 4i i i i i 560 mA 100 CFM 27 dB Silver brushed anodized
CONTROL SETTINGS
Pressonce to view the current
overtempalarm setting.
Eachadditional push will raise
theovertemp alarm setting
by1O.
Totoggle between Fahrenheit
andCelsius, press and hold for
3seconds.
PUSH
OVER
TEMP
ALARM
(N.O.)
12VDC
1A
FAN
FAULT
ALARM
(N.O.)
Temperature
Probe
Probe
Linearization
Processor
A/D
Converter
Alarm
Set Input
SPI
Interface
Microcontroller
Fan Fault
Input
Pulse Width
Modulation
Alarm
Output
Alarm Set
Interface
Temperature
Display
Fan Drive
Processor
Fan
Rotation
Sensor
Fan Fault
Processor
Dry Contact
Outputs
Fan Fault
Alarm Output
Overtemp
Alarm Output
UQFP-4D
All dimensions in inches
[Bracketed dimensions in
millimeters]
SIDE VIEW
TOP VIEW
FRONT VIEW
REAR VIEW
2.89 [73]
3.33
[85]
19.00 [483]
3.49 [89]
2 rackspace
9’ temperature probe
alarm set
point
button
(UQFP-2D,
UQFP-4D)
fan fault alarm output
(UQFP-2D, UQFP-4D)
overtemp alarm output
12 VDC input jack
19.00
[483]
3.49 [89]
2 rackspaces
9’ temperature probe
2.70
[69] .46 [12]
fan fault alarm output
UQFP-4DRx
alarm set
point button
display