Middle Atlantic Products UQFP Series User manual

I-00467 Rev -
UQFP SERIES
Ultra Quiet Fan Panels
Instruction Sheet
THANK YOU
Thank you for purchasing the UQFP Series Ultra Quiet Fan Panel. Please read these instructions
thoroughly before installing this product.
PRODUCT FEATURES
- Reliable cooling with minimal noise
- Local and remote status notification
- On-board processor controls fan speed
proportional to enclosure temperature
(220V Models)

Page 2
SPECIFICATIONS
UQFP-2 & UQFP-2D/IUQFP-2 & IUQFP-2D
Current Draw: 270 mA @ 5V DC (UQFP-2/IUQFP-2) Airflow: 50 CFM @ Full Speed
310 mA @ 5V DC (UQFP-2D/IUQFP-2D) RPM: 1900 @ Full Speed
Noise: 24 dB @ Full Speed
UQFP-4 & UQFP-4D/IUQFP-4 & IUQFP-4D
Current Draw: 510 mA @ 5V DC (UQFP-4/IUQFP-4) Airflow: 100 CFM @ Full Speed
560 mA @ 5V DC (UQFP-4D/IUQFP-4D) RPM: 1900 @ Full Speed
Noise: 27 dB @ Full Speed
UQFP-2/IUQFP-2
UQFP-2D/IUQFP-2D
UQFP-4/IUQFP-4
UQFP-4D/IUQFP-4D

Page 3
FUNCTIONS
Models UQFP-2 & UQFP-4/IUQFP-2 & IUQFP-4
(UQFP-4 Model Shown)
POWER (GREEN): This LED indicates that the unit is receiving power.
FAN (YELLOW): When rack temperature reaches 81OF (27OC) this LED will begin to flash
indicating that the fans have turned on. It will continue flashing proportional to the fan speed,
as long as the fans are on.
OVERTEMP (RED): If rack temperature reaches 100OF (37OC) this LED will light indicating an
over temperature condition within the rack.
OVERTEMPALARM OUTPUT: This normally open dry contact closure will provide an alarm to an
external (remote) monitoring system if your enclosure reaches overtemp condition.
5V DC INPUT JACK: Power supply connector
TEMPERATURE PROBE: Remote temperature sensor. (9' long)
POWER (GREEN) FAN (YELLOW)
OVERTEMP (RED)
FRONT VIEW
OVER
TEMP
ALARM
(N.O.)
5VDC
2A
OVERTEMPALARM OUTPUT 5V DC INPUT JACK
TEMPERATURE PROBE
REAR VIEW
DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE.

Page 4
POWER (GREEN): This indicates that the unit is receiving power.
FAN (YELLOW): When rack temperature reaches 81OF (27OC), this LED will begin to flash indicating
that the fans have turned on. It will continue flashing proportional to the fan speed, as long as the fans
are on.
ALARM (RED): At the factory preset overtemp of 100OF (37OC), this LED will light indicating an over
temperature condition within the rack. See Alarm Set Point Button instructions below to change the
overtemp alarm setting.
DISPLAY: The display will indicate the rack temperature and provide a read-out of the following fault
codes during one of these conditions:
OVERTEMP: The temperature of the enclosure has risen above the alarm set point. Inspect
airflow intake and output for obstructions. Additional cooling capacity may be required.
FAN FAULT: One or more of the fans has stopped. Check all fans for obstruction.
If problem persists, call Technical Support at [phone].
Models UQFP-2D & UQFP-4D/IUQFP-2D & IUQFP-4D
(UQFP-4D Model Shown)
POWER (GREEN)
DISPLAY
FAN (YELLOW)
ALARM (RED)
FRONT VIEW

Page 5
CONTROL SETTINGS
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
by 1O.
To toggle between Fahrenheit
and Celsius, press and hold for
3 seconds.
PUSH
ALARM SET POINT BUTTON:
- To change display from Fahrenheit to Celsius, press and hold Alarm Set Point Button for 3 seconds.
- To view alarm set point, simply press and release the Alarm Set Point Button once.
- To change the factory preset alarm set point, repeatedly press the Alarm Set Point Button until
desired temperature is displayed. Factory preset overtemp alarm set point is 100OF (37OC).
Adjustment range is from 95Oto 115OF (35Oto 46OC)
FAN FAULT / OVERTEMPALARM OUTPUT:
These normally open dry contact closures will provide an alarm to an external (remote) monitoring
system if your enclosure experiences a fan fault or overtemp condition.
5V DC INPUT JACK: Power supply connector
TEMPERATURE PROBE: Remote temperature sensor (9' long).
FAN FAULTALARM OUTPUT 5V DC INPUT JACK
OVERTEMPALARM OUTPUT
TEMPERATURE PROBE
REAR VIEW
SIDE VIEW
ALARM SET POINT BUTTON
OVER
TEMP
ALARM
(N.O.)
5VDC
2A
FAN
FAULT
ALARM
(N.O.)
DO NOT OPEN. NO USER SERVICEABLE PARTS INSIDE.

Page 6
1) Route Temperature Probe, Alarm Output, and Power Supply wires along the rear of the
panel as shown above. Tie points are provided to route wires left or right. Do not allow wires
to interfere with fan operation.
2) Using tie saddle included, mount the temperature probe wire into highest available area inside
of rack. In order to achieve proper temperature sensing, the probe should be installed near
the top of the rack. The probe is provided with a generous 9' lead.
WIRE TIE HERE
WIRE TIE HERE
CONTROL SETTINGS
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
by 1
O
.
To toggle between Fahrenheit
and Celsius, press and hold for
3 seconds.
OVER
TEMP
ALARM
(N.O.)
5VDC
2A
FAN
FAULT
ALARM
(N.O.)
PUSH
CONTROL SETTINGS
Press once to view the current
overtemp alarm setting.
Each additional push will raise
the overtemp alarm setting
by 1
O
.
To toggle between Fahrenheit
and Celsius, press and hold for
3 seconds.
OVER
TEMP
ALARM
(N.O.)
5VDC
2A
FAN
FAULT
ALARM
(N.O.)
PUSH
TIE SADDLE TEMPERATURE PROBE
INSTALLATION
UQFP-2D (left) & UQFP-4D (right) Shown.
TECH TIP: Ensure that you have access to the rear of the panel to make connections and
configure settings once mounted. If access to rear of unit is limited, cable management and
setting configurations must be done prior to mounting the panel.
3) (220V models only) Select appropriate wall plug for your region and attach to
provided power supply. Connect power supply to power source.

Page 7
THERMAL MANAGEMENT GUIDELINES
- Mount fan panel in highest available location of enclosure.
- Use vent blockers to cover any vent at the top of side panels.
- Do not place vent panels within six rackspaces below fan panel. Cover any of these spaces.
- If heat producing equipment is in the middle of the rack, use a 3 space vent panel at
the bottom
- Use a 2 space vent panel if heat producing equipment is at the bottom of the enclosure.
UQFP-4D
(SHOWN)
VENT PANEL

Page 8
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the UQFP Series Ultra Quiet Fan Panels to be
free from defects in material or workmanship under normal use and conditions for a period of three (3)
years from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other parties) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of
and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products
purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this warranty
does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BYAPPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS)ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone]
International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
113 Iber Road - Ottawa, ON - K2S 1E7
Voice 613-836-2501 - Fax [phone]
middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
30% Recycled Paper