2
F-33G/F-43G: The unit plugs into the options
connector under the battery. Before plugging the
unit in, open jumper D to open the radio’s PTT path,
if common PTT is not being used.
F-120/220: The unit plugs into the options connector
located on the main board. Before installing the unit,
open the radio’s PTT path by opening the PTT
jumper on the front PC board located next to the
PTTI and PTTO pads. This jumper is listed as CP2
on the schematic of the radio. Only open the PTT
path if common PTT is not being used. This radio
uses a negative PTT; therefore, you will need to
open J1 on the ANI-F-IC1.
F-320/420/520/620: The unit plugs into the options
connector located on the main board. Before
installing the unit, open the radio’s PTT path by
opening PTT jumper C, if common PTT is not being
used. This radio uses a negative PTT; therefore,
you will need to open J1 on the ANI-F-IC1.
F-1020/2020: The unit plugs into the options
connector located on the main board. Before
installing the unit, open the radio’s PTT path by
opening jumper PTT, if common PTT is not being
used. This radio uses a negative PTT; therefore,
you will need to open J1 on the ANI-F-IC1.
F-1720/1820: The unit plugs into the options
connector located on the main board. Before
installing the unit, open the radio’s PTT path by
opening jumper PTT, if common PTT is not being
used. This radio uses a negative PTT; therefore, you
will need to open JU-1 on the ANI-F-IC1.
HARDWARE ALIGNMENT
For the TX Audio Output in a wide band system, set
the ANI modulation pot R12 to 3.3 KHz (66% of 5
KHz) of deviation per EIA specifications. For the TX
Audio Output in a narrow band system, set the ANI
modulation pot R12 to 1.65 KHz (66% of 2.5 KHz) of
deviation per EIA specifications.
RADIO PROGRAMMING
F-3/F-4/F-30/F-40/F-320/F-420/F-1020/F-2020: For
Emergency ANI, program the radio’s option button
(P0-P3) as Opt 1 Momentary/Active Low.
F-3G/F-4G/F-14/F-24/F-33G/F-43G/F-120/F-220/F-
520/F-620/F-1720/F-1820: For Emergency ANI,
program the radio’s option button under Common >
Key & Display as OPT1 Momentary/L (Active Low).
F-30G/F-40G: For Emergency ANI, program the
radio’s option button under Common>Key & Display
as OPT11 Momentary/L (Active Low). If you use the
second options connector, program as OPT21
Momentary/L (Active Low).
OPERATION
ANI Encode: When the PTT Input is grounded, the
unit will assert the PTT Output and send the
programmed ANI tones out the TX Tone Output.
ENI Encode: When the Emergency Input is
grounded, the unit will assert the PTT Output and
send the programmed Emergency ANI tones out the
TX Tone Output.
TECHNICAL NOTES
Programming 2-tone: 2-tone ANI is programmed
with the Advanced Tone Defintions. In Frame 1,
Frequency 1 type in the frequency of the first tone
and type the length of the first tone in Frame 1
msec. In Frame 2 msec, type in the length of the
gap time. In Frame 3, Frequency 1 type in the
frequency of the second tone and type the length of
the second tone in Frame 3 msec.
F-30G/F-40G: It has been found on more recent
versions of the radio that the PTT In and PTT Out
connections on the options connector have been
reversed. In these versions, the PTT jumper should
not be cut and functions such as Time-Out-Timer
and Penalty Timer will not be available.
MIDIAN CONTACT INFORMATION
Midian Electronics Inc.
2030 N. Forbes Blvd. #101
Tucson, Arizona 85745 USA
Orders: 1-800-MIDIANS
Phone: 520-884-7981
Fax: 520-884-0422
Web: http://www.midians.com/
