Miele H 4886 BP BRWS+ User manual

Installation Instructions
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
H4884 BP, H4886 BP

Disposal of the packing
materials
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet and
cut off its power cord. Remove any
doors to prevent trapping hazards.
Caring for the environment
72

,CAUTION: Before servicing,
disconnect the power supply by
either removing the fuse, shutting off
the power main or manually
"tripping" the circuit breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous and
the manufacturer will not be held
responsible.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.
Only operate the appliance after it
has been installed into cabinetry.
Installer:
Please leave these instructions with
the consumer.
Power supply
The oven is equipped witha6ft.
(1.8 m) flexible power cord consisting
of 4 wires ready for connection to a
dedicated 3 pole, 4 wire grounded
power supply:
120/240 V, 60 Hz, 30 A fuse rating
or
120/208 V, 60 Hz, 30 A fuse rating
Black wire: connect to L1 (hot)
Red wire: connect to L2 (hot)
White wire: connect to N (neutral)
Green wire: connect to GND (ground)
A dedicated line and junction box
should be used to connect the oven to
a 30 A circuit.
Connection details are also given on the
diagram located on the top of the oven.
Data plate
The silver data plate is located along
the front side of the oven with the door
open.
Electrical connection
73

Miele appliances can be installed flush or proud. Discuss your installation
requirements with your architect, designer and installer.
Appliance and Cut-out Dimensions
74

aVent cut-out (min. 24" 2/ 150 cm2) possible at rear or platform of cabinet
bCut-out for power cord (min. 1" 2/3cm
2)
cPower cord
For the most current specifications see the Miele web site.
Appliance and Cut-out Dimensions
75

The oven must be installed into
cabinetry and be supported from
underneath.
,IMPORTANT INFORMATION
Certain cabinet materials and
finishes are very sensitive to high
temperatures. To eliminate the risk
of damage to surrounding cabinets,
a 24 square inch (2"x12") [150 cm2]
minimum opening must exist in the
cabinet to allow air to flow into and
around the appliance.
In addition, the oven vent at the
bottom of the door must not be
obstructed.
^Adhere the skid plates to the cabinet
floor.
^Prepare the door for removal.
Flip up the locking clamps on each
door hinge.
Installing the oven
76

^Slowly shut the door until the
protruding clamps stop the
movement. Pull the door upward.
^Connect the oven to the electrical
supply.
^Slide the oven into the cabinet and
align.
^Reinstall the door.
^Open the oven door and locate the
two mounting screw holes in the oven
frame. Mark and drill 6 mm pilot
holes. Secure the oven to the
cabinetry by inserting screws through
the frame and into the cabinetry.
Installing the oven
77

Set the time
"Enter Time: hh:mm" will appear in the
display once the oven is connected to
electricity.
^Set the current time using the
keypad.
^Save the time by touching the "OK"
control.
Installing the oven
78

79

Alteration rights reserved / 2311
(H 4884 BP, H 4886 BP)
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
M.-Nr. 07 964 270 / 00