Miele MasterChef KM452 User manual

Installation instructions
Ceramic Cooktop
KM 452
To prevent accidents
and machine damage,
read these instructions
before installation or use, M-Nr, 05 797 870

Contents
iMPORTANT SAFETY INSTRUCTmONS ................................ 4
installation ........................................................ 4
Minimum safety distance above the appliance ............................ 5

Appliance and cut-out dimensions
KM 452
iI
,7 Spring clips
,_2_
,_There must be at least ,'3,'3/ ,,(81ram)
J16
of usable depth on the right side of
the cut ouL
[] Make the countertop cut-out following
the dimensions given in the
illustration.
[] Remember to maintain a minimum
distance of 2" (50) mm between the
rear watl and a right or left hand side
wa!l. See also "Important Safety
instructions".
[] Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture. The materials used must be
heat resistant.
If, during installation, the seal around [:
the frame does not sit flush with the
countertop on the corners, ,!he il
ii corner radius max. R4 (s/16) can be _

installation
mnstaHing the spring dips Granite countertops
[] Fix the supplied spring clips _ at the
marked positions as shown above,
by laying them on the upper edge of
the cut-out and then securing them
with the 3.5 x 25 mm screws
supplied.
For granite countertops, the spring
clips _ must be placed in position and
secured with strong, double-sided
adhesive tape.
In addition coat the edges of the spring
clips with silicone sealant.
The screws are not needed for granite
cou ntertops.

installation
mnstaHing the cooktop
[] Feed the power cord down through
the cut-out and connect the
appliance to the power supply.
[] Position the cooktop on the spring
clips '_.
[] Then with a hand on each side of the
cooktop press down on the edges
evenly until it clicks into position.
When doing so make sure that the
cooktop seal sits tightly on the
countertop to ensure a correct seal is
provided.
The cooktop can now only be
removed with a special tool.
Thecooktopmustnotbeperm-
anently'sealed into the countertop ;:i
If the cooktop is sealed into position,
the countertop or appliance could be
damaged if the cooktop needs to be
removed for maintenance or service.
The sealing strip under the edge of the
top part of the cooktop provides a
sufficient seal for the countertop.

Electrical connection
@d_i_Qiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiid_J
z_CAUTION: Before servicing,
disconnect the power supply by ......
either removing the fuse, shutting off
the power main or manually
"tripping" the circuit breaker.
i nstallation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
i epairs and service by unqualified
persons could be dangerous and
the manufacturer will not be held
responsible.
i efore connecting the appliance to
the power supply, make sure that the
voltage and frequency listed on the
data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.
Only operate the cooktop after it has
been installed into the countertop.
Installer:
Please _eave these instructions with
the consumer,
Power supply
The cooktop is equipped with a flexible
power cord consisting of 3 wires ready
for connection to a grounded power
supply:
- 120/240 V,60 Hz, 50 A fuse rating
or
- 120/208 V,60 Hz, 50 A fuse rating
Black wire: connect to L1 (hot)
Red wire: connect to L2 (hot)
Green wire: connect to GND (ground)
A dedicated line and junction box
should be used to connect the cooktop
to a 50 A circuit.
For further information, see the wiring
diagram provided with the appliance.
_WARNING:
THiS APPLIANCE MUST BE
GROUNDED!

10