Miele DA 5690 W User manual

Operating and installation instructions
Cooker hood
DA 5690 W,
DA 5690 W EXT
To avoid the risk of accidents
or damage to this appliance,
it is essential to read these
instructions before it is installed
and used for the first time. M.-Nr. 09 204 070
en-GB

Caring for the environment..........................................3
Warning and Safety instructions .....................................4
Guide to the appliance ............................................10
Modes of operation ...............................................12
Miele|home .....................................................13
Con|ctivity ......................................................13
Operation .......................................................14
To switch the fan on s.............................................14
To select a power level .............................................14
Run-on option "5m15"..............................................15
To switch the fan off s.............................................15
Hob lighting n...................................................15
Operating hours counter l| ........................................16
Sensor tones .....................................................18
Cleaning and care ................................................19
Housing .........................................................19
Grease filters .....................................................20
Resetting the Grease filter operating hours counter.....................21
Fitting and replacing the charcoal filter .................................22
Resetting the Charcoal filter operating hours counter ...................22
Changing a halogen lamp ...........................................23
After Sales Service ...............................................24
Appliance dimensions.............................................25
Safety distance (S) ..............................................25
Installation ......................................................26
Assembly parts ...................................................26
Installation instructions .............................................28
Dismantling ......................................................28
Connection for air extraction .......................................29
Condensate trap ..................................................30
Silencer .........................................................31
Electrical connection .............................................32
Operation with Control module DSM 400 .............................33
Potential free connection .........................................33
Connection to a light switch .......................................33
Technical data ...................................................34
Contents
2

Disposal of the packing material
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Packaging e.g. cling film, polystyrene
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Caring for the environment
3

This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~This appliance is intended for use in
domestic households and in similar
working and residential environments
such as:
–Shops
–Offices and showrooms
and by residents in establishments
such as:
–Hostels and guest houses.
~It must only be used as a domestic
appliance to extract vapours and
remove odours from cooking.
~The cooker hood is not intended for
outdoor use.
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation.
~This appliance is not intended for
use by people with reduced physical,
sensory or mental capabilities, or lack
of experience or knowledge, unless
they are supervised whilst using it or
have been shown how to use it
correctly by a person responsible for
their safety.
Safety with children
~This appliance is only intended for
use by adults who have read these
instructions.
~This appliance is not a toy! To
prevent the risk of injury do not let
children play with the appliance or its
controls.
~Children under 8 years of age must
be kept away from the cooker hood
unless they are constantly supervised.
~Children 8 years and older may use
the cooker hood only if they have been
shown how to use it in a safe way and
understand the hazards involved.
~Please be aware that on cooker
hoods with halogen lighting, the lamps
will get very hot during use and remain
hot for some time after switching off. To
safeguard against burning, keep
children well away from the lamps at all
times.
Warning and Safety instructions
4

Technical safety
~Before installation, check the cooker
hood for visible signs of damage. Do
not install and use a damaged
appliance. It could be dangerous.
~Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
household electricity supply, otherwise
the appliance could be damaged.
Consult a qualified electrician if in any
doubt.
~The electrical safety of this
appliance can only be guaranteed if it
is correctly earthed. It is most important
that this basic safety requirement is
observed and regularly tested and
where there is any doubt, the
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~For safety reasons, this appliance
may only be used when it has been
fully installed.
~Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
~Installation, maintenance and
repairs may only be carried out by a
service technician authorised by the
manufacturer in strict accordance with
current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply.
Warning and Safety instructions
5

~Do not connect the appliance to the
mains electricity supply by a
multi-socket adapter or an extension
lead. These do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
~For appliances with an external fan
motor (...EXT models) the connection of
the two units must be made using the
connection cable and the plug
connectors.
These models may only be combined
with a Miele external motor.
~This appliance must not be used in
a non-stationary location (e.g. on a
ship).
~In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the guarantee.
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~Great care should be taken when
using the cooker hood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas hobs, cookers or ovens which draw
air in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
Warning and Safety instructions
6

In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the cooker
hood and the heating appliance are in
operation simultaneously, an
underpressure in the room of 0.04 mbar
(4 pa) is the maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the cooker hood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter (GasSafe
registered in the UK) or electrician
must be sought.
If the hood is being operated in
recirculation mode, the above
restrictions do not apply.
Warning and Safety instructions
7

Correct use
~Never use an open flame beneath
the cooker hood. To avoid the danger
of fire, do not flambé or grill over an
open flame.
When switched on, the cooker hood
could draw flames into the filter. Fat
particles drawn into the cooker hood
present a fire hazard.
~When using the cooker hood over a
gas hob, ensure that any burners in use
are always covered by a pan. Switch
the cooking zone off when a pan is
removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The cooker hood can become
damaged when exposed to excessive
heat.
~Always switch the cooker hood on
when using the hob, otherwise
condensation may collect in the hood,
which could cause corrosion.
~When cooking with oil or fat, chip
pans and deep fat fryers etc, do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the cooker hood on fire.
~Do not use the cooker hood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~The cooker hood can get very hot
during cooking due to heat rising from
the hob.
Do not touch the housing or the grease
filters until the cooker hood has cooled
down.
~Do not use a steam-cleaner to clean
this appliance. Steam could reach the
electrical components and cause a
short circuit.
Warning and Safety instructions
8

Correct installation
~Refer to the cooker or hob
manufacturer's instructions as to
whether a cooker hood may be
operated above the cooker/hob.
~The minimum safety distances
between the top of the cooker or hob
and the bottom of the cooker hood
given in the "Appliance dimensions"
section of this booklet must be
maintained, unless the hob
manufacturer states that a greater
safety distance is required.
If more than one cooking appliance is
fitted beneath the cooker hood, and
they have different minimum safety
distances to the cooker hood, select
the greater distance.
~Safety regulations prohibit the fitting
of a cooker hood over solid fuel stoves.
~All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from the Miele
Spare Parts department or from
builders' merchants.
~The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
Accessories
~Only use genuine Miele original
spare parts and accessories with this
appliance. Using spare parts or
accessories from other manufacturers
will invalidate the guarantee, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Warning and Safety instructions
9

Guide to the appliance
10

aTelescopic extension piece
bTower
cCanopy
dSensor controls
The symbols act as sensors. To select
a function, touch the relevant sensor.
An audible tone sounds briefly to
confirm selection.
eGrease filters
fRecirculation grille
(only for recirculation mode)
gHob lighting
hCharcoal filter
(special accessory for recirculation
mode)
iSensor for hob lighting
This sensor can be used to switch the
hob lighting on and off and is also a
dimmer switch.
jSensor for switching the fan on
and off
kSensors to select the fan power
level
lSensor for the run-on option
This sensor activates the run-on option.
The fan can be set to switch off
automatically after either 5 or 15
minutes.
mSensor for the grease filters
The sensor lights up when the grease
filters need to be cleaned.
It is used to reset the operating hours
counter every time the grease filters are
cleaned (see "Cleaning and care").
It can also be used to check and alter
the operating hours counter.
nSensor for the charcoal filter
The sensor for the charcoal filter lights
up when the charcoal filter used in
recirculation mode needs to be
replaced. For this to happen, the
operating hours counter needs to be
activated before the appliance is used
for the first time.
The sensor is used to reset the
operating hours counter every time the
charcoal filter is replaced (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
For information about using the
appliance, see "Operation".
Guide to the appliance
11

The cooker hood works with
. . . air extraction:
The air is drawn in and cleaned by the
grease filters and directed outside.
If the on-site ventilation system does
not have a non-return flap, the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
. . . air recirculation:
(this requires an optional conversion kit
and charcoal filter: see "Technical
Data")
The air is drawn in and cleaned first by
the grease filters and then by a
charcoal filter. The cleaned air is then
recirculated back into the kitchen
through grilles in the top of the cooker
hood telescopic extension piece.
Before using the cooker hood in
recirculation mode, ensure that the
charcoal filter is in place. See
"Cleaning and care".
...anexternal motor:
(...EXT models only)
The ...EXT models are designed to be
connected to an external motor located
outside the room.
The external motor is connected to the
cooker hood by means of a control
cable, and is operated by the controls
on the cooker hood.
Modes of operation
12

Con|ctivity
This cooker hood is communication
enabled.
Communication module XKM 2000 DA
a, available as an optional extra,
enables the operation of the cooker
hood to be automatically controlled by
the operating status of a Miele electric
hob with onset controls.
For communication to take place, the
hob must be fitted with the appropriate
communication module b.
The hob transmits information about its
operating status to the cooker hood via
the household power supply
(Powerline) c.
–When the hob is switched on the
cooker hood hob lighting also comes
on and then after a short time the fan
switches on.
–During cooking the cooker hood
automatically sets its power level
according to the number of cooking
zones in operation and their power
levels.
–After switching the hob off the fan
and the hob lighting will switch off
automatically after a period of time.
For detailed information about this
function please read the separate
instruction booklet supplied with the
XKM 2000 DA communication module.
The communication module is fitted to
the cooker hood in the area of the
motor and is connected to the controls
of the cooker hood.
This module must be installed by a
Miele service technician or suitably
qualified electrician.
Miele|home
13

To switch the fan on s
^Touch the ssensor.
The fan will come on at power level 2.
The sand 2sensors will light up.
To select a power level
Depending on the intensity of the
cooking vapours, levels 1to 3are
usually sufficient for normal cooking.
^Select the level you require by
touching the 1,2or 3sensors.
Intensive setting
^For short periods of cooking food
with intensive vapours and a strong
aroma, e.g. when searing meat, you
may wish to select level 4, the
Intensive setting.
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it always only runs for 10 minutes
before reverting automatically to level 3.
^To set this option, both the fan and
the hob lighting must be switched off.
^Touch the Run-on option sensor m
for approx. 10 seconds until the 1
sensor lights up.
^Touch in turn
– the nsensor,
– the 1sensor, and
– the nsensor again.
If Automatic switch-off is not activated,
the 1and 4sensors will flash.
^Touch the 4sensor to activate Auto-
matic switch-off.
The 1and 4sensors will now light up
constantly.
Touch the 1sensor to deactivate the
Automatic switch-off function.
^Confirm your selection by touching
the msensor.
–If you do not confirm within 4
minutes, the cooker hood will
automatically revert to the original
setting.
Operation
14

Run-on option "5m15"
It is advisable to leave the fan running
for a few minutes after cooking has
finished to neutralise any lingering
odours in the air.
The fan can be set to switch off
automatically after either 5 or 15
minutes.
^After cooking has finished, touch the
Run-on option sensor mwhilst the
fan is still running
–Touch once = The fan will switch off
after 5 minutes (5mwill light up).
– Touch twice = The fan will switch off
after 15 minutes (m15 will light up).
To switch off the run-on option, touch
the run-on option sensor again. The
appliance will then not switch off
automatically.
To switch the fan off s
^Touch the ssensor to switch the fan
off.
Hob lighting n
The hob lighting can be switched on
and off independently of the fan.
To switch the hob lighting on
^Touch the nsensor briefly.
The lighting will switch on at maximum
brightness.
To dim the hob lighting
The brightness of the hob lighting can
be adjusted.
^With the lighting switched on, touch
and hold the nsensor.
The brightness will gradually dim until
you release the sensor.
^To increase the brightness, touch the
sensor again to the level required,
then release it.
If you keep your finger on the sensor,
the light will continually change
between bright and dim.
To switch the hob lighting off
^Touch the nsensor briefly.
Safety switch-off
Should the cooker hood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
^Touching the ssensor will switch the
fan back on again.
Operation
15

Operating hours counter l|
The number of hours the appliance has
been in operation is stored in memory.
The operating hours counters tell you
when the grease filters or charcoal filter
need to be cleaned or replaced.
Checking the grease filter operating
hours counter
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the lsensor will light
up.
The grease filters must then be cleaned
and the operating hours counter reset
(see "Cleaning and Care").
To check the percentage of time set
already used:
^Touch the ssensor to switch the fan
on.
^Touch and hold the lsensor.
One or more of the 1to 4sensors will
flash.
The number of flashing sensors
indicates the percentage of the
operating time which has already been
used up.
Sensor 1=25%
Sensors 1and 2=50%
Sensors 1to 3=75%
Sensors 1to 4= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
Altering the grease filter operating
hours counter
You can set the operating hours
counter to suit the type of cooking you
do.
The operating hours counter is set at
the factory for 30 hours.
Select a shorter time of 20 hours if you
fry a lot.
If you only cook occasionally, we still
recommend 20 hours because grease
which has built up gradually over a long
period of time will harden on the grease
filters and make cleaning more difficult.
If you use very little fat for cooking,
select a longer time of 40 or 50 hours.
To alter the operating time:
^Touch the ssensor to switch the fan
off.
^Touch the mand lsensors at the
same time.
The grease filter sensor land one of
the fan power level sensors 1to 4will
flash.
Sensors 1to 4indicate the time set:
Sensor 1= 20 hours
Sensor 2= 30 hours
Sensor 3= 40 hours
Sensor 4= 50 hours
^Touch the 1sensor to select a shorter
time and the 4sensor to select a
longer time, until the time required
has been set.
Operation
16

^Confirm your selection by touching
the lsensor.
All the lamps will go out.
If you do not confirm within 4 minutes,
the cooker hood will automatically
revert to the original setting.
Activating and altering the charcoal
filter operating hours counter
(in recirculation mode)
The charcoal filter is needed for
recirculation mode.
On delivery, the operating hours counter
for the charcoal filter is deactivated.
For recirculation mode, the operating
hours counter needs to be set to suit
the type of cooking you do:
^Touch the ssensor to switch the fan
off.
^Touch the mand |sensors at the
same time.
The charcoal filter sensor |and one of
the fan power level sensors 1to 4will
flash.
Sensors 1to 4indicate the time set:
Sensor 1= 120 hours
Sensor 2= 180 hours
Sensor 3= 240 hours
Sensor 4= Deactivated
^Select the level you require by
touching the 1, 2 or 4 sensor.
^Confirm the selection by pressing the
charcoal filter sensor |.
All the lamps will go out.
If you do not confirm within 4 minutes,
the cooker hood will automatically
revert to the original setting.
The charcoal filter touch sensor |will
light up after the cooker hood has
operated for the number of hours set.
^The charcoal filter must then be
replaced with a new one (see
"Cleaning and care").
^Afterwards, the operating hours
counter will need to be reset (see
"Cleaning and care").
Checking the charcoal filter
operating hours counter
To check the percentage of time set
already used:
^Touch the ssensor to switch the fan
on.
^Touch and hold the |sensor.
One or more of the 1to 4sensors will
flash.
The number of flashing sensors
indicates the percentage of the
operating time which has already been
used up.
Sensor 1=25%
Sensors 1and 2=50%
Sensors 1to 3=75%
Sensors 1to 4= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
Operation
17

Sensor tones
When selecting a function with the
sensors, an audible tone will sound
briefly to confirm.
The audible tone can be deactivated.
^Touch the ssensor to switch the fan
off.
^Touch the 4sensor and the grease
filter sensor lat the same time for
approx. 5 seconds until a tone
sounds briefly. The audible tone is
now switched off for all functions.
^To reactivate the audible tone, repeat
the above process.
After the cooker hood has been
disconnected from the mains electricity
supply or after a power cut, the audible
tone is activated regardless of the last
setting.
Operation
18

A range of Miele branded cleaning and
conditioning products is available to
order from Miele (see back page for
details) or the via the internet at
www.miele-shop.com.
,Before any cleaning or
maintenance work is carried out,
disconnect the cooker hood from the
mains supply.
,Halogen lamps get very hot
during use and remain hot for some
time after being switched off. The
hot lamps are also susceptible to
damage from damp cleaning. Wait a
few minutes after switching off
before commencing cleaning.
Housing
General
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
^All external surfaces and controls can
be cleaned using a Miele E-Cloth or
with warm water and a little
washing-up liquid applied with a well
wrung-out soft sponge or cloth.
^Wipe the surfaces dry using a soft
cloth.
Do not use:
–cleaning agents containing soda,
acids, chlorides or solvents,
–abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents.
These will damage the surface
material.
Important for appliances with
stainless steel surfaces
Stainless steel surfaces can be cleaned
using the Miele E-Cloth or with a
suitable, non-abrasive, proprietary
cleaning agent for stainless steel,
following the manufacturer's
instructions on the packaging.
To help prevent re-soiling, a
conditioning agent for stainless steel
can also be used. Follow the
manufacturer's instructions on the
packaging.
Important for appliances with
lacquered surfaces
It is very difficult to clean this type of
surface without causing minor marks to
the surface material.
This can become particularly
noticeable with darker colours and if
there is halogen lighting in the kitchen.
Cleaning and care
19

Important for appliances with glass
surfaces
^Glass surfaces can be cleaned using
a proprietary non-abrasive cleaning
agent designed specifically for use
on glass.
Do not use:
–abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
–abrasive sponges, e.g. pot scourers
or sponges which have been
previously used with abrasive
cleaning agents,
– oven sprays.
Grease filters
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
cooker hood.
The grease filters should be cleaned
regularly (at least every 3-4 weeks) to
avoid a build-up of grease, but always
clean immediately if the lsensor lights
up.
,An oversaturated filter is a fire
hazard.
^To take out the grease filters, release
the locking clip on the filters, lower
the filters 45°, unhook them at the
back and remove them.
To avoid damaging the filters or the
hob below, make sure you hold the
filters securely at all times when
handling them.
Cleaning and care
20