Miele PW 6201 EL User manual

Installationsplan / Installation plan
Installatietekening
Plan d`installation
Pianta di installazione
Plano de instalación
Plano de instalação
Σχέδιο εγκατάστασης
Asennusohje
Installasjonsplan
Installationsplan G
PW 6201 EL
Materialnummer / Mat. no.: 06 478 890
Änderungsstand / Version: 00
Datum Zeichnung / Drawing date: 01.07.2004
Datum Legende / Legend date: 11.08.2004

Installationsplan PW 6201 EL
Stand: 11.08.2004 Seite 7
Technical datasheet
Washer-extractor:
Heating:
PW 6201
Electric (EL)
Legend:
Circled, bold-type abbreviations:
Connection required
Abbreviations surrounded by broken circle:
Connection optional or required, depending on model
G
Optional extras:
Miele plinth UG/UO 6020
(UG = Box plinth/UO = Open plinth)
UM
Height Model mm 237
Width UG (UO) mm 920 (900)
Depth UG (UO) mm 1049 (1009)
Concrete platform Concrete platform optional (Min. quality B15)
Recommended height mm 237
BS
Minimum height mm 100
Recommended width mm 920
Recommended depth mm 1020
Ensure good anchorage!
Machine connections:
1. Standard voltage (as supplied) V 3N AC 380-415Electrical
connection Frequency Hz 50 - 60
Rated load kW 21
Fuse rating A 3 × 35
Supply lead, min. cross section (M 32) mm² 5 × 6.0
2. Standard voltage (as supplied) V 3 AC 220-240
Frequency Hz 50 - 60
Rated load kW 21
Fuse rating A 3 × 63
Supply lead, min. cross section (M 40) mm² 4 × 16
3. Standard voltage (as supplied) V 3 AC 440
Frequency Hz 60
Rated load kW 21
Fuse rating A 3 × 35
Supply lead, min. cross section (M 32) mm² 4 × 6.0
Plug and socket connection recommended to facilitate
electrical safety tests. Socket must be accessible after
installation.
In the case of hard-wired connections, an all-pole mains
switch with a minimum contact gap of 3 mm must be
provided.
The use of an earth leakage circuit breaker (ELCB) is strongly
recommended.
If necessary, equipotential bonding with good galvanic contact
must be provided in accordance with all appropriate national
and local regulations.
Connection cable, min. cross-section mm² 4 × 1.5
Peak load
management Input leads should not be in direct contact with any source of
heat.
Input signal via potential-free (galvanically separated) contact.

Installationsplan PW 6201 EL
Stand: 11.08.2004 Seite 8
Min. flow pressure kPa 100
Max. pressure kPa 1000
Cold water
(Soft water)
Max. throughput (if hot water supply is not available) l/min 26 (36)
On-site connection thread according to DIN 44 991 Inch ¾" external thread
Length of connection hose (supplied) mm 1500
Water requirements (average for 60°C programme)
Standard connection [with hot water connection] l/h not yet available
Additional requirements if hot water supply is not available.
Max. temperature °C 70
Min. flow pressure kPa 100
Hot water
Max. pressure kPa 1000
Max. throughput l/min 10
On-site connection thread according to DIN 44 991 Inch ¾" external thread
Length of connection hose (supplied) mm 1500
Water requirements (average for 60°C programme)
Standard connection [with hot water connection] l/h not yet available
If no hot water supply, connect hose to cold water!
Min. flow pressure kPa 100
Max. pressure kPa 1000
Raw water
(Optional) Max. throughput l/min 32
On-site connection thread according to DIN 44 991 Inch ¾" external thread
Length of connection hose (supplied) mm 1.500
Water requirements (average for 60°C programme)
Standard connection [with hot water connection] l/h not yet available
If connected to raw water supply, subtract cold water (soft)
volume.
If no raw water supply, connect hose to cold water!
Max. temperature °C 95
Machine drain connection (da× s × l) [DN 70] mm 75 × 1.9 × 115
On-site drain connection (di× s × l) [DN 70 sleeve] mm 75 × 1.9 × 50
Drainage via
dump valve
Max. transient throughput l/min 200
Vented drainage required. If ventilation is insufficient, fit Miele
kit, Mat. no. 05238090.
Drain manifolds serving several machines must be of
sufficient cross-section.
Foam vent
(Optional)
A drainage system for foam escaping from the drain vent can
be built using standard drain pipe sections. An 87° branch
with an end cap should be provided for this purpose.
Machine vent Vent machine interior to prevent excessive rise in pressure.
Miele plinth UG/UO 6016Fittings (supplied)
4 × metal angled brackets (to secure machine to plinth)
4 × screws DIN 571 (Ø × length) mm 8 × 80
4 × rawl plugs (Ø × length) mm 12 × 60
Machine must be secured!
Fixing materials for floating screed floor to be provided on site
On concrete platform
2 × screws DIN 571 (Ø × length) mm 8 × 80
2 × rawl plugs (Ø × length) mm 12 × 60
Machine must be secured!
Fixing materials for floating screed floor to be provided on site

Installationsplan PW 6201 EL
Stand: 11.08.2004 Seite 9
Without plinth
2 × screws DIN 571 (Ø × length) mm 8 × 80
2 × rawl plugs (Ø × length) mm 12 × 60
Machine must be secured!
Fixing materials for floating screed floor to be provided on site
Machine data Width mm 920
Depth mm 1020
Height mm 1400
Knocked-down dimensions (W × H) mm 1100 x 1500
Recommended gap to opposite wall mm 1450
Net weight kg 499
Dynamic floor load, max. N 6076
Static floor load, max. N 5543
Drum frequency, max. Hz 18.3
Average heat dissipation
(dependent on ambient room temperature and programme
selected)
W not yet available
Installation should only be carried out by authorised fitters in accordance with valid regulations!
Observe installation instructions when installing machine! All rights reserved! Measurements in mm