Miele PW 6241 User manual

Operating and installation instructions
Commercial washing machine
PW6241
PW6321
To avoid the risk of accidents or damage to the
machine, it is essential to read these instruc-
tions before it is installed and used for the first
time.
en-GB
M.-Nr. 12 149 550

Contents
2
Warning and Safety instructions.................................................................................... 4
Explanation of the safety instructions and warnings on the machine............................... 4
Intended use...................................................................................................................... 5
Foreseeable misuse........................................................................................................... 6
Technical safety................................................................................................................. 8
Correct use........................................................................................................................ 10
Chlorine and component damage..................................................................................... 12
Accessories....................................................................................................................... 13
Disposing of your old machine.......................................................................................... 13
Caring for the environment ............................................................................................ 14
Description of the machine ............................................................................................ 16
Machine description.......................................................................................................... 16
Control panel..................................................................................................................... 17
Function buttons ............................................................................................................... 18
Programme card for the supervisor................................................................................... 19
Washing............................................................................................................................ 20
Initial commissioning......................................................................................................... 20
Preparing the laundry ........................................................................................................ 20
Emptying pockets ......................................................................................................... 20
Load sizes ..................................................................................................................... 21
Washing with detergent drawers....................................................................................... 22
Adding detergent using the detergent drawer............................................................... 22
Bleaching agents........................................................................................................... 22
Dyes, dye removers and descalers ............................................................................... 23
Detergent dispensing .................................................................................................... 23
Dispensing quantity....................................................................................................... 23
Water hardness levels ................................................................................................... 24
Selecting a programme ..................................................................................................... 25
Selecting the Pre-wash, Starch stop or Without spin additional functions....................... 25
Changes before starting the programme .......................................................................... 26
Load size ....................................................................................................................... 26
Temperature .................................................................................................................. 26
Spin speed .................................................................................................................... 26
Maximum spin speeds .................................................................................................. 26
Starting the programme ................................................................................................ 26
Opening the drum door after the programme has finished........................................... 28
Procedure in the event of a programme interruption during operation ......................... 29
Washing by card operation............................................................................................. 30
Card operation................................................................................................................... 30
Laundry load operation ..................................................................................................... 31
Additional functions ........................................................................................................ 32
Temporarily changing the language .................................................................................. 32
Start time........................................................................................................................... 33
Cancelling the start time ............................................................................................... 33
With pre-wash ................................................................................................................... 34
Without spin ...................................................................................................................... 35
Programme stop................................................................................................................ 35
Programme cancellation.................................................................................................... 36

Contents
3
Cancelling a locked programme........................................................................................ 36
Skipping a programme...................................................................................................... 37
Optional modules ............................................................................................................ 38
Liquid dispensing (optional for machines with dispenser compartment).......................... 38
Deselecting dispensing ..................................................................................................... 39
Amount to be dispensed................................................................................................... 39
Commissioning the dispensing pumps............................................................................. 39
Dispenser calibration......................................................................................................... 40
Cleaning and maintenance of the dispensing system....................................................... 41
Peak-load negotiation ....................................................................................................... 41
Communication module .................................................................................................... 42
Operating data................................................................................................................... 42
Total data........................................................................................................................... 44
Programme data................................................................................................................ 45
Delete data ........................................................................................................................ 47
Weighing system/weighing plinth...................................................................................... 48
Resetting the load display to zero................................................................................. 48
Problem solving guide .................................................................................................... 49
The drum door cannot be opened .................................................................................... 49
The safety catch of the door handle is disengaged .......................................................... 49
Power failure during the wash cycle; opening the door in an emergency......................... 50
In the event of a brief power failure:.............................................................................. 50
Possible reasons for increased levels of foaming ............................................................. 52
Service interval and DGUV display ................................................................................... 53
Customer Service Department.......................................................................................... 56
Cleaning and care ........................................................................................................... 57
Build-up of rust.................................................................................................................. 57
Cleaning the detergent drawer, detergent compartments and siphons............................ 58
Drum shaft bearings.......................................................................................................... 60
Downtimes ........................................................................................................................ 60
Meaning of the symbols on the data plate.................................................................... 61
Sound emissions............................................................................................................... 61
Installation........................................................................................................................ 62
Transit bars........................................................................................................................ 62
Installing the machine on ships......................................................................................... 63
Water connection .............................................................................................................. 64
Water connections ........................................................................................................ 64
Connection to the water inlet/drainage ......................................................................... 64
Connection to the cold water supply ............................................................................ 65
Use of non-return valves ............................................................................................... 65
Regulations for Austria...................................................................................................... 66
Dispensing agent connection to the mixer compartment ................................................. 66
Electrical connection......................................................................................................... 68
Equipotential bonding ....................................................................................................... 68
Connecting the dispensing pumps ................................................................................... 69
Steam connection ............................................................................................................. 69
Quick Start Guide ............................................................................................................ 70

Warning and Safety instructions
4
Explanation of the safety instructions and warnings on the
machine
Read the operating instructions
Read all the instructions, e.g. the installation instructions
Warning, hot surfaces
Warning, voltage up to 1000volts
Earthing
Equipotential bonding
This washing machine complies with all current local and national
safety requirements. However, inappropriate use can lead to per-
sonal injury and damage to property.
Read the operating instructions carefully before using the washing
machine. They contain important information on safety, installation,
use and maintenance. This prevents both personal injury and dam-
age to the washing machine.
In accordance with standard IEC60335-1, Miele expressly and
strongly advises that you read and follow the instructions in the
chapter on installing the washing machine as well as the safety in-
structions and warnings.
Miele cannot be held liable for damage caused by non-compliance
with these instructions.
Keep these operating instructions in a safe place and pass them on
to any future owner.
When instructing other people how to use the washing machine,
they must be made aware of these safety and warning instructions.

Warning and Safety instructions
5
Intended use
 The washing machine is only suitable for washing fabrics with a
care label stating that they are suitable for machine washing. Any
other applications may be dangerous. The manufacturer cannot be
held liable for damage resulting from incorrect or improper use or op-
eration of the machine.
 This washing machine must be used as described in the operating
instructions and must be checked on a regular basis to make sure it
is functioning correctly. Maintenance must be carried out when ne-
cessary.
 The washing machine is not suitable for outdoor use.
 Do not install your washing machine in a room where temperatures
below freezing may occur. Frozen hoses are at risk of tearing or burst-
ing. The reliability of the electronic module may be impaired at tem-
peratures below freezing point.
 This washing machine is intended only for use in a commercial en-
vironment.
 The machine may only be operated when the following conditions
are met:
- The ship’s hull is longer than 24metres.
- The list of the vessel is not more than 2°.
- Any external vibration is no more than 150Hz at an amplitude of
0.35mm.
The safe operation and correct functioning of the machine can
only be guaranteed if the above conditions are met.
 The machine must not be operated on an open deck.
 Machines that do not carry the “CSAC/US” safety mark comply
with European safety regulations.
These machines must not be operated in the USA.
 This machine must only be installed by a qualified specialist who
has made sure that the conditions for its safe use are met.
 When installing this machine, it must be securely fixed to the floor.
Failure to do this could result in personal injury, damage to the ma-
chine and damage to other objects and installations.
 The use of industrial laundry machines on vessels operating on in-
land waterways and within the 3-mile zone is only permitted if the
machine is approved for the country or countries in question. This
does not affect use on vessels in international waters, including sea-
ports.
 This washing machine is only intended for items of laundry which
have not been impregnated with dangerous or inflammable sub-
stances.

Warning and Safety instructions
6
 For disinfection procedures, use temperatures, holding times, li-
quor ratios and, if necessary, disinfectants to achieve the required in-
fection prophylaxis in accordance with guidelines and microbiological
and hygienic standards.
 Disinfection programmes must not be interrupted, as this can have
a limiting effect on the disinfection result. It is the operator's respons-
ibility to ensure that the standard of disinfection in thermal as well as
chemo thermal procedures is maintained by carrying out suitable val-
idation tests.
 If the laundry has special result quality requirements, such as rins-
ing result, an absence of particles, wettability and liquid permeability,
the procedure must be validated accordingly. The supervisor must
guarantee the reprocessing standard with regular quality checks.
 Do not store or use petrol, paraffin or any easily flammable sub-
stances near the washing machine. There is a risk of fire and explo-
sion.
 If the washing machine is operated in a publicly accessible place, it
is the supervisor’s responsibility to ensure that suitable measures are
in place to protect users from any source of risk or danger.
 This washing machine can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience or
knowledge, if they are supervised whilst using it or have been shown
how to use it in a safe way and understand and recognise the con-
sequences of incorrect operation.
 Children under the age of 8 must not be allowed near the washing
machine unless they are constantly supervised.
 Children over the age of 8 may only use the washing machine
without supervision if its operation has been clearly explained to them
and they are able to use it safely. Children must be able to under-
stand and recognise the possible dangers caused by incorrect opera-
tion.
 Children may not carry out cleaning or maintenance on the wash-
ing machine unsupervised.
 Always supervise any children in the vicinity of the washing ma-
chine. Never allow children to play with the washing machine.
 Any uses other than those listed above are prohibited. The manu-
facturer accepts no liability in such cases.
Foreseeable misuse
 Never use solvent based cleaning agents, e.g. those containing
benzene, in this washing machine. Doing so may result in damage to
component parts and create toxic steam and fumes. Risk of fire and
explosion!

Warning and Safety instructions
7
 When washing with high temperatures, remember that the porthole
glass becomes hot. Do not let children touch it during a wash pro-
gramme.
Danger of burning!
 Close the drum door after each wash cycle. This will prevent:
- Children climbing into the washing machine or hiding things in it.
- Pets or other small animals climbing into the washing machine.
 Do not damage, remove or bypass the safety components or con-
trol elements of this washing machine.
 Machines with a damaged control panel, wires or cables must not
be used until they have been repaired.
 The water generated during washing is suds and not drinking wa-
ter. Drain the suds into a proper drainage system.
 Always make sure that the drum is stationary before reaching in to
remove laundry. Reaching into a moving drum is extremely danger-
ous. Danger of injury.
 Be careful not to put your hands in the gap between door and
frame when closing the drum door.
 If the detergent compartment drawer is open and any of the dis-
penser drawers are missing, there is a danger of scalding from
splashing water.
Do not operate the machine if any of its components are missing.
 It is particularly important to observe manufacturer's instructions
when using a combination of cleaning agents and special application
products. Products must only be used for applications approved by
the manufacturer to avoid any material damage or the occurrence of
strong chemical reactions.

Warning and Safety instructions
8
Technical safety
 This washing machine must be installed by the MieleCus-
tomerService Department or by an authorised dealer.
 Before setting up the washing machine, check it for any externally
visible damage. Do not install or use a damaged washing machine.
 The electrical safety of this washing machine can only be guaran-
teed when correctly earthed. It is most important that this basic
safety requirement is regularly tested, and where there is any doubt
the on-site wiring system should be inspected by a qualified electri-
cian. Miele cannot be held liable for the consequences of an inad-
equate earthing system (e.g. electric shock).
 Unauthorised repairs could result in unforeseen dangers for the
user, for which the manufacturer cannot accept liability. Repairs
should only be undertaken by a Miele approved service technician,
otherwise any subsequent damage will not be covered by the guaran-
tee.
 Do not make any alterations to the machine, unless authorised to
do so by Miele.
 Disconnect the washing machine from the power supply in the
event of a fault and for cleaning and maintenance. The washing ma-
chine is only electrically disconnected from the power supply when:
- The plug of the washing machine is unplugged, or
- The mains fuse is disconnected, or
- The screw-in fuse has been completely removed
See also “Installation – Electrical connection”.
 Washing machines with a damaged control element or cable insu-
lation must not be used until they have been repaired.
 Only operate the washing machine when all removable outer pan-
els are in place so that it is impossible to touch an electrical compon-
ent or moving part.
 In the event of a fault or for cleaning and maintenance purposes,
the washing machine must be isolated from the electricity supply. It is
only completely isolated when:
- The plug of the washing machine is unplugged, or
- The mains fuse is disconnected, or
- The screw-in fuse has been completely removed
 See also “Installation – Electrical connection”.
 The plug for the washing machine must always be kept accessible
so that the machine can be easily disconnected from the power sup-
ply.

Warning and Safety instructions
9
 The washing machine may only be connected to the water supply
using the set of hoses supplied with the machine. Old sets of hoses
must not be re-used. Check the sets of hoses regularly for signs of
wear. Change the sets of hoses in good time to avoid the risk of leaks
and subsequent water damage.
 Faulty components must only be replaced by genuine Miele spare
parts. Miele can only guarantee the safety standards of the appliance
when Miele spare parts are used.
 The cause of any leaks must be dealt with before the washing ma-
chine is restarted. Disconnect the washing machine immediately if
any water leaks out.
 Steam heating malfunctions can result in high temperatures at the
door, the dispenser and inside the drum (in particular at the edge of
the drum). There is a risk of slight burns.
This only applies to machines with steam heating.
 All relevant national provisions and regulations (DGUV in Germany)
relating to accident insurance are applicable to this machine. It is re-
commended to carry out testing in accordance with the regulatory
framework described in DGUV100-500 /Chapter 2.6/ Section 4. The
test book required for the documentation is available from Miele.
 Follow the instructions in “Installation”.
 If the machine is to be hard-wired, there must be a means of dis-
connecting all poles from the power supply. The mains switch must
be close to the washing machine and be clearly identifiable, un-
hindered and easily accessible at all times.
 If the machine’s mains connection cable has been damaged, it
must be replaced by the manufacturer or a qualified specialist.
 The power supply must be disconnected when performing main-
tenance or replacing parts on the machine. If the plug needs to be
disconnected from the socket, the operating personnel must ensure
that the plug remains disconnected at all times.

Warning and Safety instructions
10
Correct use
 The maximum dry laundry weight is 24kg for PW6241 and 32kg
for PW6321. See the “Programme chart” for the maximum recom-
mended load sizes for individual programmes.
 Before using the washing machine for the first time, check that the
transport safety devices have been removed (see “Installation – Re-
moving the Transport safety devices”). During spinning, transport
safety devices which are still in place may result in damage to both
the washing machine and adjacent furniture or machines.
 Never try to open the drum door of the washing machine using
force. The door can only be opened when a corresponding message
appears in the display.
 When washing with high temperatures, remember that the porthole
glass and drum door become hot. You must therefore keep children
away from the porthole glass and drum door during the wash cycle.
 Close the drum door after each wash cycle. This will prevent:
- Children climbing into the washing machine or hiding things in it.
- Pets or other small animals climbing into the washing machine.
 Always close the drum door carefully. There is a risk of crushing
and injury by shearing in the area around the hinges of the drum door.
 It must be possible to open the drum door fully. There must be no
doors or other structural elements in the vicinity which prevent the
drum door from opening.
 Always make sure that the drum is stationary before reaching in to
remove laundry. Touching a moving drum poses a significant risk of
injury.
 The procedures and machines listed here are not medical devices.
Observe the programme descriptions and procedural information in
the programme chart.
 Laundry is only disinfected in programmes with a disinfection step.
All other programmes do not have a disinfection step (see the “Hy-
giene” programme chart). If laundry that has not been disinfected is
transferred to the “clean” side of the washing machine, germ transfer
or contamination may occur. The transfer of non-disinfected laundry
to the “clean” side is the sole responsibility of the supervisor.
 This washing machine may only be operated without supervision if
there is a floor drain (gully) in the direct vicinity of the washing ma-
chine.

Warning and Safety instructions
11
 Disinfectants and detergents often contain chlorine-containing
compounds. When agents containing chlorine dry on stainless steel
surfaces, the resulting chlorides can attack the stainless steel and
produce rust. Protect your washing machine from rust damage by us-
ing chlorine-free agents to wash, disinfect and clean the stainless
steel surface. If in doubt, have the manufacturer confirm the suitability
of the agent.
If agents containing chlorine get onto the stainless steel surface,
clean the stainless steel surface immediately with water. Then use a
cloth to dry the stainless steel surface.
 It is particularly important to observe manufacturer’s instructions
when using a combination of cleaning agents and special application
products. Agents must only be used for applications approved by the
manufacturer to avoid any material damage or the occurrence of
strong chemical reactions. Confirmation must be sought from the
manufacturer that using the agent in the washing machine will not
cause damage.
 If the correct amount of detergent is dispensed, the machine
should not need to be descaled. If, however, you do wish to descale
it, only use proprietary non-corrosive descaling agents and strictly
observe the instructions on the packaging. Special descaling agent is
available from Miele. Strictly observe the instructions for the descal-
ing agent.
 Close the stopcock if the machine is to be left for any length of
time (e.g. while on holiday), especially if there is no floor drain (gully)
in the immediate vicinity.
 Take care to ensure that foreign objects (e.g. nails, pins, coins, pa-
per clips) do not find their way into the machine with the laundry. For-
eign objects may damage components of the machine (e.g. suds
container, drum). Damaged components can damage the laundry.
 Textiles which have been pre-treated in solvent-based cleaning
agents must be rinsed in clean water before being washed in the ma-
chine. Note that solvent residues may only be discharged into waste
water in compliance with local legislation.
 Never use solvent based cleaning agents, e.g. those containing
benzine in this machine. Doing so may result in damage to compon-
ent parts and create toxic fumes. Risk of fire and explosion!
 Do not store chemicals (liquid detergents, additives) on the ma-
chine lid. They may cause discolouration or lacquer damage. Acci-
dently spilled chemicals should be removed immediately with a wet
cloth from the surface.
 There is a fan outlet on the back of the machine. Under no circum-
stances must this be blocked. Please observe the minimum distance
on the installation diagram.

Warning and Safety instructions
12
 Recommending chemical cleaning agents does not mean that the
machine manufacturer is responsible for the influences of these
agents on the laundry and the washing machine. Please note that un-
disclosed product changes by the manufacturers of these agents
may affect the quality of the wash result.
 Only use dyes, dye removers and descalers suitable for use in a
washing machine. The manufacturer’s instructions on the packaging
must be observed.
 Colour run and dye removers contain sulphur compounds which
can cause damage such as corrosion. Do not use these products in
this machine.
 Check the wash result of laundry contaminated with biological oils
or greases. Inadequately washed laundry can cause spontaneous
combustion during the drying process. Use special detergents or
wash programmes for this kind of laundry.
 Do not use a pressure washer or hose to clean the washing ma-
chine.
Chlorine and component damage
 Frequent use of chlorine products increases the risk of damage to
components.
 The use of substances containing chlorine, such as sodium hypo-
chlorite and chlorine bleach in powder form, can however result in
damage of the protective layer of stainless steel and corrosion on
components. Therefore, refrain from using substances containing
chlorine. Use oxygen-based bleaching agents instead.
If, however, chlorine bleaching agents are used, an anti-chlorine treat-
ment must always be carried out. Otherwise, both the washing ma-
chine components and the laundry may suffer persistent and irrepar-
able damage.
 Anti-chlorine treatment must be carried out immediately after
chlorine bleaching agents have been used. Hydrogen peroxide as
well as oxygen-based detergents and bleaching agents are suitable
for anti-chlorine treatment. The suds must not be drained in between.
Treatments with thiosulphates can result in gypsum-like deposits par-
ticularly when used in combination with hard water. This gypsum can
build up in the washing machine or cause incrustations on the laun-
dry. Treatment with hydrogen peroxide is recommended over treat-
ment with thiosulphates because hydrogen peroxide neutralises
chlorine.
The exact dispensing quantities and the treatment temperatures re-
quired must be set and tested on site in accordance with the dis-
pensing recommendations of the detergent and cleaning agent man-
ufacturers. The laundry must also be tested to check whether it con-
tains any active chlorine residues.

Warning and Safety instructions
13
Accessories
 Accessory parts may only be fitted when expressly approved by
Miele. If other parts are used, guarantee, performance and product li-
ability claims will be invalidated.
Miele cannot be held liable for damage caused by non-compliance
with these Warning and Safety instructions.
Disposing of your old machine
 Ensure that the door locks are unusable when disposing of or
scrapping old washing machines. This will prevent the risk of children
playing accidentally locking themselves in and endangering their
lives.

Caring for the environment
14
Disposal of the packing material
The packaging is designed to protect against transportation damage.
The packaging materials used are selected from materials which are
environmentally friendly for disposal and should be recycled.
Recycling the packaging reduces the use of raw materials in the man-
ufacturing process and also reduces the amount of waste in landfill
sites. Your dealer will take the packaging materials away.
Disposing of your old appliance
Electrical and electronic appliances often contain valuable materials.
They also contain specific materials, compounds and components,
which were essential for their correct function and safety. These
could be hazardous to human health and to the environment if dis-
posed of with your domestic waste or if handled incorrectly. Please
do not, therefore, dispose of your old appliance with your household
waste.
Please dispose of it at your local community waste collection / recyc-
ling centre for electrical and electronic appliances, or contact your
dealer or Miele for advice. You are also responsible (by law, depend-
ing on country) for deleting any personal data that may be stored on
the appliance being disposed of. Please ensure that your old appli-
ance poses no risk to children while being stored prior to disposal.

Caring for the environment
15
Energy saving tips
Energy and water
consumption
- To get the most out of your machine, load the maximum dry load
size for the wash programme you are using.
Energy and water consumption is most efficient when a full load is
washed.
Detergent - Do not exceed the amounts of detergent recommended by the
manufacturer on the packaging.
- Reduce the amount of detergent for smaller load sizes.
When drying with
a tumble dryer
Select the highest possible spin speed for the wash programme to
save energy in the subsequent tumble dryer cycle.

Description of the machine
16
Machine description
⑥
⑦
①
②
③
④
⑤
aEmergency-off button
Pressing the red button switches the machine off.
bControl panel
cDetergent drawer
Pull the handle to open the flap.
dDoor handle
The door handle is equipped with an anti-snap mechanism to ensure the safety function
of the door lock.
eDrum door
Pull the door handle to open the drum door. Never use force to open the drum door.
fService panel
gPlinth panel

Description of the machine
17
Control panel
aDisplay
1 Cottons hygiene 90
2 Cottons universal 60
3 Cottons intensive 60

°C
°C
°C
When the machine is switched on the welcome screen will appear briefly, followed by
the programme list. The last started programme is highlighted.
bFunction buttons
The six buttons underneath the display are the function buttons. These buttons can be
allocated specific functions depending on the status of the machine. These functions
appear in the display above the buttons and are highlighted when selected. By repro-
gramming “Direct button allocation”, the first six programmes in the programme list can
be selected using buttons 1–6.
cStart button
The light ring around the button flashes when a selected programme is ready to start.
The selected programme starts when the start button is pressed. After a programme has
been started, the display content can be shown again by pressing this button.
dPC optical interface
Using PC software, data can be transmitted to and from the controls to a PC. The op-
tical interface on the control panel provides the connection point.
eRotary control
Rotating the outer ring allows changes to be made to the display selection and input
fields and also confirms these changes.
fCard reader
When a card is inserted, the wash programmes on the card can be used. Insert the card
in the direction of the arrow.
gI Power on button
Switch on the machine
h0 Power off button
Switch off the machine
iEmergency-off button
Only use in case of danger. Pressing the red button switches the machine off. When the
hazard has been removed, the button can be unlocked by turning it clockwise. When
the “START”button is pressed again, the interrupted programme continues.

Description of the machine
18
Function buttons
A function is activated when pressed and deactivated when pressed again.
Stop/finish
The right-hand function button is used as the finish button after a programme has started.
Pressing the button stops the selected programme or finishes a stopped programme.
+ Block+
The corresponding programme block (e.g. Pre-wash) is added to the programme.
 Starch stop
Press this button if the laundry is to be starched.
 Without spin
Press this button if a final spin is not required after the final rinse.
 Settings
Another language can be temporarily selected by pressing this button.
 Start date and time
When this button is pressed before starting the programme, information about selecting a
start time will appear in the display.
 Information
Programme information appears in the display when this button is pressed.
Water drainage
 Manual control
See programming instructions
 Change order
The current programme can be skipped or programme blocks can be repeated.
 Back
Return to previous display page.
/ Information on next/previous line
Saving
See programming instructions
 Programme locked
If a programme is locked, after 1minute it can no longer be stopped and cancelled with
the finish button.
 Programme unlocked
 Dispensing
 Dispensing switched off
Operating data
Resetting to 0 (taring)
If the load display does not show “00.0” with an empty drum, this can be rectified by
pressing this button.
 Data transfer

Description of the machine
19
Programme card for the supervisor
There are no programmes on this card ex works. Please refer to the programming instruc-
tions for information on how data is transferred from the controls to the card.
If a card with saved programmes is placed in the card reader before the programme is
started, the controls no longer access the internal programme memory. The content of
the card is read and shown in the display as a programme list with the indication Card op-
eration.
The card can hold a maximum of 30programmes consisting of 6blocks each. The back of
the card can be labelled.

Washing
20
Initial commissioning
The washing machine must be commissioned by the Cus-
tomerService Department or an authorised dealer.
Open the on-site shut-off valves for water and/or steam.
Switch on the (on-site) power switch.
Switch the machine on with the I“Power on”button.
M
PROFESSIONAL
PW 6xx1
Welcome
The welcome screen will appear in the display,
1 Cottons hygiene 90
2 Cottons universal 60
3 Cottons intensive 60

°C
°C
°C
followed by the programme list (the last started programme is high-
lighted).
Rotate the rotary control to select a programme and press the
“START”button to start it immediately.
Preparing the laundry
Emptying pockets
Empty all pockets.
Damage due to foreign objects.
Nails, coins, paper clips, and so on can cause damage to garments
and components in the machine.
Check the laundry before washing and remove any foreign objects.