Miele Touchtronic W 3033 Parts list manual

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010107
Product Dimensions
Large Capacity Washing Machine
Angled control
W3033 / W3035
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
D
W
E
3 3/4" - 4 1/2"
21 1/2"
D -
E -
W -
5 foot flexible drain hose connects
upper left rear.
120 Volt, 15 Amp 5 foot molded plug
power supply connects upper left rear
(NEMA5-15Configuration).
5 foot separate flexible hot and cold
water intake hoses connect upper left
rear.
Location Codes
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Remove transport struts in rear of machine before installation.

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010107
Product Dimensions
Large Capacity Washing Machines
Flat controls - Decor Unit
W3039
2"
23 1/2"
33 3/8" - 34 1/8"
22 1/2"
5 7/8"
3 3/4" - 4 1/2"
1 1/2"
Decor White
D
W
E
D -
E -
W -
5 foot flexible drain hose connects
upper left rear.
120 Volt, 15 Amp 5 foot molded plug
power supply connects upper left rear
(NEMA5-15Configuration).
5 foot separate flexible hot and cold
water intake hoses connect upper left
rear.
Location Codes
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Remove transport struts in rear of machine before installation.

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010107
Cut-out Dimensions
Built-in Installations
Large Capacity Laundry Products
24"
See Notes
Water & Electrical
Connection
Location
C
32 3/8" - 35 1/4"
• Typically requires removal of unit's lid. Out of box unit height dimension without
lid is 32 5/16" - 32 11/16".
Notes
Location Codes
C - Cutout for Electric and Vent or Drain
pass-through. Adjust according to duct
or drain location.

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010107
Product Dimensions
Laundry Stand
WTS420 - White Only
22"
11"
Notes
• For use with both large and super
capacity washers or tumble dryers.
• All installations must be done in
accordnace with local codes
23 3/8"

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010107
Product Dimensions
Stacked Washer & Dryer
Example Combination
W3033 + T8002
2"
D
W
E1
3 3/4" - 4 1/2"
23 1/2"
22 1/2"
66 3/8" - 67 1/8"
V
E2
D -
E1 -
E2 -
W -
5 foot flexible drain hose connects
upper left rear.
120 Volt, 15 Amp 5 foot molded plug
power supply connects upper left rear
(NEMA5-15Configuration).
208/240 Volt, 30Amp 5 foot molded
plug power supply connects upper
right rear (NEMA 14-30 Configuration).
5 foot separate flexible hot and cold
water intake hoses connect upper left
rear.
Location Codes
Notes
• All installations must be done in accordance with local codes
• See "Cut-out Dimensions" sheet for undercounter or built-in space requirements
• Remove transport struts in rear of machine before installation.

NOTE: Drawing is not to scale.
SPECIFICATION SHEETS 010107
Panel Information
Integrated Laundry
W3039 Decor Unit
These units come equipped with a full size white front panel. These units are also designed to either accept a thin insert or
a custom front panel supplied by the custom cabinet maker.
Sizes are as follows: Version 1 - Thin insert
Width: 23 1/4" for all machines
Thickness: up to 1/8"
Height: 25" in all cases
With this version, a thin white frame will be exposed after
installation
Version 2 - Custom Front Panel
Width: 23 3/8" for all machines
Thickness: up to 3/4"
Height: Up to 25"
With this version, the existing front panel is removed and
replaced by the new custom panel
Miele
Decor
Laundry unit
Hinge Notches
In certain installations, notches will be required to
accomodate the hinges in the front panel.
Miele
Decor
Laundry
Control
Panel
To center lines
16 3/4"
Notch Pattern
For this installation, drill the following
pattern in the appropriate locations.
Note: To insure access to customer servicable features,
a minimum 4" toe kick above finished floor (AFF)
is required.
3 7/8"
C
C
C
1 1/8"
7/8"
1/4" Ø
1/4" Ø
1"
1"
Drill all holes
to a 5/8" depth
1 3/8" Ø